IT
Sharp logo
Manuale d'uso ufficiale

Sharp LL-191A

148 pagine·4.7 MB·Monitor per computer·PDF·ENNLJA
Sharp LL-191A
Indice dei contenuti 49 sezioni Notice for Users in the USA · English Deutsch Français Italiano Español English · FCC Statement · Declaration of Conformity · … MostraNascondi
Page 1 of the Sharp LL-191A user manual
Pagina 1 · clicca per ingrandire
Pagina 1

LCD Monitor LCD Farbmonitor Moniteur LCD Monitor LCD Monitor LCD

LL-191A OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUALE D'USO MANUAL DE FUNCIONAMIENTO

Sharp LL-191A diagram (page 1)
Fig. 1
Page 2 of the Sharp LL-191A user manual
Pagina 2 · clicca per ingrandire
Pagina 2
Page 2 of the Sharp LL-191A user manual
Page 3 of the Sharp LL-191A user manual — Declaration of Conformity
Pagina 3 · clicca per ingrandire
Pagina 3

Notice for Users in the USA

English Deutsch Français Italiano Español English

Model No.:

Serial No.:

FCC Statement

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the distance between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected. - Consult the dealer or an experienced radio/TV technician for help.

Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B computing equipment.

Declaration of Conformity

SHARP LCD Color Monitor LL-191A-W/LL-191A-B This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible PartySHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430 TEL: 1-800-BE-SHARP

* As an ENERGY STAR® Partner, SHARP has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org

Page 4 of the Sharp LL-191A user manual — Notice for Users in Europe
Pagina 4 · clicca per ingrandire
Pagina 4

Notice for Users in Europe

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla direttiva 93/68/EEC.

Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ 73/23/ΕΟΚ, óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras av 93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/ 68/EEC.

VARNING: FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

Page 5 of the Sharp LL-191A user manual — Service Inquiries
Pagina 5 · clicca per ingrandire
Pagina 5

Notice for Users in the UK

FOR CUSTOMERS IN U.K.

English Deutsch Français Italiano Español English

GREEN-AND-YELLOW : Earth BLUE : Neutral BROWN : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

  • The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth or coloured green or green-and-yellow.
  • The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
  • The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red. Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician. "WARNING: THIS APPARATUS MUST BE EARTHED."

Notice for Users in Australia

Service Inquiries

Please contact your dealer for service if required or contact Sharp Corporation of Australia on 1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.

Page 6 of the Sharp LL-191A user manual — LL-191A-W
Pagina 6 · clicca per ingrandire
Pagina 6
Sharp LL-191A — Congratulations! diagram (page 6)
Fig. 2 · Congratulations!
Sharp LL-191A — Congratulations! diagram (page 6)
Fig. 3 · Congratulations!

Congratulations!

The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment.

LL-191A-W

Some of the features of the TCO'03 Display requirements:

Ergonomics • Good visual ergonomics and image quality in order to improve the working environment for the user

and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability.

  • Energy
  • Energy-saving mode after a certain time – beneficial both for the user and the environment
  • Electrical safety
  • Emissions
  • Electromagnetic fields
  • Noise emissions
  • Ecology
  • The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001
  • Restrictions on - chlorinated and brominated flame retardants and polymers - heavy metals such as cadmium, mercury and lead.

The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world.

For more information, please visit

www.tcodevelopment.com

Page 7 of the Sharp LL-191A user manual — English Deutsch Français Italiano Español English
Pagina 7 · clicca per ingrandire
Pagina 7
Sharp LL-191A — LL-191A-B diagram (page 7)
Fig. 4

English Deutsch Français Italiano Español English

LL-191A-B

Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.

Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (e.g. acidic and climate- influencing emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy.

What does labelling involve? This product meets the requirements for the TCO'99 scheme which provides for international and environmental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric and magnetic fields, energy consumption and electrical and fire safety. The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy. The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability. Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from:

TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): [email protected] Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/

Page 8 of the Sharp LL-191A user manual — LL-191A-B
Pagina 8 · clicca per ingrandire
Pagina 8

Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available.

Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium.

Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available.

CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.

Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed.

* Bio-accumulative is defined as substances which accumulate within living organisms.

** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.

Environmental requirements

Page 9 of the Sharp LL-191A user manual — LL-191A-B
Pagina 9 · clicca per ingrandire
Pagina 9
Page 9 of the Sharp LL-191A user manual — LL-191A-B
Page 10 of the Sharp LL-191A user manual — Tips and safety precautions
Pagina 10 · clicca per ingrandire
Pagina 10

Tips and safety precautions

- The TFT color LCD panel used in this monitor is

The Power Cord - Do not damage the power cord nor place heavy

made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor. - Do not display a still picture for a long time, as

objects on it, stretch it or over bend it. Also, do not add extension cords. Damage to the cord may result in fire or electric shock. - Use only the power cord supplied with the monitor. - Insert the power plug directly into the AC outlet.

Adding an extension cord may lead to fire as a result of overheating. - Do not remove or insert the power plug with wet

hands. Doing so could result in electric shock.

this could cause an afterimage to remain. - If the brightness is adjusted to the minimum

Monitor and accessory checklist - Please check that the following items are

setting it may be difficult to see the screen. - The quality of the computer signal may influence

included in the package. - LCD monitor (1) - Analog signal cable (1)

the quality of the display. We recommend using a computer able to emit high quality video signals. - Never rub or tap the monitor with hard objects. - Please understand that Sharp Corporation bears

(model name0NIT15G4-0015) - Audio cable (1)
(model name0NIT17A3-U006) - Power cord (1) - CD-ROM (1) - Operation manual (1)

no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law. - This monitor and its accessories may be

upgraded without advance notice.

monitor needs to be transported. - Sharp Corporation holds authorship rights to the

Location - Do not use the monitor where ventilation is poor,

Utility Disk program. Do not reproduce it without permission. - The shape of the supplied accessories may not

where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil or steam, as this could lead to fire. - Ensure that the monitor does not come into

be exactly same as shown in this manual.

Manual Scope - In this manual, Microsoft Windows XP will be

contact with water or other fluids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fire or electric shock. - Do not place the monitor on top of unstable

referred to as "Windows XP", Microsoft Windows Millennium as "Windows Me", Microsoft Windows 2000 as "Windows 2000", Microsoft Windows 98 as "Windows 98", Microsoft Windows 95 as "Windows 95", and Microsoft Windows Version 3.1 as "Windows 3.1". When there is no need to distinguish between programs, the term "Windows" will be used. - Microsoft and Windows are registered

objects or in unsafe places. Do not allow the monitor to come into contact with strong shocks or vibrations. Causing the monitor to fall or topple over may damage it. - Do not use in places where the monitor will be

trademarks of Microsoft Corporation. - Macintosh is a registered trademark of Apple

subject to direct sunlight, near heating equipment or anywhere else where there is likelihood of high temperature, as this may lead to generation of excessive heat and outbreak of fire.

Computer, Inc. - All other brand and product names are

trademarks or registered trademarks of their respective holders.

