
LCD MONITOR LCD FARBMONITOR MONITEUR LCD MONITOR LCD MONITOR LCD!"====!=EiiJqNRdNF






pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the distance between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B computing equipment.
SHARP LCD Color Monitor LL-T15G1 / LL-E15G1 This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference re- ceived, including interference that may cause undersized operation.
* As an ENERGY STAR Partner, SHARP has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance:www.eiae.org


Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adapta- tion of goods and services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emis- sions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy.
What does labelling involve? This product meets the requirements for the TCO'99 scheme which provides for international and environ- mental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administra- tion). Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric and magnetic fields, energy consumption and electrical and fire safety. The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy. The energy requirements include a demand that the computer and/or display, after a certain period of inac- tivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reacti- vate the computer shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability. Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from:

TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): [email protected] Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproduc- tive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available.
Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 require- ment states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium.
Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available.
CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.
Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO´99 requirement permits the inclusion of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla direttiva 93/68/EEC.
Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ 73/23/ΕΟΚ, óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras av 93/68/EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/ EEC.
VARNING : FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

FOR CUSTOMERS IN U.K.
GREEN-AND-YELLOW: Earth BLUE: Neutral BROWN: Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows. The wire which is coloured GREEN- AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth or coloured green or green-and-yellow. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. Ensure that your equipment is connected correctly-if you are in any doubt consult a qualified electrician. "WARNING :THIS APPARATUS MUST BE EARTHED"
Please contact your dealer for service if required or contact Sharp Corporation of Australia on 1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.

- The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor. - Do not leave the screen displaying idly for long periods of time, as this could cause afterimage to remain. - If the brightness is adjusted to the minimum setting it may be difficult to see the screen. - The quality of the computer signal may influence the quality of the display. We recommend using a computer able to emit high quality video signals. - Never rub or tap the monitor with hard objects. - Please understand that Sharp Corporation bears no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law. - This monitor and its accessories may be upgraded without advance notice.
Monitor and accessory checklist - Please check that the following items are included in the package.
- LCD monitor (1) - AC adapter (1) (model name: NL-A60J , color: gray) - RGB signal cable (1) - Utility Disk (For Windows/Macintosh) (1) - Operation manual (1)
Use of AC adapter - Do not use the AC adapter for other than the specified equipment. - Unplug the AC adapter if it is not used for long time. - Do not place any objects on the AC adapter. - Do not use the AC adapter outdoors. - Do not attempt to repair the AC adapter if it is broken or malfunctioning. Refer the servicing to the service representative. - Do not try to open the AC adapter. - Do not use water or wet cloth for cleaning the AC adapter.
Location - Do not use the monitor where ventilation is poor, where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil or steam, as this could lead to fire. - Ensure that the monitor does not come into contact with water or other fluids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fire or electric shock. - Do not place the monitor on top of unstable objects or in unsafe places. Do not allow the monitor to come into contact with strong shocks or vibrations. Causing the monitor to fall or topple over may damage it. - Do not use in places where the monitor will be subject to direct sunlight, near heating equipment or anywhere else where there is likelihood of high temperature, as this may lead to generation of excessive heat and outbreak of fire.
Manual Scope - In this booklet, Microsoft Windows XP will be referred to as [WindowsXP], Microsoft Windows Millenium as [WindowsMe], Microsoft Windows 2000 as [Windows2000], Microsoft Windows 98 as [Windows98], Microsoft Windows 95 as [Windows95], and Microsoft Windows Version 3.1 as [Windows3.1]. When there is no need to distinguish between programs, the term [Windows] will be used. - Microsoft and Windows are registered trademarks of Microsoft Corporation. - Macintosh is a registered trademark of Apple Computer, Inc.
The Power Cord - Do not damage the power cord nor place heavy objects on it, stretch it or overly bend it. Also, do not add extension cords. Damage to the cord may result in fire or electric shock. - Use only the AC adapter supplied with the monitor. Using an AC adapter other than that supplied may lead to fire. - Insert the power plug directly into the AC outlet. Adding an extension cord may lead to fire as a result of overheating.

