Manuale d’uso / di manutenzione del prodotto MGD 221 MKII del fabbricante Barco
Vai alla pagina of 35
Inst allation & User Manual MGD 221 MKII Medical Greyscale Display V599327/Rev . 00 November 2001 BarcoView Theodoor Sevenslaan 106 8500 Kortrijk, Belgium Phone: +32(0)56 23 32 44 Fax: +32(0)56 23 33 74 E-mail: sales.medical@barco.com http://www .
MGD 221 User's Guide 3 © 2001 BARCO nv. All rights reserved. Trademark information TrueGrey, MediCal, BarcoMed, and MeDis are registered trademarks of BARCO NV.
MGD 221 User's Guide 4.
MGD 221 User's Guide 5 Regulations • This apparatus conforms to: IEC601-1, UL2601-1, cUL2601-1, EN 60601-1 • This apparatus is classified as Type B without Applied Part.
MGD 221 User's Guide 6.
MGD 221 User's Guide 7 CONTENTS 1. Introduction ..................................................................................................... 9 1.1 Overview .................................................................................
MGD 221 User's Guide 8.
Introduction 9 1. INTRODUCTION 1.1 Overview Resolution and bandwidths The BARCO MGD 221 is a high resolution, greyscale portrait display. Its outstanding visual performance, combining a 2 MegaPixel resolution with a high brightness, makes it ideal for medical imaging and many other medical and scientific applications.
Introduction 10 A lot of adjustments can also be done on the monitor itself, by means of an extensive on-screen menu system, accessible from the rear panel controls.
Installation 11 2. INSTALLATION 2.1 Precautions • Keep your original packaging. It is designed for this display and is the ideal protection during transport. • Do not lift the display all by yourself to avoid injury. • Avoid reflections in the picture tube to reduce eye strain.
Installation 12 2.3 Controls and connectors 1 {1} Optical sensor plug {2} Ambient Light Compensation (ALC) sensor (optional) {3} Green power LED {4} Control knob, combination of a push button and a turning knob. The control knob is used for switching the power on/off, and selecting and performing functions in the OSD (on-screen display) menu.
Installation 13 2.4 Signal connection a) Connection of video signals The connected equipment must comply to all relevant safety demands. Important: The use of low-quality video cables can distort the video signal and influence diagnosis. 1. Check the impedance of the imaging board that produces the video signals you want to connect.
Installation 14 b) Connection of data signals The display can be controlled remotely by a computer through the serial data bus. A typical example of this, is the MediCal software that controls the display. MediCal runs on a PC that is connected through the serial data bus.
Installation 15 d) Connection of power 1. Power cord: Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 300 V min., provided with a hospital-grade type plug 5-15P configuration for 120V application, or 6-15P for 240V application.
Installation 16 Important considerations • The best environment for diagnostic imaging is one with controlled and dimmed ambient light. The human eye's sensitivity depends on the ambient light strength. It is most sensitive to small contrast changes (or subtle image details) at limited ambient light levels.
Operation 17 3. OPERATION: USER CONTROLS Important : The best way to adjust and control the display is by using MediCal, which displays the ideal test patterns for correct adjustment. However, in case you do not dispose of MediCal, you can control and adjust the display by means of the built-in On-Screen Display (OSD).
Operation 18 3.2 Contrast and brightness control Contrast and brightness can be controlled through the OSD menus. To activate the OSD Turn the control knob {4} from left to right or from right to left. As a result, the OSD main menu appears. Note: The control knob should turn over at least 30 degrees before the OSD becomes visible.
Operation 19 To control contrast manually 1 Turn the control knob to select Contrast in the OSD main menu. 2 Press the control knob shortly. The contrast control menu appears. 3 In the contrast control menu, select Manual contrast adjustment and press the control knob shortly.
Operation 20 STATUS INFORMATION Display Name: MGD 221MKII Serial Number: 5114147 Mode Name: New mode Mode H-frequency: 48.32 kHz Mode V-frequency: 59.94 Hz Software Version: V 1.01 Run time: 50 hours White level: 215 cd/m2 Activity timeout 30s SH compensation OFF Actual H-frequency:72.
