Manuale d’uso / di manutenzione del prodotto 8050 del fabbricante Stovax
Vai alla pagina of 20
Brunel Mk III Conventional Flue With upgradeable control valve Instructions for Use, Installation and Servicing For use in GB, IE (Great Britain and Eire) PR0595 Issue 4 (August 2008) IMPOR T ANT Do not attempt to burn rubbish in this fire. This stove must only be operated with the door secured firmly in position.
2 CONTENTS COVERING THE FOLLOWING MODELS BRUNEL - 8050 - P8050 PAGE APPLIANCE COMMISIONING CHECKLIST 3 USER INSTRUCTIONS 4 INSTALLATION INSTRUCTIONS 8 Technical Specifications 8 Site Requirements 9 In.
3 FLUE CHECK PASS FAIL 1. Flue is correct for appliance 2. Flue flow test 3. Spillage test GAS CHECK 1. Gas soundness & let by test 2. Standing pressure test mb 3. Appliance working pressure (on High Setting) mb NB All other gas appliances must be operating on full 4.
4 USER INSTRUCTIONS 2.3 • Holdin for 5to 10seconds and thenrelease The pilot remains lit. If the pilot does not light, repeat the procedure.
5 4.2 • Holdin the controlknob androtate anti-clockwise until the knob is pointing at the ignition symbol ( ★ ) • Applya lightedmatch tothe pilothood, Diagram 3 3 AR0897 4.
6 USER INSTRUCTIONS AR0900 6 6.4 • Placethree coals equallyspaced onthe rear ofthe fuel bed so they touch the rear panel, Diagram 7 AR0901 7 6.
7 USER INSTRUCTIONS 9. 'RUNNING IN' 9.1 The surface coating on your GAZCO stove will ‘burn off’ during the first 24 hours of operation on high, producing a harmless and temporary odour. If the odour persists ask your retail for advice. 10.
8 INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION Covering the following models Brunel - 8050 - P8050 Model Gas Cat. Gas Type Pressure Nox Class Aeration Injector Gas Rate m 3 / h Input kW (Gros) Country Hoog Laag Brunel 8050 I 2H Natural Gas (G20) 20mbar 5 4 x 16 120 0.
9 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 1. FLUE AND CHIMNEY REQUIREMENTS 1.1 The chimney or flue system must comply with the rules in force, and must be a minimum of 127mm (5”) in diameter. The following are suitable for use with this appliance.
10 2.3 Having run the gas supply to the stove, PURGE THE SUPPLY PIPE, this is essential to expel any debris that may block the gas controls. • Connectthe gassupply tothe 8mm-compressionelbow at the RH rear corner of the stove, Diagram 3.
11 AR0886 4 2.7 • Placethe closure plateagainst thefireplace opening • • Ensurethere is sufficientoverlap aroundthe perimeter to allow a fume tight seal to be made • Cutstraight acrossthe topof theplate if trimmingis required 2.
12 3.5 • Placefive coals onthe frontof the fuelbed sothey rest on the front coal effect and lean against the vertical fingers, Diagram 9 AR0902 9 3.
13 INSTALLATION INSTRUCTIONS COMMISSIONING 1. COMMISSIONING 1.1 • Closeall openable doorsand windowsin the room • Ignitethe stoveand operateon maximum for10 minutes AR0539 1 If there is any doubt, run the stove for a further 10 minutes, and repeat the test.
14 IGNITION FUNCTIONAL CHECK 1 PILOT WILL NOT LIGHT Ensure there is no debris around the pilot assembly, (e.g. soot, etc.) which could short the spark, clean the area. Operate the valve. Is there a spark? Consult Section 2 and retry. Check alignment of pilot burner head, change the ignition lead, see diagram 1 on page 17.
15 SERVICING INSTRUCTIONS FAULT FINDING CHARTS PILOT WILL NOT STAY LIT OR FIRE GOES OUT IN USE Ensure there is no debris around the pilot assembly, e.g. coal, soot etc. which could short the spark, clean the area. Problem is with the pipework or fittings which lead to the fire.
16 3. IGNITION LEAD AND PIEZO Due to the method of manufacture, these components can only be replaced as an integral unit. 3.1 • Turnthe gas supplyoff atthe isolation d.
17 AR0320 3 • Prisethe smallretaining ringout ofthe inlet andremove the filter 4.2 • Replacewith a newfilter andpush into positionensuring that it sits on the shoulder • Replacethe retainingring andpush intoposition.
18 8. PRIMARY AERATION PLATE 8.1 • Turnthe gas supplyoff atthe isolation device. 8.2 To open the doors: • Slackenthe domednut onthe upperdoor and loosen the bolt from behind the latch 8.
19 SERVICE RECORDS 1ST SERVICE 2ND SERVICE Date of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date of Service: ................................. Next Service due: ............................... N e x t S e r v i c e d u e : .
Gazco Limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7JG Tel: (01392) 261999 Fax: (01392) 444148 E-mail: info@gazco.com A member of the Stovax Group.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stovax 8050 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stovax 8050 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stovax 8050 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stovax 8050 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stovax 8050, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stovax 8050.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stovax 8050. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stovax 8050 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
