Manuale d’uso / di manutenzione del prodotto PCV-RX462DS del fabbricante Sony
Vai alla pagina of 134
.
ii Notice to Users © 2001 Sony Electronics Inc. Reproduction in whole or in part without written permission is prohibited. All rights r eserved. This manual and the software described her ein, in whole or in part, may not be reproduced, translated, or reduced to any machine-readable form without prior written approval.
iii Safety Information and Caution ❑ T o prevent fire or shock hazar d, do not expose your desktop to rain or moisture.T o avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only . ❑ Never install modem or telephone wiring during a lightning storm.
iv ❑ Pour prévenir tout risque d’incendie ou d’électrocution, gar der cet appareil à l’abri de la pluie et de l’humidité. ❑ Pour prévenir tout risque d’électrocution, ne pas ouvrir le châssis de cet appareil et ne confier son entretien qu’à une personne qualifiée.
v Fo r que st ion s reg ardi ng y our p rod uct o r for the Sony Service Center nearest you, call 1-888-476-6972 in the United States or 1-800-961-7669 in Canada. Sony Customer Support can be reached at http://www .sony .com/pcsupport. Regulatory Information Model No.
vi interference to radio or television r eception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: : ❑ Reorient or relocate the receiving antenna.
vii If trouble is experienced with this modem, f o rr e p a i ro rw a r r a n t yi n f o r m a t i o n ,p l e a s e contact 1-888-4SONY -PC, or write to the Sony Customer Information Center , 12451 G a t e w a yB l v d . ,F o r tM y e r s ,F L3 3 9 1 3 .
viii For the Sony Service Center nearest you, call 1-888-476-6972 in the United States or 1-800-961-7669 in Canada. ! Do not handle damaged or leaking lithium batteries . ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer .
ix Industry Canada Notice NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requir ements as prescribed in the appropriate T erminal Equipment T echnical Requirements document(s).
x lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rural es.
xi Contents Notice to Users .................................................................................... ii Owner’s Record ................................................................................... ii Safety Information and Caution .
V AIO Digital Studio™ System Reference Manual xii Chapter 3 — Removing, Installing, and Replacing Components ....................................................................... 27 Removing the Side Cover .......................................
xiii CLR CMOS Jumper ........................................................................... 76 Chapter 5 — Fax/Modem Card .......................................... 77 HomePNA Modem ..............................................................
V AIO Digital Studio™ System Reference Manual xiv Audio ....................................................................................................... 111 Communications ......................................................................
1 Chapter 1 Identifying Components The following sections identify and describe each component that is visible from the exterior of the V AIO Digital Studio™ computer .
V AIO Digital Studio™ System Reference Manual 2 Front V iew All Models.
Identifying Components 3 Drives PCV -RX462DS/PCV -RX463DS/PCV -RX465DS/PCV -RX470DS/PCV -RX480DS Drive Description Floppy disk drive 3.5-inch, 1.44 MB.
V AIO Digital Studio™ System Reference Manual 4 PCV -RX490TV *** Data on a CD-R/CD-RW is written at a constant transfer rate of 2X, 4X, 8X (max. for CD-RW), or 12X, depending on the speed you select. ††† Data on a CD-R/CD-ROM is read at a variable transfer rate, ranging from 13X at the innermost track to 32X at the outermost track.
Identifying Components 5 † Data on a DVD-ROM is read at a variable transfer rate, ranging from 2X at the innermost track to 4X at the outermost track. The average data transfer rate is 3.3X (4455 KBps). ‡ Data on a DVD-RW/DVD-R is read at a constant transfer rate of 2X.
V AIO Digital Studio™ System Reference Manual 6 Buttons and Switches All Models Button or switch Description Power/Stand by switch T urns system power on, off, or into Stand by mode. Floppy disk eject button Ejects a floppy disk. Optical disc eject button Automatically opens and closes the optical drive tray .
Identifying Components 7 Indicators All Models Indicator Description Power/Stand by indicator Stand by (red) indicates the computer is in Stand by mode. On (blue) indicates the computer is out of Stand by mode, ready to use. Off (no color) indicates the computer is turned off, or in hibernation mode.