Page 11 of the Sharp LL-191A user manual — Product description
Pagina 11 · clicca per ingrandire
Pagina 11

Product description

Sharp LL-191A — Product description diagram (page 11)
Fig. 5 · Product description
1. AUTO button This button is used to perform automatic adjustment of the screen (CLOCK, PHASE, H-POS and V-POS). (p.18) 2. MENU button This button is used to pop-up, select and close the OSD (On Screen Display) Menu. 3. / MODE button When the OSD Menu is displayed:

This button is used to select menu options. When the OSD Menu is not displayed:

This button is used to set DISPLAY MODE. 4. buttons When the OSD Menu is displayed:

These buttons are used to select an option or adjust the value of the selected option. When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness and speaker volume. 5. Speakers Audio entering via the external device connected to the monitor can be heard. 6. Headphone terminal Headphones (commercially available) can be connected here. 7. Power button Pressing this button turns the power on. Press the button again to turn the power off. 8. Power LED This LED is lit green when in use and orange when in power-saving mode. 9. Main power switch 10. Power terminal 11. Analog RGB input terminal The analog signal cable is connected here. The analog signal cable included should be used. 12. Audio input terminal A computer's audio output terminal can be connected here. The audio cable included should be used. 13. Security lock anchor By connecting a security lock (commercially available) to the security lock anchor, the monitor is fixed so that it cannot be transported. The security slot works in conjunction with Kensington Micro Saver Security Systems. 14. Ventilation openings Never block the ventilation openings as this may lead to overheating inside the monitor and result in malfunction.

Page 12 of the Sharp LL-191A user manual — CAUTION!
Pagina 12 · clicca per ingrandire
Pagina 12

Angle adjustment

CAUTION!

- Be sure to hold both sides of the monitor when

adjusting the viewing angle. The LCD panel used in this monitor is made of glass. Pressure from hands on the LCD panel could cause damage.

approx. 25°

approx. 5°

Page 13 of the Sharp LL-191A user manual — Connecting the monitor and turning the monitor on and off
Pagina 13 · clicca per ingrandire
Pagina 13
Sharp LL-191A — Connecting the monitor and turning the monitor on and off diagram (page 13)
Fig. 6 · Connecting the monitor and turning the monitor on an…

Connecting the monitor and turning the monitor on and off

Connect the accessory audio cable When the accessory audio cable is connected to the audio output terminal of the computer, the sound of the connected computer is output from the monitor speakers. You can also use the headphone jack of the display.

- When connecting, ensure that both the monitor

and computer are switched off. - Be careful not to over bend the cable or add

extension cords as this could lead to a malfunction.

Sharp LL-191A — Connecting the monitor and turning the monitor on and off diagram (page 13)
Fig. 7 · Connecting the monitor and turning the monitor on an…

Connect the accessory analog signal cable to the analog RGB output terminal of the computer.

Analog RGB terminal (Mini D-sub 15 pin, 3 row)

Analog RGB terminal (Mini D-sub 15 pin, 3 row)

- Paying attention to connector direction, firmly

insert the signal cable vertically into the connector, and then tighten the screws at both sides.

If connecting to a D-sub15 pin 2 row Apple Power Macintosh, attach a Macintosh conversion adapter (commercially available) to the analog signal cable.

Sharp LL-191A — Connecting the monitor and turning the monitor on and off diagram (page 13)
Fig. 8 · Connecting the monitor and turning the monitor on an…

conversion adapter (commercially available) may be required.

Page 14 of the Sharp LL-191A user manual — ON
Pagina 14 · clicca per ingrandire
Pagina 14
Sharp LL-191A — Connecting the monitor to a power source diagram (page 14)
Fig. 9 · Connecting the monitor to a power source

Connecting the monitor and turning the monitor on and off

- When switching the main power switch on and

off, always wait for an interval of at least 5 seconds. Rapid switching may result in malfunction.

can be heard from the monitor speakers. - Use headphones with a cable less than 3 m in

2.Press the monitor's power button. 3.Turn on the computer.

length.

Connecting the monitor to a power source

Turn on the computer power supply.

Press power button.

ON

When a signal is input from the computer, the power LED lights up green, and the screen is displayed. (After power is turned on, it may take a little time until the screen is displayed.)

having changed the system settings during use, perform an automatic screen adjustment. (p.18) - Depending on the type of computer or OS, you

may need to install the monitor set-up information on your system. (p.26) - When connecting to a notebook, if the notebook

computer's screen is set to display at the same time, the MS-DOS screen may not display properly. In this case, change the setting to display only the LCD monitor.

Power terminal · AC outlet · Power cord

Page 15 of the Sharp LL-191A user manual — OFF
Pagina 15 · clicca per ingrandire
Pagina 15

Connecting the monitor and turning the monitor on and off

Turning the power off

1.Turn the computer off. 2.Press the monitor's power button. The power LED will disappear.

Turn the computer off. Press power button.

OFF

If the monitor will not be used for a long time, turn off the main power switch of the monitor, and remove the power plug from the outlet.

Page 16 of the Sharp LL-191A user manual — Adjusting the backlight
Pagina 16 · clicca per ingrandire
Pagina 16

Adjusting the screen display and speaker volume

Adjustment lock function By disabling the control buttons (i.e. setting the lock) any attempted changes to adjusted values will be voided. 1.Turn off the monitor power. 2.While pressing the MENU button, press the power button (i.e. turn the power on). Continue to press the buttons until [ADJUSTMENT LOCKED] appears on the screen. The lock is set when the message is displayed.

the power off.

Resetting all adjustment values All adjustment values can be returned to their original ex-factory values in one command. 1.Turn off the monitor power. 2.Press the MENU button and the / MODE button simultaneously, and while doing this press the power button (i.e. turn the power on). Continue to press the buttons until [ALL RESET] appears on the screen. Reset is complete when the displayed message disappears.

the power button are disabled.

Adjustment lock release 1.Turn off the monitor power. 2.While pressing the MENU button, press the power button (i.e. turn the power on). Continue to press the buttons until [ADJUSTMENT UNLOCKED] appears on the screen. The lock is released when the message is displayed.

buttons are disabled. - It is not possible to reset values when the

adjustment lock is in place. Remove the adjustment lock before attempting to operate control buttons.

ADJUSTMENT Menu reset Settings of items in the ADJUSTMENT Menu (CLOCK, PHASE, H-POS, V-POS) can be returned to their original ex-factory values. 1.Turn on the monitor power. 2.Press the MENU button and the button simultaneously. When [RESET] appears on the screen, the reset is complete.

Adjusting the backlight

1.Without the OSD Menu being displayed, press the or the button. 2.Check that [BRIGHT] is selected. If it is not selected, press the / MODE button and select [BRIGHT].

are disabled. - It is not possible to reset values when the

3.Adjust by pressing the button (darker) or button (lighter).

adjustment lock is in place. Remove the adjustment lock before attempting to operate control buttons.

several seconds after the last operation.

