Manuale d’uso / di manutenzione del prodotto 831.159460 del fabbricante Sears
Vai alla pagina of 28
USER'S MANU AL Model No. 831.159460 Serial No. CA UTION Read all precautions and instruc- tions in this manual bef ore using this equipment. Save this manual f or future reference. P A TENT PENDING The serial number can be found in the location shown belo w .
2 T ABLE OF CONTENTS FULL 90 D A Y W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPOR T ANT PRECA UTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature bef ore using the home gym system. 2. It is the responsibility of the owner to ensure that all users of the home gym system are adequately inf ormed of all precautions.
4 ASSEMBLED DIMENSIONS: Height: 74 in. Width: 40 in. Length: 58 in. F oot Plate Low Pulle y Station High Pulley Station Lat Bar Leg Le ver V er tical Knee Raise (VKR) Arm Butterfly Arms Curl P ad Curl.
1 High Side of Brac ket 51 5 14 1 3 Slotted Hole 3 8 56 11 3 1 4 27 51 1. Before beginning assemb ly , be sure that y ou have read and under stand the infor- mation in the bo x above. Press a 2” Square Outer Cap (51) onto each end of the Stabilizer (5).
2. Slide the F ront Upr ight (42) onto the 5/16” x 2 1/2” Carriage Bolts (1) in the Base (4). Hand tighten a 5/16” Nylon Lockn ut (3) onto each Carriage Bolt. Do not tighten the Nylon Lockn uts yet. Press a 1” Square Inner Cap (65) into the F ront Upr ight (42).
5. Press the Weight T ube Bumper (64) into the end of the Weight T ube (63). Inser t the W eight T ube into the stack of W eights (25). Be sure that the pins on the W eight T ube are sitting in the pin groo ves in the top W eight. Lubricate the insides of the holes in the T op W eight (76).
ARM ASSEMBL Y 8. W et the handle of one Press Arm (46) with soap y water . Slide a Hand Grip (31) onto the handle. Press a 1” Round Inner Cap (49) into the other end of the handle.
9 CABLE ASSEMBL Y 11. During steps 11 through 27, refer to the CABLE DIA GRAM on page 22 of this manual to v erify proper cable routing. Before begin- ning this section, identify the Long Cable (23), the Medium Cable (58), and the Short Cable (35) by comparing the lengths and ends of the cables .
18 15 23 12 20 15 66 68 50 48 6 7 16 17 CABLE ASSEMBL Y 10 15. Route the Long Cable (23) around the “V”- Pulley (6) on the Right Arm (48). Be sure that the Cable is in the gr oove of the “V”- Pulley and that the Long Cable T rap (50) is turned to hold the Cable in place.
19. Assembly steps 19 thr ough 21 show how to complete the assembl y of several pre- attached parts. The 5/8” x 9/16” Spacer (73) has been pre- attached on the outside of the 3 1/2” Low Pulley (92) f or shipping pur poses. Remov e the 3/8” Nylon Lockn ut (21), the Spacer , and the Pulley from the 3/8” x 3 3/4” Bolt (71).
25 22 23 24 22. Locate the Medium Cable (58). Route the Medium Cable (58) under the 3 1/2” Low Pulley (92) attached to the lo wer hole in the Press F rame (17). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame and that the Cable is between the Pulley and the cr ossbar on the Press Frame.
26. Attach the end of the Medium Cable (58) to the Long “U”-Brac ket (57) with a 1/4” Nylon Lockn ut (2) and a 1/4” Flat Washer (10). Do not completely tighten the Nylon Loc knut. It should be threaded onto the end of the Cable so onl y a couple of threads are showing abo ve the Locknut, as shown in the inset drawing.
29. Press a 1 1/2” Square Inner Cap (32) into the Seat F rame (36). Inser t the 1/4” x 2” Carr iage Bolt (38) into the center hole in the Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4” x 1/2” Screws (18). Inser t the 1/4” x 2” Carr iage Bolt (38) into the indicated hole in the Seat F rame (36).
