Manuale d’uso / di manutenzione del prodotto TPS53125EVM-599 del fabbricante Texas Instruments
Vai alla pagina of 17
User's Guide SLVU392 – July 2010 TPS53125EVM-599 The TPS53125EVM-599 Evaluation Module presents an easy-to-use reference design for a common dual output power supply using the TPS53125 controller in cost-sensitive applications. Also included are the schematic, board layout, and bill of materials.
Description www.ti.com List of Tables 1 TPS53125EVM-599 Electrical and Performance Specifications ...................................................... 2 2 Test Point Description .......................................................................
+ + + + + www.ti.com TPS53125EVM-599 Schematic 3 TPS53125EVM-599 Schematic For Reference Only, See Table x: for Specific Values Figure 1. TPS53125EVM-599 Schematic 3 SLVU392 – July 2010 TPS53125EVM-.
Connector and Test Point Descriptions www.ti.com 4 Connector and Test Point Descriptions 4.1 Enable Jumpers/Switches –SW1 and SW2 The TPS53125EVM-599 board includes independent enable switches for each of the two outputs.
www.ti.com Test Setup 4.2.4 Soft-Start Voltage Monitoring – TP1, TP2, and TP3 TPS53125EVM-599 provides two test points for measuring the soft-start ramp voltages. TP1 monitors the soft-start ramp of Channel 1. TP2 monitors the soft-start ramp of Channel 2.
Test Setup www.ti.com J1 to LOAD1 and J2 to LOAD2 - The connection between J1 and LOAD1 and J2 and LOAD2 of TPS53125EVM-599 can carry as much as 4 Adc each. The minimum recommended wire size is AWG #14, with the total length of wire less than 2 feet (1-foot input, 1-foot return).
LOAD1 1.05V @ 4A F AN V2 + - Oscilloscope 1M W , AC 20mV / div 20MHz LOAD2 1.8V @ 4A V3 - + - + - + A1 - + V VIN V1 + - www.ti.com Test Setup 5.2.2 Test Setup Diagram Figure 2. TPS53125EVM-599 Recommended Test Setup 5.3 Start-Up/Shutdown Procedures Perform the start-up and shutdown procedures in the following manner.
0 1 2 3 4 5 I -LoadCurrent- A LOAD 50 55 60 65 70 75 80 85 90 95 h -Efficiency-% V =8V I V =12V I V =22V I TPS53125EVM-599 Test Data www.ti.com 7. Decrease LOAD2 to 0 A. 5.4 Output Ripple Voltage Measurement Procedure Perform the Output Ripple Voltage Measurement procedure in the following manner.
0 10 20 30 40 50 60 70 80 90 100 h -Efficiency-% 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 I -LoadCurrent- A LOAD V =8V I V =12V I V =22V I V =8V I V =12V I V =22V I 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 I -LoadCurrent- A LOAD 1.
1.82 1.825 1.83 1.835 1.84 1.845 1.85 1.855 1.86 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 I -LoadCurrent- A LOAD V -OutputV oltage-V O V =8V I V =12V I V =22V I TPS53125EVM-599 Test Data www.ti.com V IN = 8 V – 22 V, V OUT1 = 1.
www.ti.com TPS53125EVM-599 Test Data V IN = 12, V OUT2 = 1.80, I OUT2 = 4 A Figure 8. TPS53125EVM-599 Output Voltage Ripple 6.4 Switch Node tV IN = 12, V OUT1 = 1.
TPS53125EVM-599 Assembly Drawings and Layout www.ti.com V IN = 12, V OUT2 = 1.80, I OUT2 = 4A Ch1: TP11 (SW2) Figure 10. TPS53125EVM-599 Switching Waveforms 7 TPS53125EVM-599 Assembly Drawings and Layout The following figures ( Figure 11 through Figure 15 ) show the design of the TPS53125EVM-599 printed-circuit board.
www.ti.com TPS53125EVM-599 Assembly Drawings and Layout Figure 12. TPS53125EVM-599 Top Copper, Viewed From Top Figure 13. TPS53125EVM-599 Bottom Copper, Viewed From Bottom 13 SLVU392 – July 2010 TPS.
TPS53125EVM-599 Assembly Drawings and Layout www.ti.com Figure 14. TPS53125EVM-599 Internal 1, X-Ray View From Top Figure 15. TPS53125EVM-599 Internal 2, X-Ray View From Top 14 TPS53125EVM-599 SLVU392.
www.ti.com TPS53125EVM-599 Bill of Materials 8 TPS53125EVM-599 Bill of Materials The Table 3 contains the bill of materials for TPS53125EVM-599. The reference designators reference the schematic in Figure 1 and assembly locations in Figure 11 . The components listed with a quantity of 0 are not populated on the PCB but are provided for reference.
Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Texas Instruments TPS53125EVM-599 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Texas Instruments TPS53125EVM-599 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Texas Instruments TPS53125EVM-599 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Texas Instruments TPS53125EVM-599 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Texas Instruments TPS53125EVM-599, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Texas Instruments TPS53125EVM-599.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Texas Instruments TPS53125EVM-599. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Texas Instruments TPS53125EVM-599 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
