Manuale d’uso / di manutenzione del prodotto DC-820B del fabbricante Tekram Technology
Vai alla pagina of 56
1 EISA Fast SCSI Caching Adapter DC-820B Mirroring + Caching EISA Fast SCSI Host Adapter Acknowledgements of the following trademarks: Intel is a registered trademark of Intel Corporation. Adaptec, ASPI, and AHA 1540/1542 are registered trademarks of Adaptec.
EISA Fast SCSI Caching Adapter 2 FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.
3 EISA Fast SCSI Caching Adapter . DOS - Sec 0.1: A:> INSTALL . NetWare - Chap 3 . UNIX - Chap 4 Re-boot the system & Play!!! YY Install Driver? . Install the cache DRAM - Sec 1.4 . Set your SCSI HDD's ID to 0 and 1 (if avail- able) . Plug the adapter onto your system & Cabling .
EISA Fast SCSI Caching Adapter 4 T able of Contents Chapter 0 INTRODUCTION ....................................................... 6 0.1 Easy DOS Driver Installation Software (INSTALL.EXE) ............................... 7 Chapter 1 HARDWARE SETUP ...
5 EISA Fast SCSI Caching Adapter Appendix A. Technical Specification ....................................... 50 Appendix B. Product Support Form ........................................ 52 Appendix C. General Troubleshooting Tips .....................
EISA Fast SCSI Caching Adapter 6 Chapter 0 Introduction The DC-820B is an intelligent multi-tasking SCSI (Small Computer System Interface) bus to EISA bus host adapter. Up to six DC-820B adapters can be installed in one system with each adapter supporting up to seven SCSI devices.
7 EISA Fast SCSI Caching Adapter All versions of MS-DOS support two hard disk drives without adding device drivers. If MS-DOS 5.0 is used, the DC-820B BIOS can handle up to eight devices, including fixed disk and removable media, by enabling the DOS 5 Support enable/disable option during the ECU (EISA Configuration Utility) setup process.
EISA Fast SCSI Caching Adapter 8 more than one adapter co-existing in the system, then you must select which adapter you want to work with. The System has the following Host Adapter(s) 1 DC-820B HA#0 Base 330H DMA 5 IRQ 11 ID 7 2). This screen provides the information of the SCSI devices controlled by the chosen adapter (HA#0).
9 EISA Fast SCSI Caching Adapter 3) The following screen provides you the information about how many SCSI devices installed in the system and requires you to answer if to install the driver(s) or not:.
EISA Fast SCSI Caching Adapter 10 And then you go on to assign the first drive letter for the CD-ROM drive(s) used by the MSCDEX.EXE. In this case, Drive: F is reserved to the first CD-ROM drive. 4) . After confirmation, this installation program will modify both the CONFIG.
11 EISA Fast SCSI Caching Adapter.
EISA Fast SCSI Caching Adapter 12 Chapter 1 HARDW ARE SETUP Before plugging the DC-820B into your system, make sure all jumpers on the card are correctly set according to instructions outlined in section 1.
13 EISA Fast SCSI Caching Adapter Warning: Do not power-down the system while this LED is still active. Doing so may result in loss of data as the contents of the cache buffer have not been completely written to the disk.
EISA Fast SCSI Caching Adapter 14 external cables, respectively. As in the above case, remove the terminators from all devices connected in between. Store the terminators in a safe place for future use, if necessary. 1.3 Cable Connection (CN1, CN2, & CN3) There are three connectors on your DC-820B: CN1, CN2, and CN3.
15 EISA Fast SCSI Caching Adapter installed, you can only install the SCSI drive with SCSI ID 0 as drive D:. If two IDE/ST506/ESDI drives already exist, no SCSI drives can be installed as C: or D:. When no IDE/ST506/ESDI drive exists, two SCSI drives with SCSI ID’s 0 and 1 can be installed as drives C: and D:, respectively.
EISA Fast SCSI Caching Adapter 16 1. Set I/O port address as 330H. 2. Set the SCSI ID as 0 and 1 for fixed disk drives. 3. Device drivers are needed for other SCSI devices, such as removable cartridge, re-writable optical disk (MO), tape streamer, DAT, and CD- ROM.
17 EISA Fast SCSI Caching Adapter 1.6.1 DC-820B Adapter Hardware Options This field allows you to select the Interrupt level, Adapter BIOS address, I/O port address, and DMA channel. Since most options in this category are Adaptec-compatible, some enhanced options will be pointed out specifically.
EISA Fast SCSI Caching Adapter 18 BIOS INT 13H. Device drivers have no effect if this Disabled option is chosen. * WARNING (if coexists with IDE HDD) * IRQ14 is used by the Primary IDE IRQ Channel & IRQ15 is used by the Secondary IDE IRQ Channel Host Adapter BIOS ADDRESS: DC000H - default.