33. Press 3/4” Round Inner Caps (34) into the ends of both 12 1/2” P ad T ubes (28). Inser t one 12 1/2” Pad T ube (28) into the Seat F rame (36). Slide a 5 1/2” Pad (30) onto each end of the P ad T ube. Inser t the other 12 1/2” Pad T ube (28) into the Leg Le ver (29).
36. Press 1 1/2” Square Inner Caps (32) into the ends of the Left VKR Ar m (79) and the Right VKR Ar m (80). Press 1” Round Inner Caps (49) into the ends of the handles on the Left VKR Ar m and the Right VKR Arm.
17 38. Remov e the decals from the decal sheet (not shown) and apply them to the home gym system in the loca- tions shown in the illustration belo w . 38 39. Make sure that all parts have been properly tightened. The use of the remaining par ts will be explained in ADJUSTMENT , beginning on page 18 of this manual.
54 39 53 52 23 25 26 54 39 52 53 58 53 CHANGING THE WEIGHT SETTING T o change the weight setting of the weight stac k, inser t the W eight Pin (26) under the desired Weight (25). Be sure to inser t the W eight Pin until the bent end of the Weight Pin is touching the Weights , and turn the bent end downward.
19 A TT A CHING AND REMO VING THE SEA T Set the brac ket on the Seat F rame (36) on the indicat- ed pins on the F ront Upr ight (42). Attach the Seat F rame to the F ront Upr ight with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40). F or some e x ercises, the Seat F rame (36) must be re- mov ed.
20 WEIGHT RESIST ANCE CHART This char t shows the appro ximate weight resistance at each e xercise station. “T op” refers to the 6.5 lb . top weight. The other numbers refer to the 12.5 lb . weight plates. The butterfly arm resistance listed is the resistance f or each butterfly arm.
21 TR OUBLE-SHOO TING AND MAINTENANCE Inspect and tighten all par ts each time you use the home gym system. Replace any worn par ts immediately . The home gym system can be cleaned using a damp cloth and mild non-abrasiv e detergent. Do not use solvents .
22 CABLE DIA GRAM The diagram belo w shows the proper routing of the Shor t Cable (35), the Medium Cable (58), and the Long Cable (23). Use the diagram to be sure that the cab les and the cable tr aps hav e been assembled correctly . If the cables ha ve not been correctly routed, the home gym system will not function properly and damage may occur .
1 1/2" Square Inner Cap (32)–5 1 3/4" Square Inner Cap (44)–6 2" Square Inner Cap (27)–2 2" Square Outer Cap (51)–2 1" x 7/8" Plastic Bushing (75)–2 1" Squ.
5/16" Nylon Locknut (3)–23 1/4" Flat W asher (10)–12 5/16" Flat W asher (8)–8 3/8" Flat W asher (9)–4 1/4" x 2 1/2" Screw (43)–4 3/8" Nylon Locknut (21)–.
1" Round Inner Cap (49)–10 1" Round Cover Cap (70)–2 3/4" Round Inner Cap (34)–4 3/8" x 3 1/2" Bolt (16)–1 5/16" x 5" Bolt (68)–1 3/8" x 3 3/4" B.
P AR T LIST—Model No. 831.159460 R0696A Key Par t No. No. Qty . Description 1 100291 3 5/16” x 2 1/2” Carriage Bolt 2 012139 3 1/4” Nylon Lockn ut 3 012056 23 5/16” Nylon Locknut 4 127049 1 .
23 11 11 8 8 55 27 12 15 44 15 71 23 21 44 21 3 61 60 3 3 5 51 14 19 26 51 25 64 63 3 76 72 9 21 3 3 4 1 27 65 15 71 41 10 43 3 21 6 50 7 42 7 50 6 21 69 70 69 70 47 48 44 45 44 45 52 53 39 49 62 2 10.
P ar t No . 127242 R0696A Printed in Canada © 1996 Sears, Roebuc k and Co. Model No. 831.159460 QUESTIONS? If you find that: • y ou need help assembling or operating the LIFESTYLER ® SYSTEM 200 .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sears 831.159460 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sears 831.159460 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sears 831.159460 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sears 831.159460 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sears 831.159460, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sears 831.159460.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sears 831.159460. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sears 831.159460 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
