Manuale d’uso / di manutenzione del prodotto ALF-F del fabbricante Bakers Pride Oven
Vai alla pagina of 60
Automatic Lift Fryer MODELS ALF-F, & ALF-FC Service Manual Serial Numbers 137733 and higher.
Warranty Information LIMITED ONE YEAR WARRANTY BKI (The "Company") warrants to the original purchaser that at time of shipment from the Com pany factory, this equipment will be fre e from defect in materials and workmanship.
Automatic Lift Fryer Table of Contents 1 T able of Content s Table of Contents .............................................................................................................. .......................... 1 Introduc tion ..................
Automatic Lift Fryer Introduction 2 Introduction The ALF Fryer is compact, attractive and functional in desi gn. It is constructed of a stainless steel fryer pot for cleaning ease.
Automatic Lift Fryer Introduction 3 Specific Precautions Risk of fire exists if the oil level dr ops below 5mm of the maximum oil level. Use of oil/shortening older than the manu facture rs recommendation s for life of the oil is prone to surge boiling and flas h fires.
Automatic Lift Fryer Introduction 4 Safe Work Practices Noncombustible Floors Only Make sure your floor is non comb ustible. Do not operate your fryer on floors that are wood, car peted or have rubber mats. • Placing your fryer on a combustible floor could cause a fire.
Automatic Lift Fryer Introduction 5 Do Not Overfill The Fryer With Shortening Hot shortening and steam may esc ape and bu rn you if you put too much shortening in the fryer. Fill the fryer to approximately one inch below the fill marks that are in side the fryer pot.
Automatic Lift Fryer Introduction 6 Keep this manual with the Equipment This manual is an important part of your equipment. Always keep it near for easy access. If you need to replace this manual, contact: BKI Technical Services Depart ment P.O. Box 80400 Simpsonville, S.
Automatic Lift Fryer Introduction 7 Be Prepared for Emergencies Be prepared for fires, injuries, or oth er emergencies. Keep a first aid kit and a fire extinguisher near the equipment. You must use a 40-pound Type BC fire extinguishe r and keep it within 25 feet of your equipment.
Automatic Lift Fryer Introduction 8 Safety Labels.
Automatic Lift Fryer Installation 9 Inst allation Serious injury, equipment damage or death coul d result if attempting to install this fryer yourself. Ensure that an authoriz ed BKI service agent installs the fryer. Unpacking and Handling It is the owners’ responsibility to file all freight clai ms with the delivering truck lin e.
Automatic Lift Fryer Installation 10 Initial Test and Adjustment 1. Fill pot with shortening to about one inch below the m ark. Risk of fire exists if the oil level drops below the minimum oil level. The level of oil within the pot must not fall below 5mm of the maximum oil level.
Automatic Lift Fryer Operation 11 Operation Controls and Indicators Refer to the figure and table below for a n expl anatio n of the fryer’s controls and indicators.
Automatic Lift Fryer Operation 12 Item # Description Function 1 Computer Used to set and activate product programs. 2 Momentary Basket Switch UP – Momentarily pushing the switch to this position causes the lift mechanism to rise. This is enabled only when the FILTER/OFF/FRY switch is in the FRY position.
Automatic Lift Fryer Operation 13 Item # Description Function ALARM button This button allows the user to set an elapsed time at which the internal alarm will sound during a cycle. The time is set by pressing and holding the ALARM button while using the UP and DOWN arrows to change the time.
Automatic Lift Fryer Operation 14 Care of the Shortening To extend the life of your shortening, for the best possible flavor in your products, and for economy and efficiency of operation, we urge you to follow the se re commen dations: 1.
Automatic Lift Fryer Operation 15 3. The digital timer has a STIR OIL function that operates in on e of four reconfigu rable modes. If the timer needs to be reconfigured, follo w step a. If the timer does not need to be reconfigured, follow step b. a.
Automatic Lift Fryer Operation 16 Cooking 1. Ensure that the Start-Up procedures have been pe rformed. 2. When frying chicken, lower the basket into t he shorteni ng by depressing the b asket switch to the DOWN position. Hot shortening may splash out of the pot cau sing severe injury when drop ping chicken into pot.
Automatic Lift Fryer Operation 17 ALF-FC Operation System Progra mmi ng Use the following figure and table to set opt ions that apply to each produ ct programs.