1 2 3 4 5
Control Panel

Adjusting the monitor Press down on the stand and adjust it to a suitable viewing angle.
approx.25° approx.5°
- Pressure from hands on the LCD panel could cause damage.
Standing up the monitor Press down on the stand and lift up the top section of the monitor.
Folding up the monitor 1. Remove the AC adapter and the RGB signal cable. 2. Press down on the stand and gently fold back the monitor.
- Be careful not to pinch your fingers.
- Be careful not to pinch your fingers. - Do not use the monitor when tilted back beyond approximately 25º.The monitor may fall over leading to injury or malfunction.
- When raising the display section, movement becomes harder in the middle of travel. Continue raising by applying more force at that point. - When the monitor is used with an arm mounting, movement becomes stiffer to keep the display section from tipping over. This is not a malfunction.
approx.25° approx.5°
Prohibited range


Connecting the monitor to a power source
Before connecting, first turn off the monitor's main power switch.
When connecting, ensure that both the monitor and computer are switched off.

Firmly insert the analog RGB terminal (mini D-sub 15 pin with 3 rows) then tighten the screws each side.

If connecting to a D-sub 15 pin 2 row Apple Power Macintosh, attach a Macintosh conver- sion adapter (to be purchased separately) to the RGB signal cable.
RGB signal cable After connecting the adapter, tighten the screws on each side to fix into place.
Turn on device to which monitor is connected
AC terminal · Power cord · Press power button

Installing set-up information and the ICC profile (for Windows) Depending on the computer or OS, it may be neces- sary to use the computer to operate the installation of monitor set-up information etc. If so, follow the steps below to install the monitor set-up information. (Depending on the type of computer or OS, com- mand names and methods may differ. Please follow the computer’s own operation manual while reading this.)
About the ICC profile An ICC (International Color Consortium) profile is a file that describes the color characteristics of the LCD monitor. By using an application that works together with an ICC profile, a high color resolution can be realized. - Windows98/2000/Me/XP all use the ICC profile. - When installing Windows98/2000/Me/XP set- up information (described below), the ICC profile is also installed. If you would like to install the ICC program only, please refer to Installing the ICC profile on page 15. - When using the ICC profile, please set the [WHITE BALANCE] to [STD] .
Turn off device to which monitor is connected
Installing monitor set-up information into Windows95. This explanation assumes that the floppy disk drive is "A drive".
1. Place the Utility Disk (provided) into the compu- ter's A drive. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings], [Advanced Properties], and [Monitor], then [Change]. 5. Click on [Have disk], confirm that [Copy manufac- turer's files from:] is [A:] then click [OK]. 6. Confirm that the monitor details are selected, and click [OK]. 7. Check that the monitor details are displayed, then click [Apply]. 8. Click [OK], and close the window. 9. Remove the Utility Disk from the A drive.
Press power button · Installing set-up information · For Windows95

Installing monitor set-up information into Win- dows98, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the floppy disk drive is "A drive".
Installing monitor set-up information into Win- dows2000, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the floppy disk drive is "A drive".
If the "Add new Hardware Wizard" has appeared:
1. Place the Utility Disk (provided) into the compu- ter's A drive. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings], [Advanced] and [Monitor]. 5. Click on [Properties], [Driver] and [Update Driver]. 6. When [Upgrade Device Driver Wizard] appears, click [Next]. 7. Check [Display a list of the known drivers for this device so that I can choose a specific driver] and click [Next]. 8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [A:], and click [OK]. 9. Select the monitor from the list displayed and click [Next]. 10.Click [Next], confirm that the monitor's name appears on the screen, and click [Finish]. If [The Digital Signature Not Found] appears, click [Yes]. 11.Click on [Close]. 12.Click [OK], and close the window. 13.Remove the Utility Disk from the A drive.
1. Place the Utility Disk (provided) into the compu- ter's A drive. 2. Click [Next]. 3. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next]. 4. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [A:], and click [OK]. 5. Confirm that the monitor details are selected, then click [Next], [Next], and [Finish]. If the "Add New Hardware Wizard" appears, repeat the installation commands beginning from 2 above. 6. Remove the Utility Disk from the A drive.
If the "Add New Hardware Wizard" has not ap- peared:
1. Place the Utility Disk in the computer's A drive. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings], [Advanced] and [Monitor]. 5. In [Options], check [Automatically detect Plug & Play monitors] and click on [Change]. 6. Click [Next]. 7. Click on [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next]. 8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [A:], and click [OK]. 9. Confirm that the monitor details are selected, then click [Next], [Next], and [Finish]. 10.Check that the monitor details are displayed, then click [Apply]. 11.Click [OK], and close the window. 12.Remove the Utility Disk from the A drive.
Installing monitor set-up information into WindowsMe, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the floppy disk drive is "A drive".
If the "Add new Hardware Wizard" has appeared:
For Windows98 · For Windows2000 · For WindowsMe