V AIO Digital Studio™ System Reference Manual 8 Connectors PCV -RX462DS/PCV -RX463DS/PCV -RX465DS/PCV-RX470DS/PCV -RX480DS Connector Description i.LINK® (IEEE1394) * * To connect to a 6-pin i.LINK device, use the i.LINK header on the back of the system.
Identifying Components 9 PCV -RX490TV Connector Description Universal Serial Bus (USB) ports (2) Connects to USB devices. i.LINK (4-pin) port (IEEE1394) Connects to a digital device that has a 4-pin i.LINK connector . S - V i d e oI np o r t C o n n e c t st oa nS - v i d e oc a b l e( o p t i o n a l ) .
V AIO Digital Studio™ System Reference Manual 10 Rear Vi ew All Models Mouse Keyboard USB1, USB2 Ethernet Serial Printer /Parallel Headphones Line In Microphone Monitor Line Power DVI Telephone** i.
Identifying Components 11 Icons All Models All Models Icon Description Mouse port Keyboard port Universal Serial Bus (USB) port Ethernet port (for LAN connection only) Serial port Printer port i.
V AIO Digital Studio™ System Reference Manual 12 Headphones LINE IN jack (audio) Microphone jack Monitor port Line jack (for telephone line from primary service jack) T elephone jack (for phone) * DVI (LCD) Monitor port * In models with an HPNA modem, the telephone jack does not exist.
Identifying Components 13 I/O Connectors The following section identifies the various I/O connectors. Keyboard and Mouse Ports The keyboard and mouse ports ar e physically identical and have the same pinout. They are standar d 6-pin PS/2®-type female ports.
V AIO Digital Studio™ System Reference Manual 14 Serial Port The serial port is a standard 9-pin DB-9 male port. Printer/Parallel Port The printer/parallel port is a standard 25-pin DB-25 female port. Monitor Port The monitor port is a standard 15-pin female high-density VGA-type port located on the AGP plug-in card.
Identifying Components 15 DVI Port The DVI port is a 24-pin DVI port that can be attached to a Sony XGA LCD panel (PCV A-15XD2), which uses a DVI connector cable (sold separately). The DVI port is located on the AGP plug-in card. Y ou can physically connect both a VGA and an LCD monitor at the same time.
V AIO Digital Studio™ System Reference Manual 16 Mic, Line In, and Headphones Jacks The mic, line in, and headphones jacks are physically identical, but have differ ent connections. They are standar d 3.5 mm stereo mini-jacks. T elephone and Line Jacks The telephone and line jacks are physically identical and have identical connections.
Identifying Components 17 i.LINK® (IEEE1394) Ports The 6-pin i.LINK port on the back of the system can supply power from the computer to a device if the device also has a 6-pin i.LINK port. The 6-pin port supplies 10 V to 12 V and a maximum power of 6 watts.
V AIO Digital Studio™ System Reference Manual 18 Expansion Slots T h e r ea r et h r e eP C Is l o t s ,t w oo fw h i c ha r ea v a i l a b l ef o re x p a n s i o n( s l o t No. 2 and slot No. 3), in the PCV -RX462DS/PCV -RX463DS/ PCV -RX465DS/PCV -RX470DS/PCV -RX480DS models.
Identifying Components 19 Remote Control PCV -RX490TV The features of the Giga Pocket Personal V ideo Recorder system can be controlled using the r emote contr ol (supplied). The remote contr ol can start and stop video recor ding and playback, select channels, and set viewing prefer ences.
V AIO Digital Studio™ System Reference Manual 20.
21 Chapter 2 Configuring Y our System This chapter contains information on configuring your system. Configuring your system can consist of the following: ❑ Making changes to the BIOS settings. ❑ Making changes to the display's power management settings.
V AIO Digital Studio™ System Reference Manual 22 Accessing the BIOS Setup Utility Y ou must access the BIOS Setup Utility to make changes to the BIOS settings (see “CMOS Setup Options” on page 85 for information on BIOS settings). 1 Reboot your computer by selecting Shut Do wn.
Configuring Your System 23 Changing the Display's Power Management Settings A display that has power management capability is designed to operate on reduced power or shut itself of f after the system has been idle for a specified period of time. 1 From the Start menu, point to Settings, click Contr ol Panel, then click Display .
