Manuale d’uso / di manutenzione del prodotto SY-6BA+ IV del fabbricante SOYO
Vai alla pagina of 103
SY-6BA+ IV Motherboard **************************************************** Pentiu m ® III, Pentiu m ® II & Celeron Processor supported 82440 BX AGP/PCI Motherboard 66 & 100 MHz Front Si.
SOY O ™ SY-6BA+ IV ii Copyright © 1999 by Soyo Computer Inc. Trademarks: Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of their owners. Product Rights: All names of the product and corporate mentioned in this publication are used for identification purposes only.
T able of Contents SY-6BA+ IV iii Table of Contents CHAPTER 1 MOTHERBOA RD DESCRIPTION ............................. 1 1-1 INTRODUCTION ........................................................... 1 1-2 KEY FE A TURES ..................................
T able of Contents SY-6BA+ IV iv 3-1 SOYO COMBO SETUP ................................................ 54 3-2 STANDARD CMOS SE TUP ......................................... 61 3-3 BIOS FE A TURES SETUP ............................................. 64 3-4 CHIPSET FE A TURES SETUP .
Motherboard Description SY-6BA+ IV 1 Chapter 1 MOTHERBOARD DESCRIPTION 1-1 INTRODUCTION The SY-6BA+ IV AGP/PCI Motherboard is a high-performance Slot 1 supported A TX form-factor system board. SY-6BA+ IV uses the Inte l ® Chipset technology and supports Slot 1 class processors.
Motherboard Description SY-6BA+ IV 2 n CPU Multiplier The SY-6BA+ IV supports a wide range of multipliers: 2.0x, 2.5x, 3.0x, 3.5x, 4.0x, 4.5x, 5.0x, 5.5x, 6.0x, 6.5x, 7.0x, 7.5x and 8.0x n CPU Core Voltage The CPU Core voltage is set automatically according to CPU needs.
Motherboard Description SY-6BA+ IV 3 capable of transferring data up to 66 Mbytes/sec (IDE DMA Mode 4). n Wake-On-LAN Supports W ake-On-LAN (Some advanced network cards can wake the system up over the network, the WOL connector is provided by the SY-6BA+ IV to support this function) .
Motherboard Description SY-6BA+ IV 4 Ø COMPLIANCE The SY-6BA+ IV complies with all important industry standards. The following underlines the reliability of the SY-6BA+ I V , a motherboard to trust.
Motherboard Description SY-6BA+ IV 5 1-3 HANDLING THE MOTHERBOARD T o a void damage to your M otherboard, follo w these simple rules w hile unpacking: Ø B efore handling the M otherboard, ground yourself b y grasping an unpainted portion of the s y stem's meta l chassis.
Motherboard Description SY-6BA+ IV 6 1-5 SY-6BA+ IV MOTHERBOARD L AYOUT Back Panel SY-6BA+ IV Platform COM 1 COM 2 PRT USB 1 USB 2 PS/2 K B Connecto r PS/2 Mouse Connector JP1 0 PCI Slot # 1 PCI Slot .
Motherboard Description SY-6BA+ IV 7 1-6 SY-6BA+ IV MOTHERBOARD COMPONENTS ® ® 1 ® 8 2 8 A C A B C D E G H I J K L M N O P Q R S T U V W X Y Z A A A B F.
Motherboard Description SY-6BA+ IV 8 A A T X Po w e r Suppl y C onnector B Slot 1 C onnector C Po w er On b y K e yboard Jumper D C P U multiplier release Jumper E Inte l 82440 B X PC I / AGP Set F C .
Motherboard Description SY-6BA+ IV 9 1-7 MICROPROCESSOR T he motherboard supports a single Slot 1 processor. T he processor ’ s VID pins automaticall y program the voltage regulator on the motherboard t o the required processor voltage. In addition, the front side bus speed (66 MHz and 100 MH z) is automaticall y selected.
Motherboard Description SY-6BA+ IV 10 t w o, three, or four sockets. U s ing the serial presence detect (SP D ) data structure, programmed into an E² PRO M on the D IM M , the B IOS can determine the SDRA M ’ s size and speed. M inimum D IM M memor y size is 8 MB; m aximum D IM M memor y s ize is 25 6 MB .