Page 17 of the Sharp LL-191A user manual — Checking product information
Pagina 17 · clicca per ingrandire
Pagina 17

Adjusting the screen display and speaker volume

Adjusting the speaker volume

Setting display mode

1.Without the OSD Menu being displayed, press the or the button. 2.Check that [VOLUME] is selected. If it is not selected, press the / MODE button and select [VOLUME].

Color tone or brightness can be changed with one command.

STD

Displays image with the color tone results from original scheme of liquid crystal panel.

OFFICE

Display brightness is lowered. (This mode saves power.)

3.Adjust by pressing the button (decrease) or button (increase).

sRGB is international standard of color representation specified by IEC (International Electrotechnical Commission). Color conversion is made in taking account of liquid crystal's characteristics and represents color tone close to its original image.

several seconds after the last operation.

VIVID

Displays an image with dynamic and vivid primary colors.

- If [DISPLAY MODE] is set to [sRGB] or [VIVID],

[WHITE BALANCE] is set to [STD], and [GAMMA] is set to [0].

How to set Press the / MODE button when the OSD Menu is not displayed. Each time the button is pressed the next menu item appears. (STD → OFFICE → sRGB → VIVID → STD) On Screen display for adjustment disappears several seconds after the last operation.

Checking product information

A model name (MODEL), a serial no. (S/N), and usage time (USAGE TIME) of the monitor can be checked. 1.Turn the power off. 2.While pressing the / MODE button, press the monitor's power button (i.e. turn the power on). The product information will display. 3.Press the MENU button.

purchase may not be 0 (zero), as a result of factory inspection and other activities during manufacture.

sRGB

Page 18 of the Sharp LL-191A user manual — Automatic screen adjustment
Pagina 18 · clicca per ingrandire
Pagina 18
Sharp LL-191A — Automatic screen adjustment diagram (page 18)
Fig. 10 · Automatic screen adjustment

Adjusting the screen automatically Automatic adjustment can be performed using either the AUTO button or the MENU button.

Automatic screen adjustment

Options in the ADJUSTMENT Menu can be adjusted automatically (CLOCK, PHASE, H-POS, V-POS).

AUTO button 1.Press the AUTO button. 2.Press the AUTO button again. [ADJUSTING] will appear on the screen, and after a few seconds [ADJUSTING] will disappear. (The automatic adjustment is now complete.)

after having changed an aspect of the current system, perform an automatic screen adjustment before use.

MENU button 1.Press the MENU button. The ADJUSTMENT Menu will be displayed.

Screen display for adjustment First display an image that makes the entire screen light. If you are using Windows, you can use the Adjustment Pattern on the accompanying CD- ROM.

Sharp LL-191A — Automatic screen adjustment diagram (page 18)
Fig. 11 · Automatic screen adjustment

Opening the Adjustment Pattern (for Windows) This explanation is for Windows 95/98/2000/Me/ XP, and assumes that the CD-ROM drive is "D" drive. 1.Load the accessory CD-ROM into the CD-ROM drive of the computer. 2.Open [My Computer] and select CD-ROM. If using Windows 3.1, open [File Manager] and choose "D" drive. 3.Double click on [Adj_uty.exe] to run the Adjustment Program. The Adjustment Pattern will appear.

2.Press the button. The screen will become dark and [ADJUSTING] will be displayed. After a few seconds the ADJUSTMENT Menu will return. (The automatic adjustment is now complete.) 3.Press the MENU button 5 times to make the OSD (On Screen Display) Menu disappear.

adjustment with the first automatic adjustment. In such a case, try repeating the automatic adjustment 2 or 3 times. - If necessary due to any of the following, manual

adjustments (p.19) can be performed after the automatic adjustment. - When further fine adjustment is needed. - When [OUT OF ADJUST] is displayed. (When

After completing the adjustments, press the computer's [Esc] key to exit the Adjustment Program.

the screen displays an entirely dark image, the automatic screen adjustment may be disabled. When making an automatic adjustment, be sure to either use the Adjustment Pattern or try displaying an image that makes the entire screen very bright.) - When the computer's video input signals are

colors, you may see the different color levels in each color pattern or the gray scale may look colored. (This is due to the specification of the input signal and is not a malfunction.)

Composite Sync or Sync on Green. (Automatic adjustments may not be possible.) - Automatic adjustment may not be achieved

correctly depending on what is displayed on the screen - moving pictures or the MS-DOS prompt etc.

Adjustment Pattern

Page 19 of the Sharp LL-191A user manual — Manual screen adjustment
Pagina 19 · clicca per ingrandire
Pagina 19
Sharp LL-191A — Manual screen adjustment diagram (page 19)
Fig. 12 · Manual screen adjustment

Manual screen adjustment

AUTO When [AUTO] is selected with the button, the [CLOCK], [PHASE], [H-POS] and [V-POS] settings are automatically adjusted.

1.Display an image that makes the entire screen light. (p.18) 2.Display the OSD Menu by pressing the MENU button. ADJUSTMENT Menu

CLOCK The figure below demonstrates how to adjust so that vertical flicker noise is not emitted. ( buttons)

Select the option by pressing the

Sharp LL-191A — Manual screen adjustment diagram (page 19)
Fig. 13 · Manual screen adjustment

/ MODE button.

MENU GAIN CONTROL Menu

Select the option by pressing the

/ MODE button.

PHASE The figure below demonstrates how to adjust so that horizontal flicker noise is not emitted. ( buttons) Note: - Adjustments to [PHASE] should be made only

MENU COLOR CONTROL Menu

Select the option by pressing the

after [CLOCK] has been correctly set.

/ MODE button.

MENU MODE SELECT-1 Menu

Select the option by pressing the

H-POS (horizontal positioning) and V-POS (vertical positioning) To center the Adjustment Pattern within the boundaries of the screen, adjust the left-right (H- POS) values and the up-down (V-POS) values. ( buttons)

/ MODE button.

MENU MODE SELECT-2 Menu

Select the option by pressing the

/ MODE button.

MENU The OSD Menu closes.

approximately 30 seconds after the last command. - This chapter provides the procedure how to

adjust the screen by using Adjustment Pattern (for Windows).

Show 5 more labels / short text on this page
Vertical flicker noise · Horizontal flicker noise · Screen frame · Adjustment · Pattern
Page 20 of the Sharp LL-191A user manual — GAIN CONTROL Menu
Pagina 20 · clicca per ingrandire
Pagina 20

Adjusting the screen display

GAIN CONTROL Menu

COLOR CONTROL Menu

AUTO When [AUTO] is selected with the button, the [BLACK LEVEL] and [CONTRAST] settings are automatically adjusted. After the automatic adjustment, perform manual adjustment when necessary.

WHITE BALANCE 1.After selecting [WHITE BALANCE], press the button. The WHITE BALANCE menu will be displayed.