Operation 21 Software Version: The internal software version. Run time: The total operating time since production, including burn-in time. White level: The display’s white level or light output after calibration, in calibrated position.
Advanced 22 4. ADVANCED SETTINGS AND ADJUSTMENTS (FOR SERVICE STAFF ONLY) Important: The functions and controls described in this chapter can have a serious impact on the performance of the display. They should be touched by trained service staff only! 4.
Advanced 23 Explanation of the Settings menu items LUC: LUC is short for Luminance Uniformity Control. When switched on, the internal waveform processor will modulate the gain of the video amplifier so that the luminance is equal all over the screen (within a tolerance of +/- 5%).
Advanced 24 ADJUSTMENTS - Geometry - Focus - ALC - Luminance uniformity - Factory reset - Exit Adjustments menu 4.2 Adjustments a) How to make the adjustments 1 Turn the control knob at the rear from left to right or from right to left to activate the On-Screen Display (OSD) main menu.
Advanced 25 Width Horizontal position Height Vertical position Blanking - Blanking left Blanking - Blanking right Blanking - Blanking top.
Advanced 26 Interlacing - Pre correction In most cases you do not need to change this adjustment. You may need to increase this adjustment only when the connected video and sync signal contains an abn.
Advanced 27 SH Compensation: SH Position With SH Compensation on, we advise to use the SH Position control instead of the Horizontal Position control in the Geometry menu.
Advanced 28 Advanced geometry - Corner top right Advanced geometry - Corner bottom left Advanced geometry - Corner bottom right Advanced geometry - Linearity & S-correction - Horizontal linearity .
Advanced 29 Advanced geometry - Advanced bowing & skewing - Horizontal bowing left Advanced geometry - Advanced bowing & skewing - Horizontal bowing right Advanced geometry - Advanced bowing &.
Advanced 30 Focus Static focus Adjust Static focus to obtain an image as sharp as possible in the center. Focus zone You can adjust the focus in 9 independent zones. Turn the control knob to obtain an image as sharp as possible in the selected zone. Press the control knob to switch to the next zone.
Advanced 31 Luminance uniformity This menu allows you to calibrate the display, including the Luminance Uniformity circuit. Proceed as follows: 1 Connect the X-Rite DTP92 sensor and apply the black shield (see chapter "Installation"). 2 Follow the instructions on the screen.
Maintenance 32 5. MAINTENANCE Picture tube The glass panel of the picture tube is handled with a special coating. Take care not to damage or scratch the coating. Clean the picture tube with a soft woolen or cotton cloth. The cloth should be moist, not wet! Use a watery solution or a mild commercial glass cleaning solution.
Troubleshooting 33 6. TROUBLESHOOTING There appears no image on the picture tube, the green LED at the rear is out • Check if the power cord is properly connected to the power outlet and to the display.
Background information 34 APPENDIX A: BACKGROUND INFORMATION Luminance Uniformity Correction A characteristic (or limitation) of every picture tube (CRT) is that the luminance decreases towards the edge of the screen surface. The decrease is normally 20 to 30 %.
Background information 35 When you leave the computer idle for a longer period, the imaging board now delivers horizontal sync only. As a result, the display's micro controller switches off a number of internal circuits. The power consumption has now dropped with about 42 %.
Technical specifications 36 APPENDIX B: TECHNICAL SPECIFICATIONS Picture tube: Faceplate transmission: No Panel: +/- 34% AR panel: 30% Faceplate type: AR panel or No Panel Image representation: portrait Phosphor: B4-L8 Light output: Calibrated: 215 Cd/m² Resolution: Max.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Barco MGD 221 MKII è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Barco MGD 221 MKII - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Barco MGD 221 MKII imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Barco MGD 221 MKII ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Barco MGD 221 MKII, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Barco MGD 221 MKII.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Barco MGD 221 MKII. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Barco MGD 221 MKII insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