Motherboard Description SY-6BA+ IV 11 1-8.3 ECC Memory EC C m emor y detects multipl e - bit errors and corrects singl e - bit errors. W he n EC C m emor y is installed, the BIOS supports both ECC and no n - EC C mode. EC C mode is enabled in the Setup program.
Motherboard Description SY-6BA+ IV 12 l A . G . P. in terface Ø Complies wi t h the A . G . P. specification Ø Support for +3.3 V A . G . P. - 66 / devices Ø Synchronous coupling to the hos t - bus.
Motherboard Description SY-6BA+ IV 13 Ø Complies wi t h the PC I specification Ø F ul l I S A bus support l U S B controller Ø Two U S B ports Ø Support for legac y k e yboard and mouse Ø Support.
Motherboard Description SY-6BA+ IV 14 Specifications, R e v 2.1, is independent of the PC I bus and is intended for e x clusive use wi t h graphica l di sp l a y d e vices.
Motherboard Description SY-6BA+ IV 15 1-9.5 IDE Support The motherboard has two independent ATA 33 and two independent ATA 66 bus-mastering PCI IDE interfaces. These interfaces support PIO Mode3, PIO Mode 4, AT API devices (e.g., CD-ROM), and Ultra DMA/33 (IDE1, IDE2) or Ultra DMA/66 (IDE3, IDE4) synchronous-DMA mode transfers.
Motherboard Description SY-6BA+ IV 16 recognize it as both the A and B drive 1-9.6 Real-Time Clock, CMOS SRAM, and Battery T he rea l - time cloc k is compa tible wi t h DS 1287 and MC 146818 components. T he cloc k provides a tim e - o f - d a y cloc k and a mul ticentury calendar wi t h a l ar m features and centur y rollover.
Motherboard Description SY-6BA+ IV 17 l B i - directiona l (P S / 2 compatible) l B i - directiona l E P P . A driver from the peripheral manufacturer is required for operation.
Motherboard Description SY-6BA+ IV 18 1-11 HARD WARE MONITOR T he optiona l hard w are monitor subsyste m provides l o w - cost instrumentation capabilities.
Hardware Installation SY-6BA+ IV 19 Chapter 2 HARDWARE INSTALL ATION Congratulations on your purchase of SY-6BA+ IV M otherboard. Y ou are about t o install and connect your n e w M otherboard. Note: D o not unpack the M otherboar d from its protective ant i - static packaging until you have made the foll o wing preparations.
Hardware Installation SY-6BA+ IV 20 2-2 UN PACKING THE MOTHERBOARD W he n unpacking the M otherboard, chec k for the foll o wing items: u T he S Y - 6B A + I V 82440 B X AGP / PC I M otherboard u T he.
Hardware Installation SY-6BA+ IV 21 2-3 INS TALLATION GUIDE W e will no w begin the installation of the M otherboard. Please follo w the ste p - b y - step procedure designed t o le a d you to a complete and correct installation.
Hardware Installation SY-6BA+ IV 22 2-3.1 CPU Installation Y our S Y - 6B A + I V motherboard comes wi t h a C P U retention set kit. T he retention set is used to hold the processor attached to the Slot 1 CP U connector on the motherboard.
Hardware Installation SY-6BA+ IV 23 1. Open the two sides by folding them up. 2. Push the locks on top of the CPU inward..
Hardware Installation SY-6BA+ IV 24 3. Insert the CPU into the retention module. The CPU fits in the CPU slot in only ONE way, do not try to force it in. 4. After completely inserting the CPU, push the two locks on top of the CPU outward. Now your CPU is ready for use.
Hardware Installation SY-6BA+ IV 25 Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat dissipation. Failing to install these items may result in overheating and possible burn-out of your CPU. 2-3.1.1 CPU Fan Installation Y our Slot 1 processor kit comes wi t h a cooling fan.