Sharp LL-191A — GAIN CONTROL Menu diagram (page 20)
Fig. 14 · GAIN CONTROL Menu

BLACK LEVEL Total screen brightness can be adjusted while watching the color pattern. ( buttons)

  • <a href="http://2.Us" rel="nofollow noopener" target="_blank">2.Us</a>e the buttons to select [COOL], [·], [STD], [·], [WARM] or [USER]. COOL ... Color tone bluer than standard
  • ......... Color tone slightly bluer than standard STD ...... Color tone standard setting
  • ......... Color tone slightly redder than standard WARM .. Color tone redder than standard USER

CONTRAST While watching the color pattern, adjustments can be made so that all gradations appear. ( buttons)

- Selecting [USER] will display the setting

values for [R-CONTRAST], [G-CONTRAST] and [B-CONTRAST], in order to make fine adjustments. - Use the / MODE button to select [R-CONTRAST], [G-CONTRAST] and [B-CONTRAST]. R-CONTRAST button for blue-green button for red G-CONTRAST button for purple button for green B-CONTRAST button for yellow button for blue 3.Press the MENU button.

black level based on the brightest and darkest colors of the image displayed. - If you are not using the Adjustment Pattern it is

necessary to have black area and white area of at least 5 mm x 5 mm on the screen. Adjustment may not be possible without those areas. - If the signal coming from the computer is

Composite Sync or Sync on Green, automatic adjustment cannot be performed. Please perform manual adjustment instead. - If [OUT OF ADJUST] is displayed, perform

manual adjustment.

can be displayed. To display all gradations, set to [STD]. - If [DISPLAY MODE] is set to [sRGB] or [VIVID],

no other setting than [STD] can be selected.

GAMMA Adjust so that dark and bright images are easy to see. If the screen is dark and hard to see, increase the numerical value. If it is bright and hard to see, lower the numerical value. ( buttons) - If [DISPLAY MODE] is set to [sRGB] or [VIVID],

[GAMMA] can not be set.

Color pattern

Page 21 of the Sharp LL-191A user manual — MODE SELECT-1 Menu
Pagina 21 · clicca per ingrandire
Pagina 21

Adjusting the screen display

MODE SELECT-1 Menu

MODE SELECT-2 Menu

INFORMATION A model name (MODEL), a serial no. (S/N), and usage time (USAGE TIME) of the monitor can be checked. 1.After selecting [INFORMATION], press the button. The product information will display. 2.Press the MENU button.

even if menu options can be selected, the display may not change.

OSD H-POSITION (OSD horizontal position) The position of the OSD Menu can be moved to the left and right. ( buttons)

OSD V-POSITION (OSD vertical position) The position of the OSD Menu can be moved up and down. ( buttons)

OFF TIMER Power is automatically shut off when the set time elapses. 1.After selecting [OFF TIMER], press the button. 2.Set [ON]/[OFF] by pressing the buttons. If selecting [ON], press the / MODE button and set the shut-off time by pressing the buttons. (Between 1 and 23 hours may be set, by the hour.) 3.Press the MENU button. - When [ON] is selected, the remaining time is

SCALING (Level of scaling) The sharpness of the image can be adjusted. ( buttons) Note: - When the display mode is set to less than

1280 x 1024 pixels, the display is enlarged to cover the whole screen (i.e. the side ratio of the display may change).

displayed in the upper right of the screen during the last 5 minutes before the shut-off. (The remaining time is displayed for approx. 5 seconds, on each minute.) - If the power button is pressed after the first

400LINES (degree of resolution) You can specify the horizontal resolution of a 400- line screen when using US text, etc. ( buttons) 640: 640 x 400 dot mode 720: 720 x 400 dot mode (US text etc.) Note: - As the resolution input for other than 400 lines is

display of the remaining time but before the power shuts off, the OFF TIMER will be set to one hour. To subsequently turn the power off, press the power button again. (When next turning on power, power is again automatically shut off when the set time elapses.) - If the monitor is turned on when the [OFF TIMER]

done automatically, there is no need to set it.

LANGUAGE You can choose the language used in OSD Menu. 1.Press the button. The Language Selection Menu will be displayed on the screen. 2.Use the / MODE button to choose a language. 3.Press the MENU button.

is set to [ON], the set time appears on the display for several seconds. (If there is no input signal, [NO SIGNAL] is displayed.)

Page 22 of the Sharp LL-191A user manual — CAUTION!
Pagina 22 · clicca per ingrandire
Pagina 22

Monitor care

Monitor care

Troubleshooting

Always remove the plug from the AC outlet when cleaning the monitor.

If you think the monitor may be faulty, please check the following points before taking it to be repaired. If afterwards it still does not work, please contact the shop where you purchased the monitor or your nearest Sharp authorized Service Center.

Cabinet and control panel section Use a soft dry cloth to lightly wipe away any grime from the cabinet and control panel. If they are very dirty, apply neutral detergent to a dampened soft cloth, wring it out well and wipe away grime.

The monitor's fluorescent tubes have a limited life span. - If the screen darkens, persistently flickers or

LCD panel section Use a soft dry cloth to lightly wipe away dirt and dust from the surface of the LCD panel. (A soft cloth such as gauze or that used for lens cleaning is suitable.)

does not light up, the fluorescent tube has reached the end of its operational life span. Please inquire at the shop where you purchased the monitor or your nearest Sharp authorized Service Center. - In the initial period of use, due to the

CAUTION!

characteristics of fluorescent tubes the screen may flicker. (This is not a malfunction.) Should this happen, check by first turning off the power, then turning it on again.

- Never use thinner, benzine, alcohol, glass

cleaner, etc, as this could lead to color change or change in shape. - Never scratch the monitor with anything hard or

apply strong pressure as this could leave marks or result in malfunction.

No image appears on the screen (power LED is not lit). - Is the power cord connected properly? (p.14)

Storage

No image appears on the screen (power LED is lit). - Is the computer connected properly? (p.13) - Is the computer turned on? - Does the computer's signal timing correspond to

If the monitor will not be used for a long period of time, be sure to remove the power plug from the AC outlet.

monitor specifications? (p.25) - Is the computer in power-saving mode?

CAUTION!

Control buttons do not work. - Is the adjustment lock on? (p.16)

- Do not leave the monitor in contact with rubber

or plastic items for long periods of time as this could lead to color change or change in shape.

The image appears distorted. - Does the computer's signal timing correspond to

monitor specifications? (p.25) - Perform automatic screen adjustment. (p.18) - If you can change the refresh rate on the

computer you are using, change the value to a lower frequency. (p.25)

No sound can be heard from the speakers. - Is the audio cable connected correctly? (p.13) - Perform the volume adjustment procedure. (p.17) - Are the headphones connected? - There is no sound from the speakers when the

monitor is in power-saving mode (the power LED lights up orange).

Page 23 of the Sharp LL-191A user manual — Information for customers on environmentally friendly disposal of this SHARP product
Pagina 23 · clicca per ingrandire
Pagina 23

Monitor care

Information for customers on environmentally friendly disposal of this SHARP product

If this product cannot be used any more, it should be given away and disposed of in a legally correct and environmentally sound way.

DO NOT DISPOSE OF THIS PRODUCT WITH YOUR HOUSEHOLD WASTE OR MIXED WITH OTHER WASTES ! YOU MIGHT ENDANGER THE ENVIRONMENT !