10.Select the monitor from the list displayed and click [Next]. If [has not passed Windows Logo testing...] appears, click [Continue Anyway]. 11.Confirm that the monitor's name appears on the screen. 12.Click on [Finish]. 13.Click on [Close]. 14.Click [OK], and close the window. 15.Remove the Utility Disk from the A drive.
If the "Add New Hardware Wizard" has not ap- peared:
1. Place the Utility Disk in the computer's A drive. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings], [Advanced] and [Monitor]. 5. In [Options], check [Automatically detect Plug & Play monitors] and click on [Change]. 6. Check [Specify the location of the driver [Advanced]] and click [Next]. 7. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.] and click [Next]. 8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [A:], and click [OK]. 9. Select the monitor details, then click [Next], [Next], and [Finish]. 10.Check that the monitor details are displayed, then click [Apply]. 11.Click [OK], and close the window. 12.Remove the Utility Disk from the A drive.
Installing the ICC profile Installing the monitor’s ICC profile. (If the set-up information has already been installed, so too has the profile, and there is no need to install it.) This explanation assumes that the floppy disk drive is "A drive".
1. Place the Utility Disk in the computer’s A drive. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings] and [Advanced]. 5. Click on [General] and from [Compatibility] select [Apply the new display setting without restarting], then click on [Color Management]. 6. Click [Add], and select [3 ½ Floppy [A:]] as the file location. 7. Choose the color profile that you would like to install, and click on [Add]. 8. Choose the profile and click on [Set As Default]. 9. Click [OK], and close the window. 10.Remove the Utility Disk from the A drive.
Installing monitor set-up information into WindowsXP, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the floppy disk drive is "A drive".
- When using the ICC profile, please set the [WHITE BALANCE] to [STD].
1. Place the Utility Disk in the computer's A drive. 2. Click on the [Start] button. Choose [Control Panel]. 3. Switch to "Classic View". 4. Double click on [Display]. 5. Click on [Settings], [Advanced] and [Monitor]. 6. Click on [Properties], [Driver] and [Update Driver]. 7. When [Hardware Update Wizard] appears, check [Install from a list or specific location [Advanced]] and click [Next]. 8. Check [Don't search. I will choose the driver to install.] and click [Next]. 9. Click on [Have Disk], confirm that [Copy manufacturer's files from:] is [A:], and click [OK].
For WindowsXP

About the ColorSync profile ColorSync is the Apple Corporation's color man- agement system and is a function that enables color resolution to be realized when used with a compatible application. A ColorSync profile describes the color characteristics of the LCD monitor. Notes: - This monitor's ColorSync profile works with MacOS8.5 or above. - When using the ColorSync profile, please set the [WHITE BALANCE] to [STD] .
Setting up the ColorSync profile

Adjustment the backlight (right column) Brightness of backlight can be adjusted.
Adjustment lock function By disabling the control buttons (i.e. setting the lock) any attempted changes to adjusted values will be voided. 1. Turn off the monitor power. 2. While pressing the MENU button, press the power button (i.e. turn the power on). Continue to press the button until the message appears on the screen. When the menu is unlocked: [ADJUSTMENT LOCKED] will appear on the screen, and the lock will be set. When the menu is locked: [ADJUSTMENT UNLOCKED] will appear on the screen, and the lock will be removed.
Automatic screen adjustment (p.18) The CLOCK, PHASE, H-POS (horizontal position- ing) and V-POS (vertical positioning) functions can be adjusted automatically.
Manual screen adjustment (p. 19) Fine adjustments can be made using the On Screen Display (OSD) Menu.
Resetting all adjustment values All adjustment values can be returned to their original ex-factory values in one command. 1. Turn off the monitor power. 2. Press the MENU button and the SELECT button simultaneously, and while doing this press the power button (i.e. turn the power on). When [ALL RESET] appears on the screen, the reset is complete. 3. Turn off the monitor power.
ADJUSTMENT menu reset The adjustment values of the analogue signal time’s ADJUSTMENT menu can be returned to their original ex-factory values.