Hardware Installation SY-6BA+ IV 26 2-3.2 SDRAM Memory Module Installation Y our board comes wi t h four D IM M sockets, providing support for up t o 512 M b y tes or 1 GB ( wi t h registered D IM M s) . For 6 6 MHz front side bus C P U s use 12ns or faster memory; for 10 0 MHz front side bus C P U s use 8ns (10 0 MH z, P C 100 compliant) memor y .
Hardware Installation SY-6BA+ IV 27 Number of Memory Modules DIMM 1 DIMM 2 DIMM 3 DIMM 4 1 1 st 2 1 st 2 nd 3 1 st 2 nd 3 rd 4 1 st 2 nd 3 rd 4 th RAM Type SDRA M Memory Module Size (MB) 8 / 1 6 / 32 / 6 4 / 12 8 / 256 M b y tes Note: (1) 256 MB memory modules available on PC registered DIMM only.
Hardware Installation SY-6BA+ IV 28 IDE 1 IDE 4 IDE 2 IDE 3 1 1 1 1 ATA 3 3 ATA 6 6 2-3.3 Motherboard Connector 2-3.3.1 IDE Device Installation (HDD, CD-ROM) T he 6B A + I V comes wi t h four ID E connectors, wi t h support for up to 8 ID E D evices.
Hardware Installation SY-6BA+ IV 29 1 1 3 9 3 9 40-pi n ATA 6 6 Flat Cabl e 80-Conducto r.
Hardware Installation SY-6BA+ IV 30 2-3.3.2 Floppy Drive Installation T he s y ste m supports 5 possible flopp y drive types: 720 KB, 1.2 MB , 1.44 MB , 2.88 MB , and LS - 120. In addi tion, this M otherboar d supports a 3 - mode (72 0 K B / 1. 2 MB / 1.
Hardware Installation SY-6BA+ IV 31 2-3.3.3 Front Panel Connections Plug the computer case's front panel devices to the corresponding headers on the Motherboard.
Hardware Installation SY-6BA+ IV 32 2. Reset Plug the Reset push-button cable into the 2-pin Reset header on the Motherboard. Pushing the Reset button on the front panel will cause the system to restart the boot-up sequence. 3. Speaker Attach the 4-pin PC speaker cable from the case to the Speaker header on the Motherboard.
Hardware Installation SY-6BA+ IV 33 5. IDE LED Attach the 2-pin IDE device LED cable to the corresponding IDE LED header on the Motherboard. This will cause the LED to lighten when an IDE (HDD, CD-ROM) device is active.
Hardware Installation SY-6BA+ IV 34 2-3.3.4 Back Panel Connections All external devices such as the PS/2 keyboard, PS/2 mouse, printer, modem, USB can be plugged directly onto the Motherboard back panel. Only after you have fixed and locked the Motherboard to the computer case can you start connecting the external peripheral devices.
Hardware Installation SY-6BA+ IV 35 1. Onboard Serial Ports COM1/COM2 External peripherals that use serial transmission scheme include: - serial mouse, - and modem. Plug the serial device cables directly into the COM1/COM2 9-pin male connectors located at the rear panel of the Motherboard.
Hardware Installation SY-6BA+ IV 36 5. Universal Serial Bus USB1/USB2 This Motherboard provides two USB ports for your additional devices. Plug the USB device jack into the available USB connector USB1 or USB2. - Standard device drivers come with the Win98 for commonly used USB devices.
Hardware Installation SY-6BA+ IV 37 2-3.3.5 Other Connections 1. Wake-On-LAN (WOL) Attach the 3-pin connector from the LAN card which supports the W ake- On-LAN (WOL) function to the JP44 header on the Motherboard. This WOL function lets users wake up the connected computer through the LAN card.
Hardware Installation SY-6BA+ IV 38 2. Infrared (IR1) Plug the 5-pin infrared device cable to the IR1 header. This will enable the infrared transfer function. This Motherboard meets both the ASKIR and HPSIR specifications. Please install according to the following pin assignment: 3.
Hardware Installation SY-6BA+ IV 39 4. Cooling Fan Installation (1) CPU Cooling Fan After you have seated the CPU properly on the processor , attach the 3-pin fan cable to the CPUFAN connector on the Motherboard. The fan will stop when the system enters into Suspend Mode.