Sharp Corporation is committed to protecting the environment and conserving energy. Our goal is to minimize the environmental impact of our products by continually implementing and improving product technologies, designs, and customer information aimed at environmental conservation.

(1) For our customers in United Kingdom,

Germany, France, and Italy Please contact your local authorities for collection and recycling facilities, or contact a recycling service company, which is licensed for the recycling of electronic equipment. SHARP recommends the recycling services of MIREC, the General information on MIREC can be obtained from http://www.mirec.com/ MIREC services have to be paid for by the last owner of the electronic equipment in question.

(2) For our customers in the USA

This product utilizes tin-lead solder, and a fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For collection and recycling information, please contact your local authorities or the Electronics Industries Alliance: http://www.eiae.org

(3) For our customers in Japan

Call toll free number 0120-845-530 for recycling Information.

Page 24 of the Sharp LL-191A user manual — Specifications
Pagina 24 · clicca per ingrandire
Pagina 24

Specifications

Product specifications Model name

Dimensions (Unitsmm)

LL-191A-W (White)/LL-191A-B (Black) LCD display

Sharp LL-191A — Specifications diagram (page 24)
Fig. 15 · Specifications

48 cm measured diagonally TFT LCD module Resolution (max.)

SXGA 1280 x 1024 pixels Displayable colors (max.)

Approx.16.19 million colors (6 bit + FRC) Brightness (max.)

0.294 (H) x 0.294 (V) mm Contrast ratio

500:1 Angle of visibility

Left-right 160°; up-down 160° (contrast ratio > 5) Screen display size

Horizontal 376.3 mm x Vertical 301.1 mm Video signal

Analog RGB (0.7 Vp-p) [75Ω] Sync signal

Separate Sync (TTL level+/-), Sync on Green, Composite Sync (TTL level: +/-) Expansion compensation

Digital scaling (Enlarges VGA/SVGA/XGA etc. to full screen size.) Plug & Play

VESA DDC2B compatible Power management

- Analog signal cableapprox. 1.8 m - Audio cable: approx. 1.8 m
VESAbased on DPMS Speaker output

1 W + 1 W Input signal terminal

improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

Mini D-sub15 pin (3 row) Audio input terminal

Mini stereo jack Headphone terminal

Mini stereo jack Screen tilt

Upward approx. 0 - 25°; downward approx. 0 - 5° Power supply

AC100 - 240 V, 50/60 Hz Temperature of operating environment

5. 35°C Power consumption

33 W (with no audio input) (36 W maximum, 1.8 W when in power-saving mode) Dimensions

Approx. 419 (W) x 213 (D) x 409 (H) mm Weight

Approx. 7.8 kg (approx. 5.7 kg excluding stand) (Excluding cables.)

220 cd/m2 · Dot pitch

Page 25 of the Sharp LL-191A user manual — Relevant signal timings
Pagina 25 · clicca per ingrandire
Pagina 25

Specifications

Relevant signal timings

The analog RGB input connector pin (Mini D-sub connector with 15 pins)

Sharp LL-191A — Relevant signal timings diagram (page 25)
Fig. 16 · Relevant signal timings
Sharp LL-191A — Relevant signal timings diagram (page 25)
Fig. 17 · Relevant signal timings

No. Function 1 Red video signal input 2 Green video signal input 3 Blue video signal input 4 GND 5 GND 6 For red video signal GND 7 For green video signal GND 8 For blue video signal GND 9 +5V 10 GND 11 GND 12 DDC data 13 For Hsync signal input 14 For Vsync signal input 15 DDC clock

Power management The monitor is based on VESA DPMS (Display Power Management Signaling). To activate the monitor's power management function, both the video card and the computer must conform to the VESA DPMS standard.

- Recommended resolution is 1280 x 1024. - All are compliant only with non-interlaced. - Frequencies for Power Macintosh and the Sun

Ultra series are reference values. To connect, another adapter (commercially available) may be required. - If the monitor is receiving timing signals that are

DPMSDisplay Power Management Signalling
Sharp LL-191A — Relevant signal timings diagram (page 25)
Fig. 18 · Relevant signal timings

not compatible, [OUT OF TIMING] will appear. Follow your computer's instruction manual to set the timing so that it is compatible with the monitor. - If the monitor is not receiving any signal (synch

signal), [NO SIGNAL] will appear.

DDC (Plug & Play) This monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for carrying out Plug & Play functions on the monitor or computer. It transfers information such as degree of resolution between the monitor and computer. You can use this function if your computer is DDC compliant and if it is set so that it can detect the Plug & Play monitor. There are many varieties of DDC due to the differences between systems. This monitor works with DDC2B.

Page 26 of the Sharp LL-191A user manual — Installing set-up information and the ICC profile (For Windows)
Pagina 26 · clicca per ingrandire
Pagina 26

Installing set-up information and the ICC profile (For Windows)

Depending on the type of computer or OS, you may need to install the monitor set-up information on your system. If so, follow the steps below to install the monitor set-up information. (Depending on the type of computer or OS, command names and methods may differ. Please follow the computer's own operation manual while reading this.)

Installing monitor set-up information into Windows 98, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the CD-ROM drive is "D" drive.

If the "Add New Hardware Wizard" has appeared: 1. Load the accessory CD-ROM into the CD-ROM drive of the computer. 2. Click [Next]. 3. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next]. 4. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK]. 5. Confirm that the monitor details are selected, then click [Next], [Next], and [Finish]. If the "Add New Hardware Wizard" appears, repeat the installation commands beginning from 2 above.

About the ICC profile An ICC (International Color Consortium) profile is a file that describes the color reproduction characteristics of the LCD monitor. Using an application compatible with an ICC profile, highly accurate color reproduction can be realized. - Windows 98/2000/Me/XP all use the ICC profile. - When installing Windows 98/2000/Me/XP set-up

information (described below), the ICC profile is also installed. If you would like to install the ICC profile only, please refer to Installing the ICC profile on page 28. - When using the ICC profile, set as follows:

- [DISPLAY MODE][STD] or [OFFICE] - [WHITE BALANCE]: [STD] - [GAMMA]: [0]

If the "Add New Hardware Wizard" has not appeared: 1. Load the accessory CD-ROM into the CD-ROM drive of the computer. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings], [Advanced] and [Monitor]. 5. In [Options], check [Automatically detect Plug & Play monitors] and click on [Change]. 6. Click [Next]. 7. Click on [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next]. 8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK]. 9. Confirm that the monitor details are selected, then click [Next], [Next], and [Finish]. 10. Check that the monitor details are displayed, then click [Apply]. 11. Click [OK], and close the window.

Installing monitor set-up information into Windows 95. This explanation assumes that the CD-ROM drive is "D" drive.

1. Load the accessory CD-ROM into the CD-ROM drive of the computer. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings], [Advanced Properties], and [Monitor], then [Change]. 5. Click on [Have disk], confirm that [Copy manufacturer's files from:] is [D:] then click [OK]. 6. Confirm that the monitor details are selected, and click [OK]. 7. Check that the monitor details are displayed, then click [Apply]. 8. Click [OK], and close the window.