Automatic screen adjustment Options in the ADJUSTMENT Menu can be adjusted automatically (CLOCK, PHASE, H-POS V-POS).
Adjusting the screen automatically
CLOCK 127 PHASE 16 H-POS 200 V-POS 29
1 0 2 4 X 7 6 8 V : 7 5 H z H : 6 0 . 0 k H z
Automatic adjustment screen display To perform an automatic adjustment, first display an image that makes the entire screen very bright. If you are using Windows, you can also use the Adjustment Pattern on the accompanying Utility Disk for Windows.
Displaying the Adjustment Pattern (for Windows) This explanation is for Windows 95/98/2000/Me/XP, and assumes that the floppy disk drive is [A drive]. Note: - If the floppy disk drive of your computer is not "A drive", please read the below substituting the floppy disk drive you are using in place of "A drive" or "A". 1. Place the Utility Disk (provided) into the computer's A drive. 2. Open [My Computer] and select [3 ½ Floppy (A:)]. If using Windows 3.1, open [File Manager] and choose "A drive". 3. Double click on [Adj_uty.exe] to run the Adjustment Program. The Adjustment Pattern will appear.
- When further fine adjustment is needed. - When the computer’s video input signals are Composite Sync or Sync On Green. (Automatic adjustments may not be possible.) - When [OUT OF ADJUST] is displayed. (When the screen displays an entirely dark image, the automatic screen adjustment may be disabled. When making an automatic adjustment, be sure to either use the Adjustment Pattern or try displaying an image that makes the entire screen very bright.)
After completing the adjustment, press the computer's [Esc] key to exit the Adjustment Program.
Adjustment pattern

Manual screen adjustment Adjustments can be made using On Screen Display (OSD) Menu provided.

CLOCK 127 PHASE 16 H-POS 200 V-POS 29
1 0 2 4 X 7 6 8 V : 7 5 H z H : 6 0 . 0 k H z MANUAL:Individual menu options are manually
adjusted. AUTO: Every menu option is automatically adjusted.

CLOCK 127 PHASE 16 H-POS 200 V-POS 29
1 0 2 4 X 7 6 8 V : 7 5 H z H : 6 0 . 0 k H z At this point relevant menu options can be adjusted. Each time the MENU button is pressed the next menu is selected. (ADJUSTMENT → GAIN CONTROL → WHITE BALANCE → MODE SELECT → OSD Menu disappears)
CLOCK The figure below demonstrates how to adjust so that vertical flicker noise is not emitted. ( buttons)

PHASE The figure below demonstrates how to adjust so that horizontal flicker noise is not emitted. ( buttons) Note: - Adjustments to PHASE should be made only after CLOCK has been correctly set.
H-POS (horizontal positioning) and V-POS (vertical positioning) To center the screen image within the boundaries of the screen, adjust the left-right (H-POS) values and the up-down (V-POS) values. ( buttons)

WH I TE BALANCE
MANUAL AUTO
COOL STD WARM USER
BL ACK LEVEL 16 CONTRAST 80
R-CONTRAST G-CONTRAST B-CONTRAST
1 0 2 4 X 7 6 8 V : 7 5 H z H : 6 0 . 0 k H z MANUAL:Individual menu options are manually
1 0 2 4 X 7 6 8 V : 7 5 H z H : 6 0 . 0 k H z
adjusted. AUTO: Every menu option is automatically adjusted using the Auto Gain Control* function.
Notes: - On settings other than [STD] not all graduations can be displayed. To display all graduations, set to [STD]. - Use the buttons to select [COOL], [·], [STD], [·], [WARM] or [USER]. - Selecting USER will display the setting values for [R-CONTRAST], [G-CONTRAST] and [B- CONTRAST], in order to make fine adjustments. - Use the SELECT button to select [R-CONTRAST], [G-CONTRAST] and [B-CONTRAST]. - To go to the next menu: MENU button
* Auto Gain Control function - The Auto Gain Control adjusts contrast and black level based on the brightest color of the image displayed. If you are not using the Adjustment Pattern it is necessary to have an area of 5 mm x 5 mm of white displayed, and if not adjustments may not be possible. (In such case, [OUT OF ADJUST] will appear and setting values remain unchanged.) - If the signal coming from the computer is composite sync or sync on green, automatic adjustment cannot be performed. Please perform manual adjustment instead.
USER R-CONTRAST. . . button for blue-green button for red G-CONTRAST . . button for purple button for green B-CONTRAST . . . button for yellow button for blue
BLACK LEVEL Total screen brightness can be adjusted while watching the color pattern. ( buttons)
CONTRAST While watching the color pattern, adjustments can be made so that all graduations appear. ( buttons)
GAIN CONTROL Menu · WHITE BALANCE Menu · Color pattern