Hardware Installation SY-6BA+ IV 40 (2) Chassis Cooling Fan Some chassis also feature a cooling fan. This Motherboard features a CHAFAN connector to provide 12V power to the chassis fan. Connect the cable from the chassis fan to the CHAFAN 3-pin connector.
Hardware Installation SY-6BA+ IV 41 2-3.3.6 AGP VGA Card Insert the AGP VGA card into the AGP slot. Then connect the monitor information cable to the AGP card back plane external connector. Follow the manufacturer's instructions to perform the AGP VGA drivers installation.
Hardware Installation SY-6BA+ IV 42 2-3.3.8 A TX Power Supply Plug the connector from the power directly into the 20-pin male A TX PW connector on the Motherboard, as shown in the following figure.
Hardware Installation SY-6BA+ IV 43 3.3 V -12 V GN D PS-O N GN D GN D GN D -5 V 5V 5V 3.3V 3.3V GN D 5V GN D 5V GN D PW-O K 5VS B 12V ATX Powe r This motherboard requires a power suppl y , that meets the A TX 2.03 specifications. Make sure the power supply can support at least 720mA on the 5V Standby lead.
Hardware Installation SY-6BA+ IV 44 Step 3. CPU multiplier release Jumper: (JP8) Closing JP8 can make higher multiplier settings available on some INTEL CPUs.
Hardware Installation SY-6BA+ IV 45 Step 4. Power-On by Keyboard Jumper (JP10) You can choose to enable the Power-On by Keyboard function by shorting pin 1-2 on jumper JP10, otherwise, short pin 2-3 to disable this function. Power-On by Keyboard Enable Disable JP10 Setting Short pin 1-2 to enable the Power- On by Keyboard function.
Hardware Installation SY-6BA+ IV 46 2-3.6 Power On You have now completed the hardware installation of your Motherboard successfull y . 1. Turn the power on 2.
Hardware Installation SY-6BA+ IV 47 2-3.7 Quick BIOS Setup This Motherboard does not use any hardware jumpers to set the CPU frequenc y . Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP] . The [SOYO COMBO SETUP] menu combines the main parameters that you need to configure, all in one menu, for a quick setup in BIOS.
Hardware Installation SY-6BA+ IV 48 (2) CPU Frequency Available [CPU Frequency] settings on your SY-6BA+ IV Motherboard are detailed in the following table. CPU Frequency (MHz) Manual 350MHz (100 x 3.5) 266MHz (66 x 4 ) 400MHz (100 x 4 ) 300MHz (66 x 4.
Hardware Installation SY-6BA+ IV 49 (c) AGP Clock This option allows you to manually adjust the AGP host bus clock frequency to a value determined as a fraction of the CPU host clock. For example: With a CPU front side bus of 100MHz, [Auto] sets à When [auto] is selected and the (FSB Frequency) is less then 100MHz, it will be divided by [/ 1].
Hardware Installation SY-6BA+ IV 50 2-3.8 Troubleshooting at First Start l What should I do if the Motherboard refuses to start? 1. Check that all DIMM memory modules are inserted completel y . Sometimes a DIMM that is not inserted properly can cause boot problems.
Hardware Installation SY-6BA+ IV 51 2. Set the JP8 and JP9 to short if you use a FSB 66MHz CPU 3. Press and hold down the <Insert> key while turning on the system power. Keep holding down the <Insert> key until you see the message of the CPU type and frequency shown on the screen.
BIOS Setup Utility SY-6BA+ IV 52 Chapter 3 BIOS SETUP UTILITY This Motherboard's BIOS setup program uses the ROM PCI/ISA BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. After the diagnostic checks, press the [Del] key to enter the Award BIOS Setup Utilit y .
BIOS Setup Utility SY-6BA+ IV 53 Hot Keys: Function keys give you access to a group of commands throughout the BIOS utilit y . Function Command Description F1 Help Gives the list of options available for each item. Shift F2 Color Change the color of the display window.