19 EISA Fast SCSI Caching Adapter SCSI ID 7. These scanning rules apply to an environment with multiple adapters or devices. DMA Channel Definition: DMA 5 - default. This option is a pseudo- function for Adaptec compatibility. Since some software packages do require a DMA channel, there are four channels available: DMA 5/6/7/0.
EISA Fast SCSI Caching Adapter 20 Cache Size 1MB 4MB 16MB DOS/Windows 4KB/line 16KB/line 16KB/line NetWare 4KB/line 16KB/line 16KB/line UNIX 4KB/line 8KB/line 16KB/line Cache DRAM test: Suppressed/Simplified/Full test. Suppressed test is the default option and would just skip the test on cache DRAM to save time for system boot-up.
21 EISA Fast SCSI Caching Adapter Device Case 0 Case 1 Case 2 IDE HDD 0 none drive C: drive C: IDE HDD 1 none none drive D: SCSI device 0 (SCSI ID = 0) drive C: drive D: (*) SCSI device 1 (SCSI ID = 1) drive D: (*) (*) *: Not recognized by BIOS INT 13H, if existing.
EISA Fast SCSI Caching Adapter 22 F:, and so on. The following demonstrates the case of one IDE adapter with two IDE HDD drives and two DC-820Bs with seven SCSI drives.
23 EISA Fast SCSI Caching Adapter Power ON delay for SCSI devices: 30 - 120 seconds. The 30 seconds power-on delay default is applicable to most drives. Since some slower drives may fail to respond within the default power-on delay duration, you may extend this time duration in order to give sufficient time for start-up.
EISA Fast SCSI Caching Adapter 24 Cacheable device: Yes/No. This option is only valid for fixed disk, remov- able cartridge, re-writable optical disk (MO) and Floptical. The removable media device with Yes option must insert the media before the system boot- up for caching algorithm to work properly.
25 EISA Fast SCSI Caching Adapter Mirrored to SCSI ID: NO/1-7. This disk mirroring function is implemented by the DC-820B’s firmware and works for all operating systems. This option needs two and only two drives and is selected from the slave drive’s point of view .
EISA Fast SCSI Caching Adapter 26 1.7 TOOLBME.EXE Utility & Disk Mirroring Initialization TOOLBME.EXE is a utility program performing the functions of Low-Level Format, Disk Copy, Disk Compare, and Mirroring Initialization.
27 EISA Fast SCSI Caching Adapter This screen gives us the information about the adapter-0 has five SCSI devices (ID ranging from 0 to 4) and the FUJITSU M2614S/MAXTOR LXT-200S joined as a mirror pair.
EISA Fast SCSI Caching Adapter 28 always duplicates the Master Disk to the Backup Disk ( slave ). If one of the Mirror-Pair drives is malfunctioning, you can try to adjust the proper Mas- ter-Backup relation by selecting the Mirrored to SCSI ID in the ECU and then execute this module to put things in order.
29 EISA Fast SCSI Caching Adapter If both the Master and Backup Disk drives are new or contain useless data, you may key in Y instead to proceed the initialization:.
EISA Fast SCSI Caching Adapter 30 Disk image copy utility: This module copies the data from the Source Disk to the Target Disk on a drive-to-drive basis. Still, you have to set the copy- pair drives, one to Source Disk and the other to Target Disk , by pressing the <Space Bar>.
31 EISA Fast SCSI Caching Adapter Adapter Error Log utility: This module provides the I/O error log informa- tion for the devices controlled by the DC-820B(s). When this module is selected, the screen will display the information of I/O port address corre- sponding to each adapter, which is an Adaptec adapter or its compatible.
EISA Fast SCSI Caching Adapter 32 Chapter 2 ASPI Driver for DOS This chapter describes the ASPI (Advanced SCSI Programming Interface) driver installation for DOS and some other useful utility programs under this ASPI environment: 1. The ASPI driver, ASPIBME.
33 EISA Fast SCSI Caching Adapter 2.1 Installing the ASPI Driver With ASPI driver, ASPIBME.SYS, installed, you are able to run or install the following drivers and utilities: n TFDISK.EXE: Disk partition utility in this diskette n DISKDRV.SYS: Disk driver in this diskette n AFDISK.
EISA Fast SCSI Caching Adapter 34 drives) reserved with the driver within 16. This option is important for removable media devices. If you do not reserve enough logical drives for your removable media, it may cause some of the logical drives to go unrecog- nized.
35 EISA Fast SCSI Caching Adapter Drive A: Floppy drive Drive B: Floppy drive Drive C: Adapter 0, SCSI ID 0 (BIOS INT 13H controlled HDD) Drive D: Adapter 0, SCSI ID 1 (BIOS INT 13H controlled HDD) Dr.
EISA Fast SCSI Caching Adapter 36 2.3 Disk Partition Utility TFDISK.EXE is a DOS-compatible disk partition program for modifying or creating a partition table. Valid DOS partitions can be created by DOS FDISK for drives controlled by BIOS INT 13H or TFDISK.