For Windows 98 · For Windows 95

Page 27 of the Sharp LL-191A user manual — Installing set-up information and the ICC profile (For Windows)
Pagina 27 · clicca per ingrandire
Pagina 27

Installing set-up information and the ICC profile (For Windows)

Installing monitor set-up information into Windows 2000, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the CD-ROM drive is "D" drive.

Installing monitor set-up information into Windows Me, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the CD-ROM drive is "D" drive.

1. Load the accessory CD-ROM into the CD-ROM drive of the computer. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings], [Advanced] and [Monitor]. 5. Click on [Properties], [Driver] and [Update Driver]. 6. When [Upgrade Device Driver Wizard] appears, click [Next]. 7. Check [Display a list of the known drivers for this device so that I can choose a specific driver] and click [Next]. 8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK]. 9. Select the monitor from the list displayed and click [Next]. 10. Click [Next], confirm that the monitor's name appears on the screen, and click [Finish]. If [The Digital Signature Not Found] appears, click [Yes]. 11. Click on [Close]. 12. Click [OK], and close the window.

If the "Add New Hardware Wizard" has appeared: 1. Load the accessory CD-ROM into the CD-ROM drive of the computer. 2. Check [Specify the location of the driver [Advanced]] and click [Next]. 3. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next]. 4. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK]. 5. Select the monitor details from the list, then click [Next], [Next], and [Finish]. If the "Add New Hardware Wizard" appears, repeat the installation commands beginning from 2 above.

If the "Add New Hardware Wizard" has not appeared: 1. Load the accessory CD-ROM into the CD-ROM drive of the computer. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings], [Advanced] and [Monitor]. 5. In [Options], check [Automatically detect Plug & Play monitors] and click on [Change]. 6. Check [Specify the location of the driver [Advanced]] and click [Next]. 7. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.] and click [Next]. 8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK]. 9. Select the monitor details, then click [Next], [Next], and [Finish]. 10.Check that the monitor details are displayed, then click [Apply]. 11.Click [OK], and close the window.

For Windows 2000 · For Windows Me

Page 28 of the Sharp LL-191A user manual — Installing set-up information and the ICC profile (For Windows)
Pagina 28 · clicca per ingrandire
Pagina 28

Installing set-up information and the ICC profile (For Windows)

Installing the ICC profile Installing the monitor's ICC profile. (If the set-up information has already been installed, so too has the profile, and there is no need to install it.) This explanation assumes that the CD-ROM drive is "D" drive.

Installing monitor set-up information into Windows XP, and setting the monitor's ICC profile as a predetermined value. This explanation assumes that the CD-ROM drive is "D" drive.

1. Load the accessory CD-ROM into the CD-ROM drive of the computer. 2. Click on the [Start] button. Choose [Control Panel]. 3. Switch to "Classic View". 4. Double click on [Display]. 5. Click on [Settings], [Advanced] and [Monitor]. 6. Click on [Properties], [Driver] and [Update Driver]. 7. When [Hardware Update Wizard] appears, check [Install from a list or specific location [Advanced]] and click [Next]. 8. Check [Don't search. I will choose the driver to install.] and click [Next]. 9. Click on [Have Disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK]. 10. Select the monitor from the list displayed and click [Next]. If [has not passed Windows Logo testing...] appears, click [Continue Anyway]. 11. Confirm that the monitor's name appears on the screen. 12. Click on [Finish]. 13. Click on [Close]. 14. Click [OK], and close the window.

1. Load the accessory CD-ROM into the CD-ROM drive of the computer. 2. Click on the [Start] button. From [Settings], choose [Control Panel]. 3. Double click on [Display]. 4. Click on [Settings] and [Advanced]. 5. Click on [General] and from [Compatibility] select [Apply the new display setting without restarting], then click on [Color Management]. 6. Click [Add], and select CD-ROM as the file location. 7. Choose the color profile that you would like to install, and click on [Add]. 8. Choose the profile and click on [Set As Default]. 9. Click [OK], and close the window.

- When using the ICC profile, set as follows:

- [DISPLAY MODE][STD] or [OFFICE] - [WHITE BALANCE]: [STD] - [GAMMA]: [0]

For Windows XP

Page 29 of the Sharp LL-191A user manual — Setting up the ColorSync profile
Pagina 29 · clicca per ingrandire
Pagina 29

Information about the ColorSync profile (For MacOS)

About the ColorSync profile ColorSync is Apple Computer's color management system and enables color reproduction characteristics to be realized when used with a compatible application. A ColorSync profile describes the color characteristics of the LCD monitor.

MacOS 8.5 or above. - When using the ColorSync profile, set as

follows- [DISPLAY MODE]: [STD] or [OFFICE] - [WHITE BALANCE]: [STD] - [GAMMA]: [0]

Setting up the ColorSync profile

Exchange installed in your system. - Depending on the type of computer or OS,

command names and methods may differ. Please follow the computer's own operation manual while reading this.

1.Load the accessory CD-ROM into the CD-ROM drive of the computer. 2. Copy the profile to be used from the CD-ROM to the ColorSync profile folder in the system folder. 3.Using the ColorSync on the control panel, choose the profile to be used.

Page 30 of the Sharp LL-191A user manual — CAUTION!
Pagina 30 · clicca per ingrandire
Pagina 30

Instructions for attaching a VESA-compliant arm

The following stand or arm can be attached to the monitor. - Stand (sold separately)

5.Attach the arm to the monitor with the four screws.

Sharp LL-191A — Instructions for attaching a VESA-compliant arm diagram (page 30)
Fig. 19 · Instructions for attaching a VESA-compliant arm
Model nameNL-S02-H (Ivory)

NL-S02-B (Black) - VESA-compatible arm (commercially available)

Compatible commercially available arms Attachments must satisfy the following. - Compatible with the VESA standard. - Have a gap of 100 mm x 100 mm between the

screw holes on the section to be attached. - Not be likely to fall off or break off after being

attached to the monitor.

How to attach the arm or stand - Be careful not to over bend the cable or add

screws with a length of 6 - 8 mm protruding from the surface to be attached. Using different screws could cause the monitor to fall off or to be internally damaged.

extension cords as this could lead to malfunction. - While following these instructions, please also

refer to the installation instructions in the operation manual included with the arm or stand.

Sharp LL-191A — Instructions for attaching a VESA-compliant arm diagram (page 30)
Fig. 20 · Instructions for attaching a VESA-compliant arm

CAUTION!

- Be careful not to get your fingers pinched

between the display and stand nor to let the stand drop. These could lead to injury.

Arm Part of monitor to which arm is attached

1.Remove the cables. 2.Spread out a soft cloth on a suitable horizontal surface. 3.Being careful not to damage the monitor, gently lay the monitor on it display-side down. 4.Remove the four screws and then remove the stand from the monitor.

Sharp LL-191A — CAUTION! diagram (page 30)
Fig. 21

monitor. Once having removed the stand, never attempt to attach it to another device. - Once having removed the screws, store them

together with the stand and if the stand is ever re-attached be sure to use the original screws. Using different screws could lead to a malfunction.