V AIO Digital Studio™ System Reference Manual 24 The T urn off monitor option allows you to specify the period of inactivity (in minutes) that you want to elapse before your monitor turns off when your computer is running on AC power . The display reactivates when you move the mouse or pr ess a key .
Configuring Your System 25 5 Select the desired settings. 6 Click the Hibernate tab. 7 Select the desired settings, and then click OK..
V AIO Digital Studio™ System Reference Manual 26.
27 Chapter 3 Removing, Installing, and Replacing Components This chapter describes removing, installing, and r eplacing major components for upgrading, reconfiguring, and troubleshooting the components.
V AIO Digital Studio™ System Reference Manual 28 Removing the Side Cover Y ou must remove the side cover to access the system board, add-in car ds, power supply , battery , memory , and internal drives. 1 From the r ear of the unit, pull the metal tab shown in the next diagram.
Removing, Installing, and Replacing Components 29 Replacing the Side Cover 1 From the r ear of the unit, align the bottom of the cover so that it slips into the lip on the bottom of the unit. 2 Push the top of the cover up against the top of the unit until the cover snaps into position.
V AIO Digital Studio™ System Reference Manual 30 Installing a PCI Add-In Card 1 Remove the side cover (see “Removing the Side Cover” on page 28). 2 Locate an available expansion slot. 3 Remove the slot cover adjacent to the selected slot (see “Removing a Slot Cover” on page 43).
Removing, Installing, and Replacing Components 31 6 Attach any necessary cables to the card (see the instructions that came with the add-in card). 7 Replace the side cover (see “ R e p l a c i n gt h eS i d eC o v e r ” on page 29). 8 T urn on the computer and follow any instructions that came with the add-in card.
V AIO Digital Studio™ System Reference Manual 32 Removing a PCI Add-in Card 1 Remove the side cover (see “Removing the Side Cover” on page 28). 2 Disconnect any cables attached to the add-in card you want to rem ov e. 3 Remove the screw that secur es the add-in car d to the chassis.
Removing, Installing, and Replacing Components 33 5 If y ou d o no t re pl ac e th e ca rd or i ns ta ll a no th e r ad d- in c ard , in s ta ll a slot cover over the vacant slot at the rear of the chassis (see “Covering an Open I/O Slot” on page 44).
V AIO Digital Studio™ System Reference Manual 34 Replacing the Lithium Battery Y ou may need to replace the lithium battery if your computer consistently loses the date or time settings after turning it off. The lithium battery has a typical life of three years, after which the battery may b e too weak to power the CMOS memory .
Removing, Installing, and Replacing Components 35 8 If necessary , remove any add-in cards (see “Removing a PCI Add-in Card” o np a g e3 2 )t og a i na c c e s st ot h eb a t t e r y .
V AIO Digital Studio™ System Reference Manual 36 16 If the error message “Err or: Check date and time settings.” appears during the reboot sequence, pr ess F2 during the r eboot process to access the BIOS Setup Utility .
Removing, Installing, and Replacing Components 37 Installing System Memory 1 Choose the size of the memory module and configuration as shown in the following table. Memory modules can vary in size and speed between sockets. The minimum memory size is 8 MB.
V AIO Digital Studio™ System Reference Manual 38 8 Remove the AGP add-in card. 9 Align the module over the appropriate socket, noting the location of p i n1o nt h em o d u l ea n dp i n1o nt h es o c k e t . ✍ Grasp the card with one hand on each end, and gently pull up as you rock the card from side to side .
Removing, Installing, and Replacing Components 39 10 Carefully but firmly insert the edge of the module into the socket. 11 Press down firmly and evenly at both corners until the module is fully seated. ✍ When the module is fully seated, the handles on each side are straight up and lock ed into the slot on each side of the module .
V AIO Digital Studio™ System Reference Manual 40 12 Replace the AGP card and secur e using the screw r emoved earlier . 13 Replace the power supply (see “Replacing the Power Supply” on page 51). 14 Replace the side cover (see “ R e p l a c i n gt h eS i d eC o v e r ” on page 29).
