Manuale d’uso / di manutenzione del prodotto MIGHTYLAM 2700 del fabbricante Banner American Products
Vai alla pagina of 22
OPERATING INSTRUCTIONS MIGHTYLAM 2700 ROLL LAMINATOR.
2 TABLE OF CONTENTS Safety Messages and Electrical Safeguards ..................... .........3 - 4 Introduction ........................ ..................... ..................... .................... Laminator Features . ............................
3 IMPORTANT SAFETY MESSAGES AND ELECTRICAL SAFEGUARDS For your protection, do not connect the laminator to electrical power or attempt to operate it until you read these instructions completely. Keep these instructions in a convenient location for future reference.
4 If the below conditions exist do not attempt to service or repair the laminator yourself. Unplug the laminator from the electrical outlet and contact an authorized service representative. • When the power supply cord or plug is damaged or frayed.
5 INTRODUCTION Congratulations on your purchase of the MightyLam 2700 Roll Laminator. This unit is designed to provide years of trouble-free service. The MightyLam 2700 will accept rolls of laminating film up to 27” wide in all film thicknesses. Paper and card stock up to 1/16” (1.
6 INITIAL SETUP Unpacking... Before unpacking the unit, inspect the shipping container for signs of damage. Notify the carrier and your dealer immediately if any damage is noted. Components... Figure 1 below shows the location of the major components and controls of the MightyLam 2700.
7 OPERATING INSTRUCTIONS Heat Control Your new MightyLam 2700 has digital heat controllers for each heat shoe. Users can easily adjust the set temperature for each heat shoe individually to achieve the best quality lamination. Both controllers have been calibrated to accurately display the heat shoe temperature in the laminating range.
8 OPERATION This section describes the operation of your MightyLam 2700. This laminator is designed for all widths of plastic up to 27”. However, if narrower widths are used the Heat Shoes must be cleaned before using a wider roll. Refer to the MAINTENANCE section for cleaning instructions.
9 4. Pull 6”-12” of film from the bottom roll. Pass it under the lower idler bar. You can “d rop-down” the lower idler bar to give you more clearance. After doing so, return the idler bar to its upper position for running the machine. Drape the film from the bottom roll over the film from the top roll.
10 Adjusting Mandrel/Film Tension….. Each type of laminating film has different characteristics a nd may require laminator adjustment. The tensi on should be set so that the film moves over the heat shoes without wrinkles as the film enters the laminator.
11 Caution! If the blade release knobs are turned too far, the slitter blade may fall out of its guide and come in contact with the rubber rollers. If this happens, the rollers could be damaged. Never turn the blade release knobs m ore than one turn to position the blades.
12 Note : You may want to run a test lamination first as any item that passes between the heat shoes will be laminated and cannot be recovered un til it exits the rear of the laminator. 5. Additional items may be fed in sequence, k eeping enough distance between sheets for trimming.
13 Mounting your print: 1. Be sure all laminator parts (i.e. safety shield, feed tabl e, etc.) are in their proper positions and the lam inating film is loaded correctly on top and bottom m andrels.
14 TROUBLESHOOTING PROBLEM: Laminator is inoperative. Moto r does not run, indicator lights are out. ACTION: Unit may be unplugged. Connect power suppl y. Ensure that your circuit breaker has not tripped. Fuse m ay have blown. Replace 15 amp power fuse.
15 MAINTENANCE This section contains instructions for cleaning and mainta ining your lam inator. These procedures should be preformed at regular intervals to help ensure the trouble-free operation of your lam inator. Cleaning the Heat Shoes and Laminating Rollers.
16 WARRANTY AND RETURN POLICY Warranty Your laminator is warranted to be free of def ects in material and workmanship for a period of 1 year from the original purchase date. In the ev ent of a defect in material or workmanship, the manufacturer or its authorized dealer, will repair or replace (at their option) the laminator.
17 PARTS LIST AND ILLUSTRATIONS This section contains refere nce d rawings and a par tial parts list to assist you wh e n ordering parts for your laminator.
18 43 10103 TABLE, FEED 1 44 11539 SUPPORT, RIGHT SIDE 1 45 11538 SUPPORT, LEFT SIDE 1 46 503 SPACER WASHER 8 47 1319 LIGHT,INDICATOR,RED 120V 1 48 11095 SWITCH, RED (HEAT) 1 49 11094 SWITCH, GREEN (M.
19.
20.
21.
22.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Banner American Products MIGHTYLAM 2700 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Banner American Products MIGHTYLAM 2700 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Banner American Products MIGHTYLAM 2700 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Banner American Products MIGHTYLAM 2700 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Banner American Products MIGHTYLAM 2700, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Banner American Products MIGHTYLAM 2700.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Banner American Products MIGHTYLAM 2700. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Banner American Products MIGHTYLAM 2700 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
