Manuale d’uso / di manutenzione del prodotto EH64 del fabbricante Subaru Robin Power Products
Vai alla pagina of 24
The engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects or other reproductive harm. INSTRUCTIONS FOR USE MODEL EH64 WELDER APPLICA TION W ARNING 2ZZ-90201-07 CONTENTS LIMITED ENGINE W ARRANTY .
3 Y ear Limited Engine W arranty (Special T erm for W elder Application) (Effective with engines purchased from Robin America, W ood Dale, IL, after November 15, 1993) Robin America, Inc.
NOTICE FEDERAL EMISSION COMPONENT DEFECT WARRANTY and CALIFORNIA EMISSION CONTROL WARRANTY are applicable to only those engines complied with EPA (Environmental Protection Agency) and CARB (California Air Resources Board) emission regulations in the U.
moving parts, etc. • Used engine oils have been identi fi ed by some state and federal agencies as causing cancer or reproductive toxicity . When checking or changing engine oil, take care not to ingest, breathe the fumes, or contact used oil.
9 10 Introduction ABOUT THIS MANUAL This manual covers the operation and maintenance of the horizontal- shaft Robin Subaru EH64 engines for welder applications (OHV220 Performer Series). Each operator of the power equipment should study this engine manual carefully and observe all of its instructions and precautions.
Description FEA TURES • Overhead valve arrangement enables high power , and low fuel and oil consumption • V -T win, four stroke design • Air-cooled and gasoline fueled • The light weight and compact design makes it easy to install and utilize for many applications.
13 14 Installation LOCA TING Locate the engine at least 1 meter (3.0 ft) away from buildings or other structures. Provide proper exhaust routing. Refer to EXHAUST SYS- TEM below . Do not use the engine near fl ammables or other hazard- ous materials such as trash, rags, lubricants, or explosives.
ENGINE OIL Recommendations Use premium quality motor oil, Class SE or higher . Look for the SAE (Society of Automotive Engineers) or API viscosity grade. Referring to the table below , choose the viscosity grade appropriate for the ambient temperatures expected during the period of time until the next sched- uled oil change.
17 18 BA TTERY CABLES Installation ST ARTER SWITCH A customer supplied starter switch or key switch is recom- mended for the starter motor . See table below for switch cable recommendations. WIRE GAUGE CABLE LENGTH CABLE DIA. AWG (BS) BWG SAE JIS Less than 1.
19 20 ENGINE WIRING DIAGRAM (6 PIN) Engine Speci fi cation Numbers: EH650DB2332 EH650DB2341 EH650DB2390 ENGINE WIRING DIAGRAM (4 PIN) Engine Speci fi cation Number: EH650DB2332 Wiring Diagram POWER .
22 21 Operation EXHAUST GAS IS DEADL Y! Exhaust gases contain carbon monoxide, an odorless and color- less gas. Carbon monoxide is poisonous and can cause uncon- sciousness and death.
23 24 In colder weather , the engine will take longer to begin running smoothly with the choke open. Do not operate the equipment until the choke is fully open.
25 26 ! W ARNING EXHAUST GAS IS DEADL Y! Never operate engine-powered equipment indoors without a proper exhaust system, ample fresh air ventilation and an operable carbon monoxide detector . 2. Use fresh gasoline and fi ll the fuel tank after each day’ s use to reduce problems with moisture condensation if this is a gasoline engine.
27 28 Periodic Maintenance MAINTENANCE, REPLACEMENT , OR REP AIR OF THE EMISSION CONTROL DEVICES AND SYSTEMS MA Y BE PERFORMED BY NON-ROAD ENGINE REP AIR EST ABLISHMENTS OR INDIVIDUALS. Periodic maintenance is essential for top engine performance. See the T able below as a guide for normal periodic maintenance.
Crankcase pressure can blow hot engine oil out the fi ll tube causing severe burns. Always stop the engine before removing the oil fi ll cap. If the engine is equipped with the long oil fi ll tube, turn the oil fi ll cap counterclockwise and lift it up.
31 32 10 DO NOT FILL T O A LEVEL ABOVE THE FULL MARK ON THE DIPSTICK. Drain the excess oil if too much has been added. T oo much oil can cause high oil consumption, high operating temperatures and oil foaming. T oo little oil can cause severe engine damage.
33 34 ! W ARNING ! W ARNING SP ARK PLUG MAINTENANCE AND REPLACEMENT Refer to the Speci fi cations for spark plug type and gap speci fi cations. Check and clean spark plugs every 200 hours. Replace plugs every 500 hours. T o prevent cross threading the spark plug, always thread it in by hand until it seats.
T roubleshooting The table below provides basic troubleshooting guidance. If you fail to resolve the problem after taking the corrective actions suggested, contact the equipment manufacturer or a Robin Subaru dealer . Many troubleshooting procedures present hazards that can result in severe personal injury .
37 38 Robin America has established the Robin Subaru Ful fi llment Center to take and ship orders to anyone wanting Robin Subaru reference material. This allows for the prompt ful fi llment of Robin Subaru part and service manuals, counter catalogs, price books and other support material to dealers and end users at the lowest possible price.
FEDERAL EMISSIONS COMPONENT DEFECT W ARRANTY EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE - This emission warranty is applic- able in all States, except the State of California Fuji Heavy Industries Ltd.
41 42 CALIFORNIA EMISSION CONTROL W ARRANTY ST A TEMENT YOUR W ARRANTY RIGHTS AND OBLIGA TIONS The California Air Resources Board and Fuji Heavy Industries Ltd. (herein "FUJI") are pleased to explain the emission control system warranty on your 2004 and later Small Off-Road engine (herein "engine").
(4) repairs performed outside of the authorized warranty service dealers (5) use of parts which are not authorized by FUJI. 2. Add-on or modified parts This warranty does not cover any part that malfunctions, fails or is damaged due to alter- ations by changing, adding to or removing parts from the engine.
How to remove the spark arrestor 1. Remove the fl ange bolts from the muf fl er cover and remove the muf fl er cover . 2. Remove the special screw from the spark arrestor and remove the spark arrestor from the muf fl er . Clean the spark arrestor screen Use a brush to remove carbon deposits from the spark arrestor screen.
INDUSTRIAL PRODUCTS DIVISION 4-410 Asahi, Kitamoto-shi Saitama, 364-851 1, Japan Phone +81(48) 593-7798 Fax +81(48) 593-7946 Web site http://www .fhi.co.jp/robin/ / 940 Lively Blvd. Wood Dale, IL 60191 U.S.A. Phone: 630-350-8200 Fax: 630-350-8212 Website: http://www .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Subaru Robin Power Products EH64 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Subaru Robin Power Products EH64 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Subaru Robin Power Products EH64 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Subaru Robin Power Products EH64 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Subaru Robin Power Products EH64, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Subaru Robin Power Products EH64.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Subaru Robin Power Products EH64. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Subaru Robin Power Products EH64 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