Removing, Installing, and Replacing Components 41 Removing a Memory Module Y ou may need to remove a memory module if you change the memory configuration or replace a bad module. The computer ships with no empty sockets. It comes with a pair of RIMM modules and a pair of CRIMM modules.
V AIO Digital Studio™ System Reference Manual 42 5 Grasp one edge of the memory module and lift out. Store the module in a static-free bag. ! Empty sockets must be filled with either RIMM or CRIMM modules in pairs .
Removing, Installing, and Replacing Components 43 Removing a Slot Cover Y o ur e m o v eas l o tc o v e rw h e ny o ui n s t a l la na d d - i nc a r dt h a to c c u p i e sa previously-empty slot. 1 R e m o v et h es i d ec o v e r( s e e “Removing the Side Cover” on page 28).
V AIO Digital Studio™ System Reference Manual 44 Covering an Open I/O Slot Slot covers prevent air fr om escaping through the empty hole. If air escapes, the components inside the computer cannot be properly cooled. This may damage some components, especially the main processor (which generates the most heat).
Removing, Installing, and Replacing Components 45 Installing a 3.5-inch Internal Hard Disk Drive Models that have only one hard disk drive have an available bay to hold an additional 3.5-inch hard disk drive. The drive you install must not requir e fro nt panel access.
V AIO Digital Studio™ System Reference Manual 46 T o install a 3.5-inch internal hard disk drive (all models) 1 Configure the jumpers on the new drive as a slave device (see your drive’s documentation for configuration instructions). 2 Remove the side cover (see “Removing the Side Cover” on page 28).
Removing, Installing, and Replacing Components 47 6 S l i d et h ed r i v eh o l d e ru pa n do u t . 7 Slide the new drive into the bottom part of the drive holder and align the holes on each side of the drive holder .
V AIO Digital Studio™ System Reference Manual 48 10 Push in on the tab (A) to securely latch the holder to the chassis. 11 Connect the inner drive cable connector (B) to the first drive. 12 Connect the outer drive cable connector (C) to the second drive.
Removing, Installing, and Replacing Components 49 T o set up the new hard drive with the startup disk (PCV -RX490TV model only) Follow these steps to help support Giga Pocket functions in your new hard disk drive. 1 Insert the startup floppy disk into the floppy disk drive.
V AIO Digital Studio™ System Reference Manual 50 Removing the Power Supply Y ou remove the power supply when you insert a memory module (see “Installing System Memory” on page 37). 1 Remove the screw that secur es the power supply to the r ear of the chassis.
Removing, Installing, and Replacing Components 51 Replacing the Power Supply 1 Rotate the power supply down and slide it down along the rails on each side of the chassis opening. 2 Replace the screw that secur es the power supply to the rear of the chassis.
V AIO Digital Studio™ System Reference Manual 52.
53 Chapter 4 System Board This chapter identifies each component on the system board and provides a detailed description of each header , connector , and jumper on the system board.
V AIO Digital Studio™ System Reference Manual 54 Connectors and Headers Front Panel Header T h ef r o n tp a n e lh e a d e ri sa2 0 - p i nh e a d e r( o n ep i ni sr e m o v e df o rt h ek e y ) that provides connections to various fr ont panel functions.
System Board 55 Floppy Disk Drive Header Floppy Disk Drive header Pin Signal Name Pin Signal Name 1G r o u n d 2H D s e l 3G r o u n d 4N . C . 5 Ground 6 DRIVE_SELECT_#3 7G r o u n d 8I N D E X 9 G round 10 DRIVE_SELECT_#0 1 1 Ground 12 DRIVE_SELECT_#1 13 Ground 14 DRIVE_SELECT_#2 15 Ground 16 N.
V AIO Digital Studio™ System Reference Manual 56 Memory Module (RIMM) Slots Be sure to orient a RIMM module such that pin 1 of the RIMM module is o n t h es a m es i d ea sp i n1o ft h es l o t .T h eR I M Mm o d u l es h o w s" A 1 "o n the pin 1 end, and the system board shows “Pin 1” next to the pin 1 end of the slot.
