Manuale d’uso / di manutenzione del prodotto CT06 del fabbricante Stanley Black & Decker
Vai alla pagina of 20
© 2010 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 58543 7/201 1 V er . 3 S afety , O pera tiOn and M aintenance USer ManUaL CT06 1650 PSI HYDRAULIC CRIMPING T OOL.
.
CT06 User Manual ◄ 3 T ABLE OF CONTENTS SERVICING THE ST ANLEY HYDRAULIC CRIMPING TOOL. This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► CT06 User Manual SAFETY SYMBOLS Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
CT06 User Manual ◄ 5 SAFETY PRECA UTIONS T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety .
6 ► CT06 User Manual T OOL STICKER & T AGS SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
CT06 User Manual ◄ 7 HOSE TYPES The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► CT06 User Manual HOSE RECOMMEND A TIONS Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber.
CT06 User Manual ◄ 9 HTMA REQUIREMENTS TOOL CA TEGOR Y HYDRAULIC SYSTEM REQUIREMENTS TYPE I TYPE II TYPE III TYPE RR FLOW RA TE 4–6 gpm (15–23 lpm) 7–9 gpm (26–34 lpm) 1 1–13 gpm (42–49 lpm) 9–10.
10 ► CT06 User Manual OPERA TION Open-Center (no gap) Adapter Cylinder T rigger Handle T op View of T ool Figure 2. OC/CC Setup 2. Loosen the 2 setscrews on the cylinder . 3. T urn the adapter until it stops: • Counter clockwise (CCW) to change to closed center (creates gap) • Clockwise (CW) to change to open center (clos - es gap) 4.
OPERA TION CT06 User Manual ◄ 1 1 1. If the hydraulic hoses are connected: • T urn the hydraulic system control valve OFF . • Disconnect rst the hydraulic input (supply) hose, then the output (return) hose. 2. Clean the surfaces of the die holder to remove any dirt or grease.
OPERA TION 12 ► CT06 User Manual NOTE: If the uncoupled hoses are left in the sun, pressure increase within the hoses can make them difcult to connect.
OPERA TION CT06 User Manual ◄ 13 7. Release the trigger to retract the nibs. 8. Repeat the crimp as required. 9. After the last crimp, make sure the nibs in the crimp- ing head are fully retracted 10. Pull out the latch pin and rotate the latch away from the crimping head.
14 ► CT06 User Manual T OOL PRO TECTION & CARE • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hy- draulic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hydraulic system.
CT06 User Manual ◄ 15 TR OUBLESHOO TING If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the crimping tool, always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the grinder as listed in the table.
16 ► CT06 User Manual SPECIFICA TIONS Capacity ................................................................................... #10-750 MCM Aluminum and #10-500 MCM Copper Crimping Force ...........................................................
CT06 User Manual ◄ 17 CT06 P ARTS ILL USTRA TION.
18 ► CT06 User Manual CT06 P ARTS LIST ITEM NO. P ART NO. QTY DESCRIPTION 1 001 14 1 ROLL PIN 2 001 18 1 RET AINING RING 3 00144 12 HSHCS 4 07626 2 O-RING ■ 5 09330 1 O-RING ■ 6 00294 1 O-RING .
.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 503-659-5660 / Fax 503-652-1780 www .stanleyhydraulic.com IMPORT ANT T o ll out a Product Warranty Recording form, and for information on your warranty , visit Stanleyhydraulic.com and select the W arranty tab.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stanley Black & Decker CT06 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stanley Black & Decker CT06 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stanley Black & Decker CT06 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stanley Black & Decker CT06 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stanley Black & Decker CT06, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stanley Black & Decker CT06.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stanley Black & Decker CT06. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stanley Black & Decker CT06 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
