Manuale d’uso / di manutenzione del prodotto DS06 del fabbricante Stanley Black & Decker
Vai alla pagina of 26
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 34566 2/2015 V er . 10 DS06 HYDRAULIC DIAMOND SA W USER MANUAL Safety , Operation and Maintenance.
2 ► DS06 User Manual DECLARATION OF CONF ORMI TY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONFOR MITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFORM ITA Hydraulic Tools _______ ______.
DS06 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► DS06 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
DS06 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► DS06 User Manual • Always be well rested and mentally alert before op- erating the chain saw . • Do not allow bystanders near the chain saw when starting or cutting. • Do not start cutting until you have a clear work area and secure footing.
DS06 User Manual ◄ 7 SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
8 ► DS06 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
DS06 User Manual ◄ 9 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
10 ► DS06 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
DS06 User Manual ◄ 1 1 PRE-OPERTION PROCEDURES CHECK THE POWER SOURCE 1. Using a calibrated ow meter and pressure gauge, make sure the hydraulic power source develops a ow of 7–9 gpm/26–34 lpm for the 8 gpm model and 4–6 gpm/15–23 lpm for the 5 gpm model at 2000 psi/140 bar .
12 ► DS06 User Manual ing the maximum clearance increases the chance of the chain being dislodged from the bar groove. 2. Make sure the bar attaching nuts are fully tightened and the chain guard is in place. Max 5/16" Bottom of Bar Figure 3. Maximum Chain Clearance CHECK CHAIN SEGMENT WEAR 1.
DS06 User Manual ◄ 13 DOWN CUT PLUNGE CUT UP CUT Figure 6. T ypes of Cuts (chain guard removed for clarity) 1. Do not use a cutting force in excess of 45 lbs/20 kg. Excessive force causes the chain to slow down or stall and causes premature wear of the saw bar and chain.
14 ► DS06 User Manual GENERAL MAINTENANCE TIPS Several simple maintenance tasks which, if performed, can keep a chain saw operating at a high level of ef- ciency . Routine maintenance also keeps replacement costs down on the parts of the chain saw , which occa- sionally wear out.
DS06 User Manual ◄ 15 Max 5/16" Bottom of Bar Figure 1 1. Exposed Drive Link T ang SER VICING THE CHAIN The following procedures explain how to break a chain using Stanley’s bench mounted chain breaker (P/N 20858) to remove a worn or damaged segment.
16 ► DS06 User Manual REPLACING THE CHAIN BREAKER PUNCH If the chain breaker punch (P/N 22801) becomes worn or damaged, use the following procedures for replace- ment. 1. Remove the punch by loosening the set screw (Figure 16). Figure 16. Removing the Punch 2.
DS06 User Manual ◄ 17 5. Apply a few drops of oil to the rivet hub (Figure 22). Figure 22. Applying the Oil 6. T urn the spinner crank while slowly running the take- up handle inward (approximately one full revolution) until the rivet head is formed (Figure 23).
18 ► DS06 User Manual 6. With the bar and rivets solidly supported on a strong at steel surface, carefully peen the rivet heads down with the at end of a hammer . Be careful to only hit the rivet head. Do not hit the bar body; this will pinch the nose sprocket.
DS06 User Manual ◄ 19 • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy- draulic system.
20 ► DS06 User Manual If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the tool, always check that the hydraulic power source is supplying the cor- rect hydraulic ow and pressure to the tool as listed in the table.
DS06 User Manual ◄ 21 SYMPTOM CAUSE SOLUTION No water discharge at bar . Blocked port(s) in bar . T urn off hydraulic supply . Remove bar and chain and clean bar thoroughly . Blow ports with compressed air . Blocked inlet or outlet. T urn off hydraulic supply .
22 ► DS06 User Manual Cutting Depths ................................................................................................................................... 13 inches/33 cm Bar Lengths ....................................................
DS06 User Manual ◄ 23 54 DS06 P ARTS ILLUSTRA TION.
24 ► DS06 User Manual ITEM P ART NO. QTY DESCRIPTION 1 00753 8 HSHCS 10-24 UNC × 1-1/4 2 73659 1 NAME T AG 3 1 1207 1 CIRCUIT D DECAL (8-GPM MODEL) 1 1206 CIRCUIT C DECAL (5-GPM MODEL) 4 07652 1 RE.
DS06 User Manual ◄ 25 ITEM P ART NO. QTY DESCRIPTION 85 17134 1 NUT , 1/4 -20 HHD L T SST 86 31614 1 SPIROL PIN 87 30635 1 SPIROL PIN, 5/16 × 7/8 88 28409 1 COMPOSITE DECAL (CE) 89 1 1212 1 SOUND P.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stanley Black & Decker DS06 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stanley Black & Decker DS06 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stanley Black & Decker DS06 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stanley Black & Decker DS06 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stanley Black & Decker DS06, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stanley Black & Decker DS06.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stanley Black & Decker DS06. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stanley Black & Decker DS06 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