37 EISA Fast SCSI Caching Adapter Special translation method This method partitions the drive to work with other Tekram adapters. Heads = 8/16/32/48 Sectors = 26/32/48/63/64/128/192 Cylinders = xxx depends on drive’s capacity (The head # and Sector # will be calculated automatically, and can not be modified manually.
EISA Fast SCSI Caching Adapter 38 Usable: Means this drive is all right to work with. 2.5 Installing the CD-ROM Driver ASPICD.EXE is a driver for CD-ROM and CD-Changer devices. Besides that, you still need one more execution file, mscdex.exe, which can be acquired from Microsoft.
39 EISA Fast SCSI Caching Adapter.
EISA Fast SCSI Caching Adapter 40 Chapter 3 NetW are Drivers The DC-820B supports drivers for NetWare V3.10/3.11/3.12/SFT-III/4.00/ 4.01 under separate directories to support fixed disks, removable media, and tape subsystems. <NetWare.40X> This directory supports drivers for NetWare V4.
41 EISA Fast SCSI Caching Adapter n BELOW16.DSK is the memory allocator routine for buffer below 16 megabyte under NetWare V3.10. This file will be auto-loaded during installation. The similar function is default supported under NetWare V3.11. 3.1 ASPI drivers for NetW are A).
EISA Fast SCSI Caching Adapter 42 choosing the I/O slot number, the screen will display information about the configuration of the adapter selected: Host Adapter = DC820B I/O Port Address = 330 (Hex) .
43 EISA Fast SCSI Caching Adapter Somehow the operating system must be informed of the change and new disk geometry be passed on in order that the new file system is recognized. For proper installation, be sure to follow the procedure below when using removable media devices.
EISA Fast SCSI Caching Adapter 44 1. Select Disk Information 2. Select the corresponding drive with removable media 3. Move the inverted cursor bar to the item Removable Drive Mount Status : and choose dismount to dismount the device 4. Media ejection is now possible.
45 EISA Fast SCSI Caching Adapter.
EISA Fast SCSI Caching Adapter 46 Chapter 4 UNIX LOCK/UNLOCK Driver Packages This chapter introduces the installation procedures of UNIX LOCK/UNLOCK support for removable media devices. It is especially important for removable media devices that employ the caching capability supported by the DC-820B.
47 EISA Fast SCSI Caching Adapter The procedure is the same as ISC UNIX V3.2 (refer to Sec 4.2). Removable media support This driver supports removable media like the Magneto-Optical drive. Upon successful installation, two utility files rmount and rumount will be found under /etc to replace original “mount” and “umount” commands.
EISA Fast SCSI Caching Adapter 48 Driver Removal To remove the driver, follow these procedures: 1. At the prompt, type removepkg 2. Type the corresponding number of: “EISASC Lock/Unlock Driver Package” 3. Press <Enter> to remove the driver 4.
49 EISA Fast SCSI Caching Adapter.
EISA Fast SCSI Caching Adapter 50 Appendix A: T echnical Specifications Performance n Cache DRAM sizes: Not-Installed/1MB/4MB/16MB n Hardware Disk mirroring support n High speed 32-bit bus master, bur.
51 EISA Fast SCSI Caching Adapter Functional n Enhanced SCSI I/O protocol: Multi-threaded & Multi-tasking support, Enhanced mailbox structure breaking 16MB bus master addressing limit, and Scatter/Gather data transfer support n EISA Auto-configuration support n Easy DOS driver installation software (INSTALL.
EISA Fast SCSI Caching Adapter 52 Appendix B: Product Support Form The following information should be provided to your supplier in writing to obtain technical support assistance: 0. Ever try General Troubleshooting Tips in Appendix C and without suc- cess? Yes? ____ No? ____ 1.
53 EISA Fast SCSI Caching Adapter n Other SCSI device(s) : 1. _____________________ 2. _____________________ 3. _____________________ 4. _____________________ 3. System Software Configuration (please list the version) n Operating System : _____________________ n Application Program : _____________________ 4.
EISA Fast SCSI Caching Adapter 54 Appendix C: General T roubleshooting T ips Most controller errors are traceable to external factors, such as conflicts with other installed cards, bad or incorrectly configured drives, loose cables, or other installation errors.
55 EISA Fast SCSI Caching Adapter 2. No BIOS message from DC-820B appears on the screen: n ROM address conflicting with other I/O card(s) -> check the ROM addresses of all the I/O cards and make su.
EISA Fast SCSI Caching Adapter 56 This is also a common measure used by other caching adapters, such as Mylex, to improve the performance. Of course, if you turn the cache off, i.e., set the "Cacheable device" option to "No", and you'll find things are back to they used to be.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Tekram Technology DC-820B è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Tekram Technology DC-820B - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Tekram Technology DC-820B imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Tekram Technology DC-820B ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Tekram Technology DC-820B, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Tekram Technology DC-820B.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Tekram Technology DC-820B. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Tekram Technology DC-820B insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