Automatic Lift Fryer Operation 18 Table 1. System Program m ing Procedure STEP ACTION DISPLAY COMMENTS 1 Press the FILTER/OFF/FRY switch to FRY . LOW 2 Press PROG on the keypad. PROGRAM CODE 3 Input 1712 and ENTER. PROGRAM SYSTEM 4 Press ENTER. PROGRAM DEGREES ° F This command allows you to choose the temperature scale option you want to use.
Automatic Lift Fryer Operation 19 Product Programming Use the following figure and table to set a maximum of eight produ ct programs. The product program s must be set before cooking can begin.
Automatic Lift Fryer Operation 20 Table 2. Product Programm ing Procedure STEP ACTION DISPLAY COMMENTS 1 Press the FILTER/OFF/FRY switch to FRY . LOW 2 Press PROG on the keypad. PROGRAM CODE 3 Input 1724 and press E NT E R. PROGRAM PRODUCT # 4 Select the program product number (1-8).
Automatic Lift Fryer Operation 21 STEP ACTION DISPLAY COMMENTS 12 Press TOGGLE/CLEAR until the desired option is displayed. PROGRAM VALVE1 X X refers to the solenoid valve option selected. OPEN is used for Models ALF and BLF Automa tic Lift fryers. If your program requires the solenoid valve to be closed while cooking, choose the CLOSED option.
Automatic Lift Fryer Operation 22 Start-Up 1. Make sure the main drain valve is clo sed. 2. Fill pot with shortening to about one inch below the m ark. Risk of fire exists if the oil level drops below the minimum oil level. The level of oil within the pot must not fall below 5mm of the maximum oil level.
Automatic Lift Fryer Operation 23 4. Carefully drop the chicken in the shortening one piece at a time starting with thi ghs a nd drumsticks. The fryer is designed to accommodate 32 piece s of chicken. 5. Press the desired program numbe r a second time .
Automatic Lift Fryer Maintenance 24 Maintenance Failure to comply with the maintenance below could result in a serious a ccident. Your fryer will need periodi c mainten ance and servicing. We stron gly suggest that you use only a service company that is authorize d by BKI to do this work.
Automatic Lift Fryer Maintenance 25 Filtering Procedure Breaded foods require frequent filtering. An excess a m ount of breading left in the fryer pot will redu ce the life of the shortening. We recommend the sho rtenin g be filtered after every three frying cycle loads.
Automatic Lift Fryer Maintenance 26 To refill the pot through the rin se hose, use the steps below: • Make certain that the rinse hose is connected to rinse hose conne ctor. • Holding the hose by the handle, place hose n ozzle inside the pot. • Position the FILL lever in the THRU HOSE position.
Automatic Lift Fryer Maintenance 27 10. Before draining the cleaning solution , remove the filter bag, screen and pipe conne ctions from the filter vat. This must be done before draining the cleanin g soluti on. NEVER pump water or detergent through t he filter system.
Automatic Lift Fryer Maintenance 28 Filter Pad Replacement The filter pad must be replaced daily. If the shortening has a milky color when it is pumped into the pot, the filter pad should be replaced immediately. If the filter pad is not properly closed, breading crumbs will get through the pad opening and clog the pump.
Automatic Lift Fryer 29 Troubleshooting Refer to the table below for troubl eshoot ing information. Problem Cause Possible Solution Shortening Heating Too Slowly Low voltage or improper voltage Contact an authorized BKI service agent for corrective action.
Automatic Lift Fryer Replacement Parts 30 Replacement Part s Use the information in this section to identify repl acement parts. To order repla ceme nt part s, call your local BKI sales and service representat ive. Before calli ng, please note the serial number, model numbe r and voltage on the rating tag affixed to the unit.
Automatic Lift Fryer Replacement Parts 31 Figure 3. Drain Valve & Plugs (SB1999S) Table 3. Drain Valve & Plugs (SB1999S) Parts ITEM # PART # QTY DESCRIPTION 1 MB19101000 1 DRAIN VALVE REPLACEM.
Automatic Lift Fryer Replacement Parts 32 Figure 4. Door Assembly (SB1289) Table 4. Door Assembly (SB1289) Parts ITEM # PART # QTY DESCRIPTION 1 F0083 2 THR EAD I NSER T 10- 24 STEEL 2 H0010 1 HINGE, .
Automatic Lift Fryer Replacement Parts 33 Figure 5. Drain/Motor/Piping Assembly.
Automatic Lift Fryer Replacement Parts 34 Table 5. Drain/Motor/Piping Assembly Parts ITEM # PART # QTY DESCRIPTION 1 D0060 1 VALVE, DRAIN SS BALL&PLT.
