
Sony Electronics Inc. 16450 West Bernardo Drive San Diego, CA 92127 www.sony.com/plasma
®



PART#: SPMTRI/C MATERIALS USED: 12 (GA) CRS, Clear acrylic base COLOR: Silver A. Back plate B. Stand support C. Clear base D. Security access screws E. (1) Cable access hole F. Fixed tabletop mounting holes
Dimensions are in Inch and mm
20.50 (520.7)
20.00 (508)
12 X 22 (304 x 558) 1.00 (25.4)
(A)
MODEL A PFM-32C1 .37 (9.4) FWD32LX1,FWD32DV1 1.0 (25.4) PFM-42B1,PFM-42V1, FWD42X1 .72 (18.2) PFM-42LX1, FWD42DV1 1.0 (25.4) PFM-50C1 .90 (22.8) PFM-50DV1 1.0 (25.4)


Phillips screwdriver (4) M5 x 10 (mm) flat head Phillip screws (4) Clear rubber feet
(6) M5 x 30 (mm) flat head Phillip screws (2) M6 x 30 Phillips head screws (used on the 30” plasma only) (2) M5 x 12 (mm) phillip security screws (used on 42" and 50" plasma displays only) (2) #10 x 1-3/4" wood screws (Optional use)

Step 1 Unpack the components from the box and set them on the floor. Invert and apply the four (4) clear rubber feet to the flat surface on the base, locate the four mounting points on the clear base. Secure the two (2) upright supports (flat surface facing out) to the base by using the four (6) M5 x 30 (mm) Phillip screws (supplied). CAUTION: Do not over tighten the screws.
(6) M5 x 30 Flat head screws
Step 2 The stand fits a 32" 42" and 50" PFM series (Sony plasma displays only). The plate is stamped with two plasma sizes. Check the size that fits your plasma before installing. NOTE: If using a 32” plasma, the plate is not needed. Mount the plasma quick release sleeves from the plasma to the key-holes on the uprights. The size and arrow must always point up prior to installation, finger tighten the (4) M5 x 10 (mm) phillips flat head screws then tighten the screws. See figure 2.
(4) M5 x 10 Flat head screws


Step 3 Raise the display with the securing sleeves installed to the plasma. Slip the sleeves through the four (4) keyholes on the back plate and drop it down slowly, make sure all of the four (4) sleeves are in the keyhole slot before letting go of the plasma. On the 42" and 50" two (2) M5 x 12 Phillip screws (security screws) can be used for additional security. See figure 3. NOTE: If using a 32” plasma, secure it with the two (2) M6 x 30 Phillip screws supplied.
M5 x 12 phillips
M6 x 30 phillips
screws · screws


Step 1 Invert the stand and locate the two (2) mounting points on the bottom of the stand for (optional) fixed tabletop installation. Measure the distance between center to center of these two (2) holes and mark the table. See figure 4.

Step 2 OPTIONAL TABLE MOUNTING If securing to a wood table, mark the table and drill properly. Secure the stand with the two (2) #10 x 1-1/4" wood screws (supplied). NOTE: Longer or shorter wood screws and or mounting hardware depending on your installation environment are (commercially available). See figure 5.
I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.