System Board 57 PCI Slots There ar e a total of three PCI slots (slot No. 1 to No. 3). In all models, PCI slot No. 1 is occupied by the fax/modem car d. Y our modem may look differ ent depending on whether it is a Lucent modem or an HPNA modem. In models PCV -RX462DS/PCV -RX463DS/PCV -RX465DS/ PCV -RX470DS/PCV -RX480DS, PCI slot No.
V AIO Digital Studio™ System Reference Manual 58 AGP Slot There is one AGP slot (slot No. 4) that supports a 2x/4x AGP graphics ca rd an d an A GP re t en ti on m od ul e .
System Board 59 IDE Headers There ar e two IDE (Integrated Drive Electronics) headers on the system board: a Primary IDE and a Secondary IDE header . Each 40-pin IDE header supports up to two IDE drives using a ribbon cable with two connectors.
V AIO Digital Studio™ System Reference Manual 60 Power Supply and Aux Power Headers The power supply header on the system boar d connects to the power supply header labelled P1. Power Supply header Pin Signal Name 1+ 3 . 3 V 2+ 3 . 3 V 3G r o u n d 4+ 5 V 5G r o u n d 6+ 5 V 7G r o u n d 8 PWRGD (Power Good) 9+ 5 V S B 10 +12 V 11 + 3 .
System Board 61 17 Ground 18 No Connection 19 +5 V 20 +5 V Aux Power header Pin Signal Name 1G r o u n d 2G r o u n d 3+ 1 2 V 4+ 1 2 V Power Supply header (cont.
V AIO Digital Studio™ System Reference Manual 62 Keyboard and Mouse Ports T h ek e y b o a r dp o r ta n dt h em o u s ep o r ta r e6 - p i nf e m a l e PS/2-type (mini-DIN) ports.
System Board 63 USB Ports and USB Header There ar e four USB ports: two USB ports at the r ear panel, and two USB ports at the front panel. Each permits connection of USB peripheral devices directly to the system without having to use an external hub.
V AIO Digital Studio™ System Reference Manual 64 USB23 header (connects to USB1 on front panel) Pin Signal Name 1+ 3 V D u a l 2N P 1 3N P 3 4N C ( K e y ) 5U S B V C C 1 6U S B V C C 2 7L P 2 + 8L .
System Board 65 Ethernet Port There is one Ethernet port at the r ear panel, which permits connection to a 10Base-T/100Base-TX Ethernet network. Serial , Printer , and i.LINK Ports The serial, printer , and i.LINK ports are mounted in a single bracket on the system board.
V AIO Digital Studio™ System Reference Manual 66 The 6-pin i.LINK port on the back of the system can supply power from the computer to a device if the device also has a 6-pin port. The 6-pin port supplies 10 V to 12 V and a maximum power of 6 watts.
System Board 67 Printer port Pin Signal Name 1S T R O B E - 2D A T A B I T 0 3D A T A B I T 1 4D A T A B I T 2 5D A T A B I T 3 6D A T A B I T 4 7D A T A B I T 5 8D A T A B I T 6 9D A T A B I T 7 10 A.
V AIO Digital Studio™ System Reference Manual 68 i.LINK port Pin Signal Name 1G r o u n d V P ( P o w e r ) * 2G r o u n d 3T P B 4T P B 5T P A 6T P A * Uses over-current protector.
System Board 69 Fan Headers The CPU-F AN and PWR-F AN headers are 1 x 3-pin straight headers. CPU-F AN controls the cooling fan on the CPU. PWR-F AN controls the cooling fan in the power supply .
V AIO Digital Studio™ System Reference Manual 70 Game Port The game port is a female DB-15 port for connecting to a game controller/joystick or MIDI device.
System Board 71 Headphones, Line In, Mic Jacks The headphones jack is a stereo mini-jack (3.5 mm) that connects to headphones. The line in jack is a ster eo mini-jack (3.5 mm) that connects to a s te reo a u di o so urc e (n ot a n au di o s ou rce f rom a v id eo d ev i ce ).
V AIO Digital Studio™ System Reference Manual 72 i.LINK Headers The system board has t wo i.LINK headers: 1394HEAD2 and 1394HEAD3. An internal cable connects the 8-pin header (1394HEAD3) to an interface unit mounted behind the front of the chassis. The interface unit connects to the 4-pin i.