BIOS Setup Utility SY-6BA+ IV 54 3-1 SOYO COMBO SETUP This Motherboard does not use any hardware jumpers to set the CPU frequenc y . Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP].
BIOS Setup Utility SY-6BA+ IV 55 3-1.1 Quick CPU Frequency Setup Quick CPU Frequency Setup Setting Description Note CPU Name & CPU ID The BIOS will read the CPU name string and CPU ID code From the CPU and it will display it here. This item provides information only and can not be change.
BIOS Setup Utility SY-6BA+ IV 56 Quick CPU Frequency Setup (Continued) Quick CPU Frequency Setup Setting Description Note If [CPU Frequency] field is set to [Manual] CPU Ratio After you have selected the host clock, choose the right multiplier for the CPU.
BIOS Setup Utility SY-6BA+ IV 57 3-1.2 System Boot Control Settings System Boot Control Settings Setting Description Note A, C, SCSI C, A, SCSI C, CD-ROM, A CD-ROM, C, A D, A, SCSI E, A, SCSI F, A, SC.
BIOS Setup Utility SY-6BA+ IV 58 3-1.5 C.I.H. 4-W AY Protection Setting Setting Description Note Disabled C.I.H. 4- WA Y Protection Enabled When set to enabled, the BIOS can only be programmed through AWDFLASH, making sure that any virus is unable to program the system BIOS.
BIOS Setup Utility SY-6BA+ IV 59 Power Management (Continued) PM Events Setting Description Note Disabled Default Power-On by Ring/LAN Enabled The system will self-power on me when the modem is ringing. Disabled The system ignores the alarm. Default Resume by Alarm Enabled Set alarm to power on the system by the date (1-31) or time ( hh :mm:ss).
BIOS Setup Utility SY-6BA+ IV 60 CPU Device Monitoring (Continued) CPU Device Monitoring Setting Description Note Current System T emp. ° C/ ° F Show the current status of the system temperature. Current CPU T emperature ° C/ ° F Show the current status of CPU temperature.
BIOS Setup Utility SY-6BA+ IV 61 3-2 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] ke y . This screen allows you to modify the basic CMOS settings. After you have completed the changes, press [Esc] key to return to the Main Menu.
BIOS Setup Utility SY-6BA+ IV 62 3-2.2 Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary (Secondary) Master & Slave Setting Description Note Auto BIOS detects hard disk type automaticall y .
BIOS Setup Utility SY-6BA+ IV 63 3-2.4 Video Select the video mode: EGA/VGA (Default), CGA 40, CGA 80, Mono (Monochrome). 3-2.5 Halt On When the BIOS detects system errors, this function will stop the system.
BIOS Setup Utility SY-6BA+ IV 64 3-3 BIOS FE ATURES SETUP Select the [BIOS FE A TURES SETUP] option from the Main Menu and press [Enter] ke y . ROM PCI/ISA BIOS BIOS FE A TURES SETUP AWARD SOFTWARE, INC. Anti - Virus Protection : Disabled Assign IRQ For VGA : Enabled CPU Internal Cache : Enabled HDD S.
BIOS Setup Utility SY-6BA+ IV 65 3-3.1 Virus Warning Setting Description Note Disabled Default Anti - Virus Protection Enabled If set to enabled, the Paragon Anti-Virus. Function will scan your boot drive for boot virusses. If a boot virus is detected, the BIOS will display a warning message.
BIOS Setup Utility SY-6BA+ IV 66 3-3.4 Other Control Options Other Control Options Setting Description Note On Puts numeric keypad in NumLock mode at boot-up. Default Boot Up NumLock Status Off Puts numeric keypad in arrow key mode at boot-up. 3-3.5 Security Option Use this feature to prevent unauthorized system boot-up or use of BIOS Setup.
BIOS Setup Utility SY-6BA+ IV 67 3-3.7 Typematic Settings Typematic Settings Setting Description Note Disabled Default Typematic Rate Setting Enabled Enables to adjust the keystroke repeat rate.