COLORS Maximum display colors can be set. ( buttons) 260K (260,000) and 16M (16.19 million)
OS D H-POS I T I ON OS D V-POS I T I ON 4 0 0 L I NES 640 720 SC AL I NG 3 C O L O R S 260K 16M L A NGUAGE
LANGUAGE Messages displayed on the screen and OSD Menu contents can be changed to the following languages.
1 0 2 4 X 7 6 8 V : 7 5 H z H : 6 0 . 0 k H z
Dutch, English, French, German, Spanish, Italian, Swedish. 1. Press the button. The Language Selection Menu will be displayed on the screen. 2. Use the SELECT button to choose a language. 3. Press the MENU button or the button. The setting is complete.
OSD H-POSITION (OSD horizontal position) The position of the OSD display can be moved to the left and right. ( buttons)
OSD V-POSITION (OSD vertical position) The position of the OSD display can be moved up and down. ( buttons)
400 LINES (degree of resolution) You can specify the horizontal resolution of a 400- line screen when using US text, etc. ( buttons)
SCALING (Level of scaling) The sharpness of the image can be adjusted. ( buttons)
Note: - When the display mode is set to less than 1024 x 768 pixels, the display is enlarged to cover the whole screen (i.e. the side ratio of the display may change). - If a resolution of 1024 x 768 pixels cannot be achieved even after expansion is attempted, the screen's perimeter will display black. (This is not a malfunction.)
MODE SELECT Menu

Monitor care Always remove the plug from the AC outlet when cleaning the monitor.
Troubleshooting If you think the monitor may be faulty, please check the following points before taking it to be repaired. If afterwards it still does not work, please contact the shop where you purchased the monitor or your nearest Sharp authorized Service Center.
Cabinet and control panel section Use a soft dry cloth to lightly wipe away any grime from the cabinet and control panel. If they are very dirty, apply neutral detergent to a dampened soft cloth, wring it out well and wipe away grime.
The monitor's florescent tubes have a limited life span. - If the screen darkens, persistently flickers or does not light up, it may be necessary to replace the florescent tube unit. Please inquire at the shop where you purchased the monitor or your nearest Sharp authorized Service Center. (Never attempt this replacement on your own.) - In the initial period of use, due to the characteristics of florescent tubes the screen may flicker. (This is not a malfunction.) Should this happen, check by first turning off the power, then turning it on again.
LCD panel section Use a soft dry cloth to lightly wipe away dirt and dust from the surface of the LCD panel. (A soft cloth such as gauze or that used for lens cleaning is suitable.)
- Never use thinner, benzine, alcohol, glass cleaner, etc, as this could lead to color change or change in shape. - Never scratch the monitor with anything hard or apply strong pressure as this could leave marks or result in malfunction.
No image appears on the monitor (Power LED is not lit) - Are the AC adapter and the power cord connected properly? (p. 12)
Storage If the monitor will not be used for a long period of time, be sure to remove the power plug from the AC outlet.
No image appears on the monitor (Power LED is lit) - Is the computer connected properly? (p. 12) - Is the computer turned on? - Does the computer's signal timing correspond to monitor specifications? (p. 24) - Is the computer in power-saving mode?
- Do not leave the monitor in contact with rubber or plastic items for long periods of time as this could lead to color change or change in shape.
Control buttons do not work - Is the adjustment lock on? (p. 17)
The image appears distorted - Does the computer's signal timing correspond to monitor specifications? (p. 24) - Perform automatic adjustment. (p. 18)