System Board 73 CD-IN Header The CD-IN header on the system board is a 1 x 4-pin header that connects to the DVD-ROM drive’s audio output connector (not used in the PCV -RX490TV).
V AIO Digital Studio™ System Reference Manual 74 AUX-IN Header The AUX-IN header on the system board is a 1 x 4-pin 2mm inline header . It is only used by the Giga Pocket card in the PCV -RX490TV.
System Board 75 Video Header The V ideo header on the system board is a 1 x 4-pin 2mm inline header . It is not used. VIDEO header Pin Signal Name 1V i d e o L 2G r o u n d 3G r o u n d 4V i d e o R V.
V AIO Digital Studio™ System Reference Manual 76 CLR CMOS Jumper The CLR CMOS Jumper clears the BIOS password setting. CLR CMOS Jumper settings Jumper Plug Position Function 2-3 Normal 1-2 Clear CMOS Password ✍ T he configuration jumpers should never need changing unless otherwise directed by a technical support of service technician.
77 Chapter 5 Fax/Modem Card The fax/modem card occupies PCI slot No. 1. Y o ur computer is either installed with a HomePNA modem or Lucent 1648 modem depending on the configuration you purchased. T o determine the modem installed on your computer , locate the RJ-1 1 jacks on the back of your system.
V AIO Digital Studio™ System Reference Manual 78 HomePNA Modem The HomePNA standard uses fr equency division multiplexing (FDM) to u s et h es a m ep h o n el i n ef o rv o i c ea n dd a t at r a n s m i s s i o n .T h i se n a b l e s network access for any compatible HomePNA device that can be plugged into a phone jack (RJ-1 1) in your home.
Fax/Modem Card 79 Lucent 1648 Modem There ar e two RJ-1 1 jacks: one to connect a telephone line, a nd one to connect a phone. Connectors Name Connector T ype Description T elephone RJ-1 1 Connects to.
V AIO Digital Studio™ System Reference Manual 80.
81 Chapter 6 Giga Pocket Card The Giga Pocket card occupies PCI slot No. 2 in the PCV -RX490TV model. The Giga Pocket card has seven connectors and ten pins.
V AIO Digital Studio™ System Reference Manual 82 Connector Description Pin6 Pin7 Pin8 Pin9 Pin10 CN1 CN2 Ground V ideo-Out CN3 CN4 Ground V ideo-In CN5 CN8 CN9 V ideo- In (Front) Ground L-In (Front).
83 Chapter 7 V ideo Card The video card occupies slot No. 4 (AGP slot). The video car d has two p o r t s :as t a n d a r dV G A - s t y l ep o r t ,a n daD V Ip o r t . The VGA-style port is a standard 15-pin high-density VGA-style port on the rear bracket.
V AIO Digital Studio™ System Reference Manual 84 Connectors DVI p ort Pin Signal 1 TMDS data2- 2 TMDS data2+ 3 TMDS data2/4 shield 4 TMDA data4- 5 TMDA data4+ 6D D C c l o c k 7 DDC data 8N C 9 TMDS.
85 Chapter 8 CMOS Setup Options This chapter describes each screen in the A ward BIOS Setup Utility (see “Accessing the BIOS Setup Utility” on page 22). The A ward BIOS setup has five menu items on the menu bar . These are: ❑ Main ❑ Advanced ❑ Power ❑ Boot ❑ Exit Options that you can change are enclosed in brackets.
V AIO Digital Studio™ System Reference Manual 86 Press F10 to save the c hanges and exit, or press Esc to discard the changes. Follow the on-screen pr ompts for other choices. The bottom of the screen presents a s ummary of the keys to use for navigation and contr ol.
CMOS Setup Options 87 Main Screen System Time [00:00:00] System Date [01/01/2001] Primary Master (see “IDE Sub-Menus” on page 88) Primary Slave (see “IDE Sub-Menus” on page 88) Secondary Maste.
V AIO Digital Studio™ System Reference Manual 88 IDE Sub-Menus Type [Auto] User Type HDD CD-ROM LS-120 ZIP-100 MO Other ATAPI None Translation Method * [LBA] Large Normal Match Partition Table Manua.