Page 31 of the Sharp LL-191A user manual — Instructions for attaching a VESA-compliant arm
Pagina 31 · clicca per ingrandire
Pagina 31
Page 31 of the Sharp LL-191A user manual — Instructions for attaching a VESA-compliant arm
Page 32 of the Sharp LL-191A user manual — 根据电脑或电脑操作系统的不同型号规格,有可能需 要在电脑内安装设置信息。如果属于这种情况,那么 请按照如下步骤来安装显示器设置信息。(由于电脑 或电脑操作系统的型号规格不同,操作命令的名称和 方法也可能有所不同。在阅读本操作说明时,请参照 电脑本身的使用说明书。)
Pagina 32 · clicca per ingrandire
Pagina 32

安装设置信息和 ICC 文档(用于“ Windows ”)

根据电脑或电脑操作系统的不同型号规格,有可能需 要在电脑内安装设置信息。如果属于这种情况,那么 请按照如下步骤来安装显示器设置信息。(由于电脑 或电脑操作系统的型号规格不同,操作命令的名称和 方法也可能有所不同。在阅读本操作说明时,请参照 电脑本身的使用说明书。)

对于“Windows 98”

把显示器设置信息安装到“Windows 98”,把显示器 的ICC文档设置为预先确定的值。 在下述安装说明中,所用的菜单名称指的是英文版的 “Windows”中的菜单名称。请把这些名称作为安装 时的参考指南。 在本说明中,假定光盘驱动器是“D”驱动器。

关于ICC文档 ICC(国际色彩协会)文档是一个描述液晶显示器色彩 再生特性的文件。使用适合ICC文档的显示器可以获 得高精度的色彩再生。 - “Windows 98”、“Windows Me”、“Windows

如果已经显示出了“Add New Hardware Wizard” (添加新硬件向导):

1. 将附送的光盘装入电脑的“ D ”驱动器。 2. 单击[ Next ](下一步)。 3. 选择[ Display a list of all the drivers in a specific location, so you can select the driver you want. ](显示指定位置的全部驱动程序清单,这 样就能选择所需的驱动程序。),然后单击 [ Next ] (下一步)。 4. 当显示出[ Models ](型号 ) 时,单击[ Have disk ](搜索软盘驱动器),确认[ Copy manufacturer ’ s files from: ] (复制制造商的文件 从:)[ D: ],然后单击[ OK ] (确定)。 5. 确认已经选择了显示器的详细信息,然后单击 [ Next ] (下一步)、[ Next ](下一步),然后 [ Finish ] (完成)。如果显示出“ Add New Hardware Wizard ”(添加新硬件向导),那么请 从上述第 2 步开始重复进行安装命令操作。

2000”、“Windows XP”都使用ICC文档。 - 在安装“Windows 98”、“Windows Me”、

“Windows 2000”、“Windows XP”的设置信息 (如下所述)时,就会把ICC文档也安装进去。如 果只想安装ICC文档,那么请参阅第138页的“安装 ICC文档”。 - 使用ICC文档时,请如下设置∶

- [DISPLAY MODE](显示模式)∶[STD](标准)或

[OFFICE](省电) - [WHITE BALANCE](白色平衡)∶[STD](标准) - [GAMMA](灰度)∶[0]

对于“Windows 95”

把显示器设置信息安装到“Windows 95”。 在下述安装说明中,所用的菜单名称指的是英文版的 “Windows”中的菜单名称。请把这些名称作为安装 时的参考指南。 在本说明中,假定光盘驱动器是“D”驱动器。

如果没有显示出“Add New Hardware Wizard” (添加新硬件向导):

1. 将附送的光盘装入电脑的“D”驱动器。 2. 单击[Start](开始)按钮。从[Settings](设置) 菜单上选择[Control Panel] (控制面板)。 3. 双击[Display](显示)。 4. 单击[Settings] (设置)、[Advanced] (高级), 然后[Monitor](显示器)。 5. 在[Options] (选项)中,选择[Automatically detect Plug & Play monitors](自动检测即插即 用显示器),然后单击[Change] (更改)。 6. 单击[Next](下一步)。 7. 单击[Display a list of all the drivers in a specific location, so you can select the driver you want.](显示指定位置的全部驱动程序清单,这 样就能选择所需的驱动程序。),然后单击 [Next] (下一步)。 8. 当显示出[Models](型号)时,单击[Have disk](搜索软盘驱动器),确认[Copy manufacturer’s files from:] (复制制造商的文件 从:)[D:],然后单击[OK] (确定)。 9. 确认已经选择了显示器的详细信息,然后单击 [Next] (下一步)、[Next](下一步),然后 [Finish] (完成)。 10. 检查确认显示器的详细信息已经显示出来,然后 单击[Apply] (应用)。 11. 单击[OK](确定),关闭显示窗。

1. 将附送的光盘装入电脑的“ D ”驱动器。 2. 单击[ Start ](开始)按钮。从[ Settings ](设置) 菜单上选择[ Control Panel ](控制面板)。 3. 双击[ Display ](显示)。 4. 单击[ Settings ](设置)、[ Advanced Properties ](高级属性)、[ Monitor ](显示器), 然后[ Change ](更改)。 5. 单击[ Have disk ](搜索软盘驱动器),确认 [ Copy manufacturer ’ s files from: ](复制制造商 的文件从:)[ D: ],然后单击[ OK ](确定)。 6. 确认已经选择了显示器的详细信息,然后单击 [ OK ](确定)。 7. 检查确认显示器的详细信息已经显示出来,然后 单击[ Apply ](应用)。 8. 单击[ OK ](确定),关闭显示窗。
Page 33 of the Sharp LL-191A user manual — 汉语
Pagina 33 · clicca per ingrandire
Pagina 33

安装设置信息和 ICC 文档(用于“ Windows ”)

对于“Windows 2000”

对于“Windows Me”

把显示器设置信息安装到“Windows 2000”, 把显示器的ICC文档设置为预先确定的值。 在下述安装说明中,所用的菜单名称指的是英文版的 “Windows”中的菜单名称。请把这些名称作为安装 时的参考指南。 在本说明中,假定光盘驱动器是“D”驱动器。

把显示器设置信息安装到“Windows Me”,把显示器 的ICC文档设置为预先确定的值。 在下述安装说明中,所用的菜单名称指的是英文版的 “Windows”中的菜单名称。请把这些名称作为安装 时的参考指南。 在本说明中,假定光盘驱动器是“D”驱动器。