38 cm measured diagonally TFT LCD module Resolution (max.)
XGA 1024 x 768 pixels Displayable colors (max.)
16.19 million colors (6bit + FRC2bit) Brightness (max.)
260cd/m2 Dot pitch
0.297(H) x 0.297(V) mm Contrast ratio
350:1 Angle of visibility
Left-right 160°; Up-down 150° Screen display size
Horizontal 304.1 mm x Vertical 228.1 mm Video signal
Analog RGB (0.7Vp-p) [75Ω] Sync signal
Digital screening (enlargement of display to correct VGA/SVGA) Plug & Play
15 pin mini D-sub (3 rows) Screen tilt
Upward approx.0 - 25°; downward approx.0 - 5° Power supply
AC100-240V, 50/60Hz (Use special AC adapter, type NL-A60J of Sharp Corporation.) Temperature of operating environment
Special AC adapter:
Maximum 35W (3W when in power-saving mode) (Use special AC adapter.) Dimensions (W x D x H)
Approx.1.5m
339 mm x 187 mm x 322 mm Weight
Approx. 3.4 kg (Excluding AC adapter and RGB signal cable.)
Approx. H 124mm x D 62 mm x H 36mm
LCD display

Display mode Hsync Vsync Dot frequency
31.5kHz 60Hz 25.175MHz 640x480 37.9kHz 72Hz 31.5MHz 37.5kHz 75Hz 31.5MHz VESA 35.1kHz 56Hz 36.0MHz
800x600 37.9kHz 60Hz 40.0MHz 48.1kHz 72Hz 50.0MHz 46.9kHz 75Hz 49.5MHz 48.4kHz 60Hz 65.0MHz 1024x768 56.5kHz 70Hz 75.0MHz 60.0kHz 75Hz 78.75MHz US text 720x400 31.5kHz 70Hz 28.3MHz Power Macintosh 640x480 35.0kHz 66.7Hz 30.2MHz series 832x624 49.7kHz 74.6Hz 57.3MHz 1024x768 60.2kHz 75Hz 80.0MHz
Notes: - All are compliant only with non-interlaced. - Frequencies for Power Macintosh are reference values. - If the monitor is receiving timing signals that are not compatible, [OUT OF TIMING] will appear. Follow your computer's instruction manual to set the timing to be compatible with the monitor. - If the monitor is not receiving any signal (synch signal), [NO SIGNAL] will appear.
5 1 2 3 4
1 Red video signal input
10 6 7 8 9
15 11 12 13 14
2 Green video signal input
3 Blue video signal input
Mini D-sub connector with 15 pins
5 GND
6 For red video signal GND
7 For green video signal GND
8 For blue video signal GND
10 GND
11 N.C.
13 For H-sync signal input
14 For V-sync signal input

DDC (Plug & Play)
The monitor is based on VESA DPMS (Display Power Management Signaling). To activate the monitor's Power Management func- tion, both the video card and the computer must conform to the VESA DPMS standard.
This monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for carrying out Plug & Play functions on the monitor or PC. It transfers information such as degree of resolution between the monitor and PC. You can use this function if your PC is DDC compliant and if it is set so that it can detect the Plug & Play monitor. There are many varieties of DDC due to the differ- ences between systems. This monitor works with DDC1 and DDC2B.
DPMS mode Screen Power H-sync V-sync consumption
ON Display on 35W Yes Yes
SUSPEND Display off 3W Yes No
STANDBY No Yes · OFF No No

An arm based on the VESA standard can be at- tached to the monitor. The arm must be purchased separately.

When choosing the arm to be installed please take note of the following points. - The arm should be compatible with the VESA standard, and there must be a gap of 75mm x 75mm between the screw holes on the section to be attached. - The arm must not fall off or break off after being attached to the monitor.
The screws used to attach the arm should be M4 screws with a length of 4 mm ~ 6 mm protrud- ing from the surface to be attached. Using any other kind of screw may lead to the monitor falling off or damage to the internal part of the monitor.


Be careful not to pinch your fingers. 4. Being careful not to damage the monitor, spread out a soft cloth and lay the monitor on it display- side down.


Pagine di riferimento in questo manuale: produttore, supporto e download.
I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.