Manuale d’uso / di manutenzione del prodotto HDX Series del fabbricante Barco
Vai alla pagina of 30
T op & Bott om C ar ry Handle Install ation manual For H DX se rie s R9864060 R9864070 R9864080 R5905106/00 28/06/2011.
Barco nv E vents Noordlaan 5, B-8 520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.88.24 Support: www.barco.com/esupport Visit us at the web: www.barco.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
.
Tabl e of c ont ents T ABLE OF C ONTEN TS 1 . I n t r o d u c t i o n ... .... ...... .... .... ...... .... .... ...... .... .... ...... .... .... .... ...... .... .... ...... .... .... ...... ... 3 1.1 T op Carry Handle . . . ............... ........
Tabl e of co nt ents 2 R5905106 TOP & BOTTOM CA RRY HANDLE 28/06/2011.
1. Introdu ction 1. INTROD UCTION Purpose of the T op & Bottom Carry Handles The T op & Bottom Carry Handles are ex clusively designed for t he Barco HDX series and can thus not be used on any other equip- ment.
1. Introduc tion 1.1 T op Carry Handle Order info & conte nt of the kit When ordering the T op Carry Handle for HDX series, refer to artic le number R9864060.
1. Introdu ction 1.2 Bottom Carry Handle Order info & conte nt of the kit When ordering the Bottom Carry Handle for HDX series, refer to arti cle number R9864070.
1. Introduc tion 1.3 T ouring kit Order info & conte nt of the kit When ordering the T ouring kit for HDX series, refer to articl e number R9864080.
2. Installation pr ocedur es 2. INST A LLA TION PR OCEDURES Overview • Installing the Bottom Carry Ha ndle • Removing the Bottom Carry Handle • Installing the T op Carry Handle • Removing the .
2. Inst allation pr ocedure s 2.1 Install ing the Bottom Carry Handle Necessary t ools 17 mm open-end wrench How to install the Bottom Carry Handle? 1. Turn the project or upside down and remove the 4 feet (reference 1, image 2-1) by turning them anticlockwise.
2. Instal latio n proced ures 6 Image 2-3 5. Bring the stacking points back to their original position by turning them clockwise. R5905106 TOP & BOTTOM CA RRY HANDLE 28/ 06/2011 9.
2. Inst allation pr ocedure s 2.2 Removing the Bot tom Carry Handle How to remove the Bott om Carry Handle? 1. Remov e the 4 bolts (reference 6, im age 2-4). 6 Image 2-4 2. Remov e the Bottom Carry Handle fr om the projector (image 2-5). Image 2-5 3. Install the 4 feet by turning them c lockwise (image 2-6).
2. Instal latio n proced ures Image 2-6 R5905106 TOP & BOTTOM CA RRY HANDLE 28/ 06/2011 11.
2. Inst allation pr ocedure s 2.3 Installing the T op Carry Handle Necessary t ools 8 mm A llen wrench How to install the T op Carry Handle? 1. Position the T op Carry Handle on top of the projector so that the fi xati on holes match the holes in the projector .
2. Instal latio n proced ures 2.4 Removing the T op Carry Handle Necessary t ools 8 mm A llen wrench How to remove the T op Carry Handle? 1. Turn out the 4 bolts (r eference 1, image 2-8) and remove the 4 washers. 1 1 Image 2-8 2. Remov e the T op Carry Handle from the p rojector .
2. Inst allation pr ocedure s 2.5 Allowed projector positions C AUTION : Using the projector in a disallowed positi on can cause premature lamp failure. Which projector positions are allowe d? With both the T op Carry Handle and Bottom Carry Handle installed, t he projector can be placed in s everal positions.
2. Instal latio n proced ures 1. Press Menu to acti vate the menus and select Service → Diagnos is → Tilt sensor . Image 2-10 Image 2-1 1 Image 2-12 2. Press EN TER to read out the t ilt sensor . Image 2-13 The rotation of the projec tor is visually displayed.
2. Inst allation pr ocedure s 2.6 Stacking project ors The procedure below describes how to stack 2 projectors. The procedu re to stack 3 pr ojectors is analog. W ARNING : Never stack more than three (3) projectors. Failure to do so can cause serious i njury or death.
2. Instal latio n proced ures Image 2-15 4. Lock the stacking points by rotating t he ring a quarter t urn clockwise while pushing it downwards until the ring it clicks in (im- age 2-16).
2. Inst allation pr ocedure s 2.7 Suspending the projector from a truss W ARNING : Never suspend more than two (2) projectors. F ailure to do so can cause serious injury or death. Introduction A projector can be suspended from a tr uss using rigging clamps.
2. Instal latio n proced ures X mm 1 1 Image 2-19 3. Mount the rigging clamps on t he rigging points: a) Screw the nut (r eference 2, i mage 2-20) on the spacer (refer ence 3, image 2-20) to the des ired height. b) Install t he spacer in the r igging point by turning it clockwise until t he nut and the r igging point meet.
2. Inst allation pr ocedure s Image 2-21 6. Lock the 4 rigging clamps by turning the fi xation knob clockwise. Image 2-22 7. Install the 2 safety cables. Wind them a round the carry handle and the truss (push the hook through the loop and then around the truss).
2. Instal latio n proced ures Image 2-23 8. Lift up the truss with projector to the desired height. Warning: Make sure the s afety cable is installed with a minimum of play , so that the projector can only fall down for maximum 20 cm. If necessary , wind the cable a few times around the truss before clasping the safety hook around the cable.
2. Inst allation pr ocedure s Image 2-24 Securi ty cables, mount Warning: Always use 2 safety cables to secure a stacked projector in a hanging con fi guration. 3. Suspend the stack from the tr uss as described in "Suspending the projector f rom a truss", page 18.
2. Instal latio n proced ures 2.8 Skewing the projector How to skew the projector? 1. Turn the adjustment knob cl ockwise or anticlockwise to skew the projector as il lustrated.
2. Inst allation pr ocedure s 2.9 Inclinating and/or rotating the projector How to inclinate and/or rotate the projector? 1. Turn the proj ector feet in or out to inclinate and/or rotate t he projector as needed.
2. Instal latio n proced ures 2.10 Aligning stacked projectors How to align stac ked project ors? 1. Project a hatch pattern with the reference projector .
2. Inst allation pr ocedure s 2.1 1 Dimensions T op Carry Handle 685 575 Image 2-29 Dimens ions give n in m illimete rs Bottom Carry Handle 825 685 575 435 200 174 174 160 96 96 Image 2-30 Dimens ions.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Barco HDX Series è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Barco HDX Series - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Barco HDX Series imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Barco HDX Series ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Barco HDX Series, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Barco HDX Series.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Barco HDX Series. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Barco HDX Series insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