1. 将附送的光盘装入电脑的“D”驱动器。 2. 单击[Start](开始)按钮。从[Settings](设置) 菜单上选择[Control Panel](控制面板)。 3. 双击[Display](显示)。 4. 单击[Settings](设置)、[Advanced](高级), 然后[Monitor](显示器)。 5. 单击[Properties](属性)、[Driver](驱动程 序),然后[Update Driver](更新驱动程序)。 6. 当[Upgrade Device Driver Wizard](更新设备驱 动程序向导)显示出来时,单击[Next](下一 步)。 7. 选择[Display a list of the known drivers for this device so that I can choose a specific driver] (显示对于该设备的已知驱动程序清单,这样就 能选择一个指定的驱动程序),然后单击[Next] (下一步)。 8. 当显示出[Models](型号)时,单击[Have disk](搜索软盘驱动器),确认[Copy manufacturer’s files from:](复制制造商的文件 从:)[D:],然后单击[OK](确定)。 9. 从所显示的清单上选择显示器,然后单击 [Next](下一步)。 10. 单击[Next](下一步),确认显示器的名称出现在 屏幕上,然后单击[Finish](完成)。如果显示出 [The Digital Signature Not Found](没有找到 数字签名),请单击[Yes](是)。 11. 单击[Close](关闭)。 12. 单击[OK](确定),关闭显示窗。

如果已经显示出了“Add New Hardware Wizard” (添加新硬件向导):

1. 将附送的光盘装入电脑的“D”驱动器。 2. 选择[Specify the location of the driver [Advanced]](指定驱动程序的所在位置[高 级]),然后单击[Next](下一步)。 3. 选择[Display a list of all the drivers in a specific location, so you can select the driver you want.](显示指定位置的全部驱动程序清单,这 样就能选择所需的驱动程序。),然后单击 [Next] (下一步)。 4. 当显示出[Models](型号)时,单击[Have disk](搜索软盘驱动器),确认[Copy manufacturer’s files from:] (复制制造商的文件 从:)[D:],然后单击[OK] (确定)。 5. 从清单上选择显示器的详细信息,然后单击 [Next] (下一步)、[Next](下一步),然后 [Finish](完成)。如果显示出“Add New Hardware Wizard”(添加新硬件向导),那么请 从上述第2步开始重复进行安装命令操作。

如果没有显示出“Add New Hardware Wizard” (添加新硬件向导):

1. 将附送的光盘装入电脑的“D”驱动器。 2. 单击[Start](开始)按钮。从[Settings](设置) 菜单上选择[Control Panel] (控制面板)。 3. 双击[Display](显示)。 4. 单击[Settings] (设置)、[Advanced] (高级), 然后[Monitor](显示器)。 5. 在[Options] (选项)中,选择[Automatically detect Plug & Play monitors](自动检测即插即 用显示器),然后单击[Change] (更改)。 6. 选择[Specify the location of the driver [Advanced]](指定驱动程序的所在位置[高 级]),然后单击[Next] (下一步)。 7. 选择[Display a list of all the drivers in a specific location, so you can select the driver you want.] (显示指定位置的全部驱动程序清单,这样就能选 择所需的驱动程序。),然后单击[Next](下一步)。 8. 当显示出[Models](型号)时,单击[Have disk](搜索软盘驱动器),确认[Copy manufacturer’s files from:] (复制制造商的文件 从:)[D:],然后单击[OK] (确定)。 9. 选择显示器的详细信息,然后单击[Next] (下一 步)、[Next](下一步),然后[Finish](完成)。 10. 检查确认显示器的详细信息已经显示出来,然后 单击[Apply] (应用)。 11. 单击[OK](确定),关闭显示窗。

汉语

Page 34 of the Sharp LL-191A user manual — - 使用 ICC 文档时,请如下设置∶
Pagina 34 · clicca per ingrandire
Pagina 34

安装设置信息和 ICC 文档(用于“ Windows ”)

对于“Windows XP”

安装 ICC 文档

把显示器设置信息安装到“Windows XP”,把显示器 的ICC文档设置为预先确定的值。 在下述安装说明中,所用的菜单名称指的是英文版的 “Windows”中的菜单名称。请把这些名称作为安装 时的参考指南。 在本说明中,假定光盘驱动器是“D”驱动器。

安装显示器的ICC文档。(如果已经安装了设置信息, 那么也就已经安装了ICC文档,不需要再行安装 了。) 在下述安装说明中,所用的菜单名称指的是英文版的 “Windows”中的菜单名称。请把这些名称作为安装 时的参考指南。 在本说明中,假定光盘驱动器是“D”驱动器。

1. 将附送的光盘装入电脑的“D”驱动器。 2. 单击[Start](开始)按钮。选择[Control Panel] (控制面板)。 3. 切换到“Classic View(经典视图)”。 4. 双击[Display](显示)。 5. 单击[Settings](设置)、[Advanced](高级)、 然后[Monitor](显示器)。 6. 单击[Properties](属性)、[Driver](驱动程 序)、然后[Update Driver](更新驱动程序)。 7. 当显示出[Hardware Update Wizard](硬件更新 向导)时,选择[Install from a list or specific location[Advanced]](从列表或指定位置安装 [高级]),然后单击[Next](下一步)。 8. 选择[Don’t search, I will choose the drive to install.](不要搜索,自己选择驱动程序安装。), 然后单击[Next](下一步)。 9. 单击[Have Disk](搜索软盘驱动器),确认 [Copy manufacturer’s files from:](复制制造商 的文件从:)[D:],然后单击[OK](确定)。 10. 从所显示的清单上选择所需的显示器,然后单击 [Next](下一步)。如果显示出[has not passed Windows Logo testing ...](没有通过视窗商标测 试⋯),那么请单击[Continue Anyway](仍然继 续)。 11. 确认该显示器的名称已在屏幕上显示出来。 12. 单击[Finish](完成)。 13. 单击[Close](关闭)。 14. 单击[OK](确定),关闭显示窗。

1. 将附送的光盘装入电脑的“ D ”驱动器。 2. 单击[ Start ](开始)按钮。从[ Settings ](设置) 菜单上选择[ Control Panel ] (控制面板)。 3. 双击[ Display ](显示)。 4. 单击[ Settings ](设置),然后单击[ Advanced ] (高级)。 5. 单击[ General ](常规),从[ Compatibility ](兼容 性)选择[ Apply the new display setting without restarting ](应用新的显示设置而不重新启动), 然后单击[ Color Management ](色彩管理)。 6. 单击 [Add ] (添加),选择光盘作为文件位置。 7. 选择想要安装的彩色文档,然后单击[ Add ](添 加)。 8. 选择文档,然后单击[ Set As Default ](设置为默 认)。 9. 单击[ OK ](确定),关闭显示窗。

- 使用 ICC 文档时,请如下设置∶

- [DISPLAY MODE](显示模式)∶[STD](标准)或

[OFFICE](省电) - [WHITE BALANCE](白色平衡)∶[STD](标准) - [GAMMA](灰度)∶[0]

Fonti

Riferimenti e link

Pagine di riferimento in questo manuale: produttore, supporto e download.

Fai una domanda su Sharp LL-191A

I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nessuna domanda ancora per il dispositivo Sharp LL-191A

Invia la prima domanda: risponderanno altri possessori o il nostro team.

Documento originale

Sharp LL-191A manuale in PDF

148 pagine·4.7 MB·Monitor per computer·PDF
Clicca su qualsiasi pagina in alto per aprirla qui
Pagina 1 / …
100%
Caricamento pagine…