Manuale d’uso / di manutenzione del prodotto 390.252158 del fabbricante Sears
Vai alla pagina of 16
SEARS OWNER'S MANUAL MODEL NO. 390.252158 CAUTION: Read and Follow All Safety Rules and Operating Instructions Before First Use of This Product. Save This Manual For Future Reference.
CONTENTS INTRODUCTION/WARRANTY .......................................... 2 PUMP PERFORMANCE ....................................................... 3 MAJOR COMPONENTS ...................................................... 3 INSTALLATION .............
SAFETY INSTRUCTIONS (Continued) 6. Disconnect electrical power source before installing or working on pump. 7. Ground pump with a ground wire run from grounding lug on motor to a grounded lead in the service panel. 8. Line voltage and frequency of electrical power supply must agree with motor nameplate.
INSTALLATION INSTALLATION Piping in the Well The Shallow Well Water System can be installed on a dug well, drilled well or with a driven point. In a dug or cased well, a foot valve and strainer should be installed for easy priming.
INSTALLATION 1-1/4" 1-1/2" 2" Up to 25 Ft. 25 to 50 Ft. 50 to 200 Ft. Discharge Pipe Sizes When the pump is some distance from the house or point of water use, the discharge pipe size should be increased to reduce pressure losses caused by friction.
ELECTRICAL Disconnect power before working on pump, motor, pressure switch, or wiring. Your Motor Terminal Board (under the motor end cover) if line voltage is 230 Volts or if you have a single voltage and Pressure Switch look like one of those shown below, motor: Connect power supply as shown for your type of Convert to 115 Volts as shown.
OPERATION Priming the Pump NOTICE: To properly prime the pump, install a pipe tee in the discharge piping (see Figure 1, Page 4). To prevent damage to internal-parts, do not start motor until pump has been filled with water. To prime pump: 1. Remove priming plug (Purchase separately; Figure 1, Page 4).
MAINTENANCE NOTICE: DO not overtighten; you may twist studs off of tank. If you have a torque wrench, tighten to 85 inch- pounds torque. 18. Stand tank on feet and reconnect piping. 19. Recharge tank to proper air pressure (see Page 5). 20. Reconnect hoses and pressure switch tube; prime pump (see Page 6).
MAINTENANCE 4. Place back half of pump on flat surface and tap out ce- ramic seat. See Figure 6. I. Screw impeller on shaft (clockwise) while holding shaft with 7/16" open end wrench on shaft flats. This will automatically locate seal in place. See Figure 8.
HELPFUL HINTS How to Handle a Gaseous Well In some areas well water contains gases which must be al- lowed to escape before the water is used. This can be done as shown in Figure 9. A good way of delivering gas-free water is to suspend a pipe, closed at the bottom and open at the top, surrounding the suction pipe.
TROUBLESHOOTING GUIDE TROUBLE POSSIBLE CAUSES REMEDIES Motor will not run 1. Disconnect switch is off 1. Be sure switch is on 2. Fuse is blown 2. Replace fuse 3. Starting switch is defective 3. Replace starting switch 4, Wires at motor are loose, 4. Refer to instructions on wiring disconnected, or wired incorrectly *5.
REPAIR PARTS Pump Only - Model 390.252158 30 29 28 I 2 3 4 11 23 8 9 16 17 24 19 1c lO 2O 22 21 To Order Parts in the U.S.A., Call Sears Product Service, 1-800-366-7278 .
REPAIR PARTS Key Model 390.252158 Part No. 1/2 HP Description 1"* J218-953C 1A 1B 1C 1D 1E 2 3* 4 5 6 7 8 9 10 11 12 13 14 15 16 16 17 18 19 20 2:1" 22 23 24 25 26* 26A 27 28 29 3O U18-1103 .
REPAIR PARTS Tank Only - Model 390.252158 7 REPAIR PARTS Model 390.252158 Key 1/2 HP Qty. No. Part Number Used 1 29135 1 2 3 4 5 6 7 U20-13 U212-160 t U31-446P U36-2.
15.
SEARS OWNER'S MANUAL Model No. 390.252158 The model number of your Shallow Well Water Systemwill be found on the pump body. When requesting service or ordering parts, always give the following in.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sears 390.252158 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sears 390.252158 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sears 390.252158 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sears 390.252158 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sears 390.252158, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sears 390.252158.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sears 390.252158. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sears 390.252158 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