CMOS Setup Options 89 Advanced Screen CPU Internal Frequency [1500MHz] * I/O Device Configuration (see “I/O Device Configuration Sub-Menu” on page 90) PCI Configuration (see “PCI Configuration Sub-Menu” on page 91) * Depends on model.
V AIO Digital Studio™ System Reference Manual 90 I/O Device Configuration Sub-Menu Onboard AC97 Audio Controller [Enabled] Disabled Onboard 1394 Controller [Enabled] Disabled Onboard Lan Controller .
CMOS Setup Options 91 PCI Configuration Sub-Menu Slot 1 IRQ [Auto] to NA Slot 3 IRQ 3 4 5 7 9 10 11 12 14 15 VGA BIOS Sequence [PCI/AGP] AGP/PCI Onboard LAN Boot ROM [Disabled] Enabled.
V AIO Digital Studio™ System Reference Manual 92 Power Screen Power Up Control AC PWR Loss Restart [Disabled] Enabled PWR Up On Modem Act [Disabled] Enabled Wake On LAN [Disabled] Enabled Hardware M.
CMOS Setup Options 93 Boot Screen 1. ATAPI CD-ROM [(displays installed drive)] Disabled 2. Removable Device [Legacy Floppy] LS120 ZIP-100 ATAPI MO Disabled 3.
V AIO Digital Studio™ System Reference Manual 94 Exit Screen Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes.
95 Chapter 9 Miscellaneous T echnical Information This chapter contains information on the following subjects: ❑ User and Supervisor password ❑ Beep code error messages ❑ PCI configuration statu.
V AIO Digital Studio™ System Reference Manual 96 User and Supervisor Passwords The system allows you to specify up to two passwords (a User passwor d and a Supervisor password) in the CMOS Setup Utility . The User password is r equir ed; the Supervisor password is optional.
Miscellaneous Technical Information 97 Beep Code Error Messages During a normal bootup, a single short beep signifies that the system is OK. Other beep patterns signify errors.
V AIO Digital Studio™ System Reference Manual 98 PCI Configuration Status and Error Messages The following is a list of status and error messages that may appear on your system from time to time. Message Meaning Floppy Disk Controller Resource Conflict The floppy disk controller has requested a resour ce that is already in use.
Miscellaneous Technical Information 99 Static Device Resource Conflict A non-Plug and Play ISA card has requested a resour ce that is already in use. System Board Device Resour ce Conflict A non-Plug and-Play ISA card has requested a resour ce that is already in use.
V AIO Digital Studio™ System Reference Manual 100 DMA Channel Assignments This shows the factory default values. W indows reassigns resour ces to best meet the needs of a particular configuration. DMA Channel Default Assignment 02 Standard floppy disk controller .
Miscellaneous Technical Information 101 System I/O Address Map PCV -RX462DS/PCV -RX463DS/PCV -RX465DS/PCV -RX470DS/PCV -RX480DS Address Range (hex) Description 0x0000-0x000F Direct memory access contr.
V AIO Digital Studio™ System Reference Manual 102 0x0376-0x0376 Secondary IDE controller (dual FIFO) 0x0376-0x0376 Intel 82801BA Ultra A T A storage contr oller 0x0378-0x037F Printer port (LPT1) 0x0.
Miscellaneous Technical Information 103 PCV -RX490TV Address Range (hex) Description 0x0000-0x000F Dir ect memory access controller 0x0010-0x001F Motherboar d r esources 0x0020-0x0021 Programmable int.
V AIO Digital Studio™ System Reference Manual 104 0x0378-0x037F Printer Port (LPT1) 0x03B0-0x03BB NVIDIA GeForce2 MX (Sony) 0x03C0-0x03DF NVIDIA GeForce2 MX (Sony) 0x03F0-0x03F1 Motherboard resource.
Miscellaneous Technical Information 105 Memory Map PCV -RX462DS/PCV -RX463DS/PCV -RX465DS/PCV -RX470DS/PCV -RX480DS Address range Default configuration 0x0000-0x9FFFF System board extension for ACPI B.