BIOS Setup Utility SY-6BA+ IV 68 Other Control Options Other Control Options Setting Description Note Disabled Enabled Video or Adapter BIOS Shadow The BIOS is shadowed in a 16K segment if it is enabled and if it has BIOS present. These 16 segments can be shadowed from ROM to RAM.
BIOS Setup Utility SY-6BA+ IV 69 3-4 CHIPSET FEATURES SETUP Caution: Change these settings only if you are already familiar with the Chipset. The [CHIPSET FE A TURES SETUP] option changes the values of the chipset registers. These registers control the system options in the computer.
BIOS Setup Utility SY-6BA+ IV 70 CHIPSET FEATURES SETUP CHIPSET FEATURES Setting Description Note Disabled Auto Configuration Enabled It is strongly recommended to enable this option so that the system automatically sets all chipset feature options on the left panel of the screen (except for cache update & BIOS cacheable).
BIOS Setup Utility SY-6BA+ IV 71 CHIPSET FEATURES SETUP (Continued) CHIPSET FEATURES Setting Description Note 16 BIT I/O Recovery Time 1 Use the default setting Default Disabled Default Memory Hole At 15M-16M Enabled Some interface cards will map their ROM address to this area.
BIOS Setup Utility SY-6BA+ IV 72 3-5 POWER MANAGEMENT SETUP The [POWER MANAGEMENT SETUP] sets the system's power saving functions. ROM PCI/ISA BIOS POWER MANAGEMENT SETUP AWARD SOFTWARE, INC.
BIOS Setup Utility SY-6BA+ IV 73 3-5.1 Power Management Controls Power Management Controls Setting Description Note Disabled Default ACPI function Enabled ACPI (Advanced Configuration Power Management Interface) Yes To use Advanced Power Management (APM) you must run [power.
BIOS Setup Utility SY-6BA+ IV 74 3-5.2 PM Timers PM Timers Setting Description Note User Define Lets you define the HDD and system power down times. Default Disable Disables the Green PC Features.
BIOS Setup Utility SY-6BA+ IV 75 3-5.3 PM Events PM Events Setting Description Note Disabled VGA Active Monitor Enabled Enables the power management timers when a [no activity] event is detected. Default Disabled Default IRQ 8 Break Suspend Enabled Alarm function is active.
BIOS Setup Utility SY-6BA+ IV 76 3-6 PNP/PCI CONFIGURATION SETUP This option sets the Motherboard's PCI Slots. ROM PCI/ISA BIOS PNP/PCI CONFIGURATION AWARD SOFTWARE, INC.
BIOS Setup Utility SY-6BA+ IV 77 3-6.1 PNP/PCI Configuration Controls PNP/PCI Controls Setting Description Note Manual BIOS does not manage PCI/ISA PnP card IRQ assignment.
BIOS Setup Utility SY-6BA+ IV 78 PNP/PCI Configuration Setup (Continued) PNP/PCI Setup Setting Description Note How to set the BIOS to release the IRQ to the PnP Interrupt pool: Interrupt Line PnP / P.
BIOS Setup Utility SY-6BA+ IV 79 3-7 LOAD SETUP DE FAULTS Select the [LOAD SETUP DEFAU LTS] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.
BIOS Setup Utility SY-6BA+ IV 80 3-8 INTEGRATED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGR A TED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer.
BIOS Setup Utility SY-6BA+ IV 81 3-8.1 IDE Device Controls IDE Controls Setting Description Note Disabled IDE HDD Block Mode Enabled Invokes multi-sector transfer instead of one sector per transfer.
BIOS Setup Utility SY-6BA+ IV 82 3-8.3 FDC Controls FDC Controls Setting Description Note Disabled Turn off the on-board floppy controller Onboard FDC controller Enabled Use the on-board floppy controller Default 3-8.
BIOS Setup Utility SY-6BA+ IV 83 3-8.5 Onboard Parallel Ports Onboard Parallel Ports Setting Description Note 378H/IRQ7 Default 3BCH/IRQ7 Onboard Parallel Port 278H/IRQ5 Choose the printer I/O address. ECP/EPP Default SPP ECP Parallel Port Mode EPP/SPP The mode depends on your external device that connects to this port.
