Manuale d’uso / di manutenzione del prodotto Blend 16 del fabbricante Tapco
Vai alla pagina of 28
#MFOE #MFOE o w n e r’ s m a n ua l 1 6 -CHANNEL 4 -BUS MIXER w/ O N B OA R D E F F E C T S.
2 SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
Part No. SW0426 Rev. A 08/2006 ©2006 LOUD T echnologies Inc. All Rights Reserved. 3 What me, read a manual? Before you begin, please make sure that you read the Safety Instructions on page 2 and Getting Started on page 4. One will help you keep safe, and the other will get you started using your new T APCO ® Blend 16 mixer .
4 G e t t i n g S t a r t e d The following steps will help you set up your mixer , and get the levels and adjustments just right. Please follow the instructions in the order they are presented, rather like following the instructions for mixing a lemon bundt cake, or running a nuclear power station, for example.
5 9. Now that you have a rough mix going, you may need to readjust the MAIN MIX F ADER to a comfortable listening level. The meters should indicate by lighting most of the green LEDs when music is playing, and occasionally light the yellow. 10. Depending on how much time you have, keep tweaking.
6 Here’s a quick glance at all the features pac k ed into this mix er: 8 mono mic/line channels, with: • XLR microphone input jack • 1/4" TRS instrument input jack • 1/4" TRS insert .
7 LEFT RIGHT 1 2 3 4 SU B OUT S MA IN IN SE RT LEFT BAL/UNBAL BAL/UNBAL TIP SEND / RING RETURN RIGHT CO NT ROL R M OU T US B IN/ OU T MA IN OU T RIGHT LEFT AUX SENDS LINE INPUT L R BAL OR UNBAL ( MONO.
8 LEFT RIGHT 1 2 3 4 SUB OUTS MAI N INS ERT LEFT BAL/UNBAL BAL/UNBAL TIP SEND / RING RETURN RIGHT CON TROL RM O UT USB IN/O UT MAI N OUT RIGHT LEFT AUX SENDS LINE INPUT L R BAL OR UNBAL ( MONO ) MIC I.
9 B l e n d 1 6 F e a t u r e s MONO CHANNELS Mono channels 1 to 8 allow adjustment of EQ, Pan, and Level for mono signals. The output from each channel strip can be assigned to the main mix and subgroups. Auxiliary signals can be tapped off and sent to Aux bus 1 (monitors) and Aux bus 2 (effects).
10 8. MID FREQ EQ This adjusts the frequency of the MID EQ (9) control from 100 Hz to 8 kHz. This gives you great flexibility in shaping your sound. Listen carefully for its effect. 9. MID EQ T ur n this clockwise to boost the level of signals around the frequency set by the MID FREQ (8) control.
11 For an example, suppose your band is per for ming on stage, and you hear something unusual (well, more unusual than normal). W ithout interrupting their per for mance, you can Solo each channel in turn, and listen in the headphones until you identify the problem channel or band member .
12 A UX SENDS and RETURNS 22. A UX 1 SEND MON OUTPUT T o create a stage monitor mix, connect this 1/4" TRS output to the input of your stage monitor amplifier (or powered monitors). Each channel’s AUX SEND 1 MON (11) knob adjusts how much of the channel’s signal appears on the AUX 1 bus.
13 U U MA X PH ON ES LA MP BY PAS S EQ IN FX OL MA IN MIX AU X1 ( MON ) PO WE R PH AN TO M 4 8V 1 MA IN MI X SU B 2 SU B 3 SU B 4 SU B SUB AS SIG N TO MAI N M IX M A S T E R A UX SE ND CT RL R M PH ON.
14 INTERNAL EFFECTS The internal effects circuit receives mono signals from the AUX 2 FX bus, and it outputs stereo signals onto the main mix buses. It also adds a summed mono signal to the stage monitor mix (AUX 1 bus). The outputs are controlled by two FX RETURN (45, 46) knobs described on the next page.
15 38. USB OUTPUT: MAIN MIX/SUBS 1-2 This switch allows you to choose if the main mix or if subgroups 1 and 2, are sent out of the mixer’s USB (62) output to your computer . If pressed in, the A/D converters of the USB section receive the output from subgroups 1 and 2 (before the SUB F ADERS (50)).
16 amplifiers clip at about +10 dB, and some recorders aren’t so forgiving either . For best real-world results, try to keep your peaks between 0 dB and +8 dB. If your meters are too high, you will get distortion. If they are too low, then your signal-to-noise will suffer .
17 REAR P ANEL FEATURES 53. POWER SWITCH Push the top of the switch labeled “ON” to turn the mixer on; you should see the POWER LED (27) glow with happiness. T o tur n the mixer off, push the bottom of the switch. As a rule, turn the mixer on first, before any amp or powered speakers.
18 A p p e n d i x A : U s i n g t h e B l e n d 1 6 At first glance, the controls on the front panel of the Blend 16 may seem more at home in a space movie, right next to the Navigation officer .
19 Three controls configure how the USB connection will work in different scenarios: USB Source switch: This lets you choose whether your computer is fed by the main mix, or by a prefader tap of subgroups 1-2.
20 Studio: Direct Monitoring Configuration: 1. Connect your mics and instruments to the mixer’s inputs (leave channels 15-16 unused). 2. Connect your amplifier/speaker system (or powered speakers) to the Control Room outputs, or connect headphones to the Phones output.
21 A p p e n d i x B : C o n n e c t i o n s XLR Connectors Channels 1 and 2 use 3-pin female XLR connectors on the MIC inputs. They are wired as follows, according to standards specified by the AES (Audio Engineering Society).
22 A p p e n d i x C : S p e c i fi c a t i o n s Frequenc y Response Mic Input to any Output (T rim at 0 dB): +0, –1 dB, 20 Hz to 20 kHz –3 dB, 10 Hz to 80 kHz Distortion THD and SMPTE IMD; 20Hz to 20kHz Mic Input to Main Output: < 0.
23 Ph ysical Dimensions and W eight Height: Back: 5.0” (127 mm) Front: 2.5” (64 mm) Width: 18.5” (469 mm) Depth: 16.6” (422 mm) W eight: 11.5 lbs (5.2 kg) Inter nal Effects 32 bit EMAC processing, 2-channel Sample Rate: 31.25 kHz Bandwidth: 15.
24 Block Diagram This shows an outline of the strange goings on inside the mixer . L R L R 1 2 3 4 A UX 1 A UX 2 SOLO LOGIC SUB L R 1 2 3 4 CONTROL ROOM LEVEL MAIN F ADER EQ MAIN /MON EQ EQ BYP ASS PH.
25 A p p e n d i x D : S e r v i c e I n f o rm a t i o n No A udio into your Computer: • Confir m the mixer is receiving mic or instrument input signals. • Make sure you have selected the right driver in your DA W . In T racktion, this is in the Settings menu.
26 No Communication with the mix er: • The PC driver may not be installed correctly. Make sure your computer meets the system requirements. Uninstall the driver from the Add/ Remove Programs control panel, restart your computer , and reinstall the driver .
27 T A P C O L I M I T E D W A R R A N T Y A. LOUD T echnologies Inc. warrants all materials, workmanship and proper operation of this T APCO product for a period of one year fr om the original date of purchase.
#MFOE #MFOE o w n e r’ s m a n ua l 1 6 -CHANNEL 4 -BUS MIXER w/ O N B OA R D E F F E C T S.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Tapco Blend 16 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Tapco Blend 16 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Tapco Blend 16 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Tapco Blend 16 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Tapco Blend 16, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Tapco Blend 16.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Tapco Blend 16. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Tapco Blend 16 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