V AIO Digital Studio™ System Reference Manual 106 0xF0000000-0xF7FFFFFF NVIDIA GeForce2 MX (Sony) 0xEF000000-0xEF00FFFF NVIDIA GeForce2 MX (Sony) 0xEB800000-0xEDFFFFFF Intel® 82801BA PCI Bridge - 2.
Miscellaneous Technical Information 107 IRQ Summary PCV -RX462DS/PCV -RX463DS/PCV -RX465DS/PCV -RX470DS/PCV -RX480DS IRQ Description 0 System timer 1 Standard 101/102-Key or Microsoft Natural Keyboar .
V AIO Digital Studio™ System Reference Manual 108 PCV -RX462DS/PCV -RX463DS/PCV - RX465DS/PCV -RX470DS/PCV -RX480DS IRQ Description 0 System timer 0 System timer 1 Standard 101/102-Key or Micr osoft.
109 Chapter 10 Specifications This chapter describes the technical specifications for the Sony PCV -RX462DS/PCV -RX463DS/PCV -RX465DS/PCV -RX470DS/ PCV -RX480DS/PCV -RX490TV computers. Processors Chipset AGP Bus PCV -RX462DS 1.3 GHz Intel® Pentium® 4 processor PCV -RX463DS/PCV -RX465TV 1.
V AIO Digital Studio™ System Reference Manual 110 PCI Bus Memory Modules Memory Configurations L2 Cache Graphics PCI Level 2.2, 33 MHz zero wait state 3 PCI slots (2 open in the PCV -RX462DS/PCV -RX.
Specifications 111 Audio Sound chip Analog Devices SoundMAX integrated digital audio W ave synthesis Software synthesis Sound effects DirectX® Audio sampling rate Up to 48 kHz at 16 bits Rear panel c.
V AIO Digital Studio™ System Reference Manual 112 Communications Giga Pocket I/O (PCV -RX490TV only) I/O and Expansion Slots Modem Lucent 1648 technology V .90-compatible data/fax modem (REN 0.79B) * * This modem is capable of downloading at 56 Kbps using K56flex™ technology/V.
Specifications 113 Floppy Disk Drive and Controller Hard Drives and Controllers PCI slots T wo available slots in PCV -RX462DS/ PCV -RX463DS/PCV -RX465DS/PCV -RX470DS/ PCV -RX480DS models. One available slot in PCV -RX490TV. Maximum length for add-in cards is 9.
V AIO Digital Studio™ System Reference Manual 114 Optical Drives PCV -RX462DS/PCV -RX463DS/PCV -RX465DS/PCV-RX470DS/PCV -RX480DS Drive Description DVD-ROM drive * * The DVD-ROM data transfer standard 1X rate is 1350 KBps.
Specifications 115 PCV -RX490TV Drive Description DVD-R W drive * * The DVD-ROM data transfer standard 1X rate is 1350 KBps. The CD-RW/CD-R/CD-ROM data transfer standard rate is 150 KBps.
V AIO Digital Studio™ System Reference Manual 116 System BIOS Make and model A ward-based ROM 2Mbit flash-ROM * * Flash-ROM update utility is available from Sony’s web site at http://www.sony.com/pcsupport. Passwords User and supervisor passwords supported Power management APM 1.
117 Index A address map, system 101 AGP bus specifications 109 audio specifications 111 AUX-IN connector 74 B battery - See lithium battery beep codes 97 BIOS Setup Utility See CMOS Setup Utility BIOS.
V AIO Digital Studio™ System Reference Manual 118 installing additional 3.5 drive 45 DVD-ROM drive performance of discs 3 , 4 , 114 , 115 E error messages beep codes 97 PCI configuration 98 expansio.
119 microprocessor - See processor model numbers ii modem - See Also communications modem card connectors 78 , 79 view of 78 , 79 , 83 monitor - See display monitor connector 14 mouse connector 13 , 6.
V AIO Digital Studio™ System Reference Manual 120 printer connector 65 Serial connector 65 USB connectors 63 , 65 system I/O address map 101 system memory, installing 37 T Telephone Consumer Protect.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sony PCV-RX462DS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sony PCV-RX462DS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sony PCV-RX462DS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sony PCV-RX462DS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sony PCV-RX462DS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sony PCV-RX462DS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sony PCV-RX462DS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sony PCV-RX462DS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