Automatic Lift Fryer Replacement Parts 35 Figure 6. Control Panel ALF-F.
Automatic Lift Fryer Replacement Parts 36 Table 6. Control Panel ALF-F Parts ITEM # PART # QTY DESCRIPTION 1 K0040 1 KNOB, S/S STRAT T0075 2 T0075 1 THERMOSTAT, SOLID STATE FRYER 3 PL0004 1 PILOT LIGH.
Automatic Lift Fryer Replacement Parts 37 Figure 7. Control Panel ALF-FC.
Automatic Lift Fryer Replacement Parts 38 Table 7. Control Panel ALF-FC Parts ITEM # PART # QTY DESCRIPTION 1 CP0039 1 CONTROLLER, VFD LESS HARNESS 2 R0134 R0134 4 3 RELAY, MERCURY MDI 60NO220A (A N15.
Automatic Lift Fryer Replacement Parts 39 Figure 8. Oil Vat Assembly (AN86202800).
Automatic Lift Fryer Replacement Parts 40 Table 8. Oil Vat Assembly (AN86202800) Part s ITEM # PART # QTY DESCRIPTION 1 SB1991 1 QUIK DISCONNECT BRACKET WELD MENT 2 O0013 1 O-RING, FLUOROCA RBON V680-.
Automatic Lift Fryer Replacement Parts 41 Figure 9. Quick Disconne ct Assemb ly Table 9. Quick Disconn ect Assembl y Parts ITEM # PART # QTY DESCRIPTION AB86200700 1 B0996 1 BALL, 11/16" STEEL BE.
Automatic Lift Fryer Replacement Parts 42 Figure 10. Components 1 2 3 4 5 6 7 8 9 10 11 12.
Automatic Lift Fryer Replacement Parts 43 Accessories Description Accessory # Figure # Item # BASKET, ALF USES LIFT HANDLE - option B0115B Figure 11 1 HANDLE, TEE STYLE LIFT H0151 Figure 11 2 BRUSH, D.
Automatic Lift Fryer Replacement Parts 44 Figure 12. Storage Cover Assem bly (Optional) Table 10. Storage Cover Assem bly Part s ITEM # PART # QTY DESCRIPTION 1 ALFA123 1 HANGER, FRY POT COVER 2 SCR13.
Automatic Lift Fryer Wiring Diagrams 45 Wiring Diagrams Refer to the table below to find the wirin g diagram a s sociated with your unit. Wiring Diagram Diagram # Figure # Page # ALF-F 208V/240V, 3 Ph.
Automatic Lift Fryer Wiring Diagrams 46 Figure 13. ALF-F 208V 3 Phase or ALF-F 240V 3 Phase M.
Automatic Lift Fryer Wiring Diagrams 47 Figure 14. ALF-F 208V/240V, 1/3 Phase M.
Automatic Lift Fryer Wiring Diagrams 48 Figure 15. ALF-FC 208V 1/3 Phase or ALF-F C 240V 1/3 Phase (Sheet 1 of 3).
Automatic Lift Fryer Wiring Diagrams 49 Figure 15. ALF-FC 208V 1/3 Phase or ALF-F C 240V 1/3 Phase (Sheet 2 of 3).
Automatic Lift Fryer Wiring Diagrams 50 Figure 15. ALF-FC 208V 1/3 Phase or ALF-F C 240V 1/3 Phase (Sheet 3 of 3).
Automatic Lift Fryer Wiring Diagrams 51 Figure 16. ALF-FC 208V/240V/3 Phase (sh eet 1 of 3).
Automatic Lift Fryer Wiring Diagrams 52 Figure 16. ALF-FC 208V/240V/3 Phase (sh eet 2 of 3).
Automatic Lift Fryer Wiring Diagrams 53 Figure 16. ALF-FC 208V/240V/3 Phase (sh eet 3 of 3).
Automatic Lift Fryer Notes 54 Notes.
Automatic Lift Fryer 55.
Automatic Lift Fryer 56.
Automatic Lift Fryer 57.
P.O. Box 80400, Simpsonvill e, S.C. 29680-0400, USA http://www.bkideas.co m Made and printed in t he U.S.A LI0228/0808.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Bakers Pride Oven ALF-F è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Bakers Pride Oven ALF-F - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Bakers Pride Oven ALF-F imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Bakers Pride Oven ALF-F ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Bakers Pride Oven ALF-F, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Bakers Pride Oven ALF-F.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Bakers Pride Oven ALF-F. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Bakers Pride Oven ALF-F insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