BIOS Setup Utility SY-6BA+ IV 84 3-8.6 MULTI I/O ADDRESSES Default settings for multi-I/O addresses are as follows: Port I/O Address IRQ Status LPT1 378H 7 ECP/EPP COM1 3F8H 4 COM2 2F8H 3 Warning: If a default I/O address conflicts with other I/O cards such as sound card, you must change one of the I/O addresses to remedy to this address conflict.
BIOS Setup Utility SY-6BA+ IV 85 3-9 SUPERVISOR PASSWORD Based on the setting you have made in the [Security Option] of the [BIOS FE A TURES SETUP] section, the password prevents access to the system or the setup program by unauthorized users. Follow this procedure to set a new password or disable the password: 1.
BIOS Setup Utility SY-6BA+ IV 86 3. Enter your new password and press [Enter]. The following message appears, prompting to confirm the new password: 4.
BIOS Setup Utility SY-6BA+ IV 87 3-11 IDE HDD AUTO DETECTION This Main Menu function automatically detects the hard disk type and configures the STANDARD CMOS SETUP accordingl y .
Drivers installation SY-6BA+ IV 88 Chapter 4 DRIVERS INSTALLATION Your SY-6BA+ IV Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains the user's manual file for your.
Drivers installation SY-6BA+ IV 89 Step 2. Read SOYO [6BA+ IV] Manual Click the Read Manual button to open the user's manual file of your Motherboard. Please note that if the Start Up program was unable to determine which SOYO Motherboard you own, the manual selection menu will pop up, as shown belo w .
Drivers installation SY-6BA+ IV 90 Step 3. Install Drivers Click the Install Drivers button to display the list of drivers software that can be installed with your Motherboard. The Start Up program displays the drivers available for the particular model of Motherboard you own.
Drivers installation SY-6BA+ IV 91 The following drivers are available for Windows 98 (Driver Installation Menu) A short description of all available drivers follows: Ø Intel .
Drivers installation SY-6BA+ IV 92 Your motherboard comes with a hardware monitoring IC. By installing this utility Temperature, Fan speed and V oltages can be monitored. It is also possible to set alarms when current system values exceed or fall below pre-set values.
Drivers installation SY-6BA+ IV 93 button. Please make sure to install only the drivers adapted to your system, or otherwise this cause system malfunctions.
The ATA 66 Driver installation SY-6BA+ IV 94 Chapter 5 THE ATA 66 DRIVER INSTALL ATION Ø Installing the Windows 95/98 Drivers Usuall y , when you boot up the Windows 95/98 system for the first time, the system will be able to detect the HPT366 Ultra DMA host Adapter automatically and ask you to install the driver for HPT366.
The ATA 66 Driver installation SY-6BA+ IV 95 13. Click on the "Finish" button. 14. Then the system will ask you to restart the system. If the settings reported in step 12 are not what set on the host adapter, you must adjust the settings by using the device manager in the System control panel before restarting your computer.
The ATA 66 Driver installation SY-6BA+ IV 96 Your Hard Disk to know how to partition and format a hard disk drive. 2. Checking the Installation If you want to check if the HPT366 host adapter and its device driver are correctly installed, you can: (1.
The ATA 66 Driver installation SY-6BA+ IV 97 instructions on the display screen to continue booting with the last known good configuration: Press spacebar NOW to invoke the Last Known Good menu 3. Once your computer is operational again, check all of the hardware and software configuration changes you want to make.
The ATA 66 Driver installation SY-6BA+ IV 98 NOTE: Before you send an e-mail, please visit our Web Site (http://ww w .highpoint-tech.com) to check if there is a new or updated HPT366 device driver for your operating system.
The ATA 66 Driver installation SY-6BA+ IV 99.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il SOYO SY-6BA+ IV è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del SOYO SY-6BA+ IV - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso SOYO SY-6BA+ IV imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul SOYO SY-6BA+ IV ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il SOYO SY-6BA+ IV, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del SOYO SY-6BA+ IV.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il SOYO SY-6BA+ IV. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo SOYO SY-6BA+ IV insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
