Manuale d’uso / di manutenzione del prodotto 2004 Ion del fabbricante Saturn
Vai alla pagina of 380
Seats and Restraint Systems ........................... 1 - 1 Front Seats ............................................... 1 - 2 Rear Seats ............................................... 1 - 7 Safety Belts .............................................
SATURN and the SATURN Emblem are registered trademarks of Saturn Corporation and the name ION is a trademark of Saturn Corporation. GENERAL MOTORS and GM are registered trademarks of General Motors Corportation. This manual includes the latest information at the time it was printed.
Safety Warnings and Symbols You will find a number of safety cautions in this book. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning. { CAUTION: These mean there is something that could hurt you or other people.
Vehicle Damage Warnings Also, in this manual you will find these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage your vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
These are some examples of symbols that may be found on the vehicle: v.
✍ NOTES vi.
Front Seats ..................................................... .1-2 Manual Seats ............................................... .1-2 Driver Seat Height Adjuster ............................. .1-3 Reclining Seatbacks ...............................
Front Seats Manual Seats { CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Driver Seat Height Adjuster If your vehicle has this feature, the driver’s seat height adjuster is located on the left side of the seat. To raise the seat, ratchet the lever upward until the seat is at the desired height. To lower the seat, ratchet the lever downward until the seat is at the desired height.
But don’t have a seatback reclined if your vehicle is moving. { CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this. The shoulder belt can not do its job because it will not be against your body.
Head Restraints Press the button on the side of the head restraint to adjust it. Adjust your head restraint so that the top of the restraint is closest to the top of your head.
Passenger Folding Seatback The front passenger’s seatback may fold flat. To fold the seatback, do the following: 1. Lift the bar under the seat to unlock it. 2. Slide the seat as far back as it will go and release the bar. Try to move the seat with your body to make sure it is locked into place.
Rear Seats Split Folding Rear Seat You can fold either side of the rear seatback down for more cargo space. To lower the rear seatback, follow these steps: 1. If you have a sedan and it is equipped with this feature, open the trunk and pull one or both of the small handles located in the center of the trunk.
To raise the rear seatback, lift it up and rearward until you hear a click. Push and pull on the seat back to be sure it is locked into place. { CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there.
{ CAUTION: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Take the simplest vehicle. Suppose it’s just a seat on wheels. Put someone on it.
Get it up to speed. Then stop the vehicle. The rider doesn’t stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield.
or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces.
Questions and Answers About Safety Belts Q: Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? A: You could be – whether you’re wearing a safety belt or not. But you can unbuckle a safety belt, even if you’re upside down.
How to Wear Safety Belts Properly This part is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see Older Children on page 1-29 or Infants and Young Children on page 1-32 .
Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 1-28 . Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Shoulder Belt Height Adjuster (Sedan) Before you begin to drive, move the shoulder belt adjuster to the height that is right for you. Adjust the height so that the shoulder portion of the belt is centered on your shoulder. The belt should be away from your face and neck, but not falling off your shoulder.
Q: What’s wrong with this? A: The shoulder belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Q: What’s wrong with this? A: The belt is buckled in the wrong place. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Q: What’s wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Q: What’s wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your retailer to fix it.
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle. Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women.
Right Front Passenger Position To learn how to wear the right front passenger’s safety belt properly, see Driver Position on page 1-14 . The right front passenger’s safety belt works the same way as the driver’s safety belt — except for one thing.
Lap-Shoulder Belt All rear seating positions have lap-shoulder belts. Here is how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
3. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder part. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash this applies force to the strong pelvic bones.
The safety belt locks if there is a sudden stop or a crash, or if you pull the belt very quickly out of the retractor. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Rear Safety Belt Comfort Guides for Children and Small Adults Rear shoulder belt comfort guides will provide added safety belt comfort for older children who have outgrown booster seats and for small adults. When installed on a shoulder belt, the comfort guide better positions the belt away from the neck and head.
3. Return the rear seatback to its upright position and make sure it is latched into place. 4. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edges of the belt into the slots of the guide.
6. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-22 . Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides.
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. Q: What is the proper way to wear safety belts? A: If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
{ CAUTION: Never do this. Here two children are wearing the same belt. The belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured.
{ CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen.
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints.
CAUTION: (Continued) hold it. For example, in a crash at only 25 mph (40 km/h), a 12-lb. (5.5 kg) baby will suddenly become a 240-lb. (110 kg) force on a person’s arms. A baby should be secured in an appropriate restraint. { CAUTION: Children who are up against, or very close to, any air bag when it inflates can be seriously injured or killed.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types.
{ CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint.
A booster seat (F-G) is a child restraint designed to improve the fit of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a five-point harness. A booster seat can also help a child to see out the window.
When choosing a child restraint, be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor vehicle safety standards. Then follow the instructions for the restraint. You may find these instructions on the restraint itself or in a booklet, or both.
CAUTION: (Continued) If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat. Wherever you install it, be sure to secure the child restraint properly.
In Canada, the law requires that forward-facing child restraints have a top strap, and that the strap be anchored. In the United States, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored. Anchor the top strap to an anchor point specified in Top Strap Anchor Location on page 1-41 .
Top Strap Anchor Location Your vehicle has top strap anchors installed for the rear seating positions only. Do not secure a child restraint with a top strap in the right front passenger’s position i.
Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You will find anchors for all three rear seating positions on the sedan and both rear seat outside passenger positions on the coupe. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts.
A. Lower Anchorage B. Lower Anchorage In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback at each lower anchor position.
Securing a Child Restraint Designed for the LATCH System 1. Find the LATCH anchorages for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. See Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-42 .
If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say. 1. Put the restraint on the seat.
4. Pull the rest of shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety belt will move freely again and be ready to work for an adult or larger child passenger.
A rear seat is a safer place to secure a forward-facing child restraint. If you need to secure a forward-facing child restraint in the right front seat, you will be using the lap-shoulder belt to secure the child restraint. Be sure to follow the instructions that came with the child restraint.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Air Bag Systems This part explains the air bag systems. Your vehicle has a frontal air bag for the driver and another frontal air bag for the right front passenger.
CAUTION: (Continued) The roof-mounted side impact air bags are designed to inflate only in moderate to severe crashes where something hits the side of your vehicle.
There is an air bag readiness light on the instrument panel cluster, which shows the air bag symbol. The system checks the air bag electrical system for malfunctions. The light tells you if there is an electrical problem. See Air Bag Readiness Light on page 3-30 for more information.
The right front passenger’s frontal air bag is in the instrument panel on the passenger’s side. If your vehicle has a side impact air bag for the driver and the person seated directly behind the driver, it is in the ceiling above the side windows.
If your vehicle has a side impact air bag for the right front passenger and the person seated directly behind that passenger, it is in the ceiling above the side windows.
When Should an Air Bag Inflate? The driver’s and right front passenger’s frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes. But they are designed to inflate only if the impact speed is above the system’s designed “threshold level.
What Makes an Air Bag Inflate? In an impact of suff icient severity, the air bag sensing system detects that the vehicle is in a crash. For both frontal and side impact air bags, the sensing system triggers a release of gas from the inflator, which inflates the air bag.
{ CAUTION: When an air bag inflates, there is dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so.
Servicing Your Air Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There are air bag system parts in several places around your vehicle.
Restraint System Check Checking Your Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts.
If the LATCH system was being used during a more severe crash, you may need new LATCH system parts. If belts are cut or damaged, replace them. Collision damage also may mean you will need to have LATCH system, safety belt or seat parts repaired or replaced.
Keys .............................................................. .2-3 Remote Keyless Entry System ........................ .2-4 Remote Keyless Entry System Operation .......... .2-5 Doors and Locks ............................................ .2-9 Door Locks .
Mirrors .......................................................... .2-36 Manual Rearview Mirror ................................ .2-36 Manual Rearview Mirror with OnStar ® ............... .2-36 Automatic Dimming Rearview Mirror with OnStar ® , Compass and Temperature Display .
Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children.
You may be able to obtain a valet key from you retailer. The valet key only works in the doors and ignition. Notice: If you ever lock your keys in your vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys. Your key has a transponder in it that matches a decoder in your vehicle’s steering column.
At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: • Check the distance. You may be too far from your vehicle.
W (Unlock): Press this symbol on the remote keyless entry transmitter to unlock the driver’s door. This also disarms the theft-deterrent system. See “Theft-Deterrent System” following for information on disarming the theft-deterrent system. Press the button again to unlock the rest of the doors.
3. You must complete one of the following within three seconds to change the mode. • To select the active arming mode, press the lock button on the transmitter. • To select the passive arming mode, press the trunk release button on the transmitter.
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’s probably time to change the battery.
Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Power Door Locks From the inside of the vehicle, push the top of the switch to unlock the door. Press the bottom of the switch to lock all of the doors at once.
Rear Door Security Locks Your vehicle has rear door security locks that prevent passengers from opening the rear doors from the inside. The rear door security locks are located on the inside edge of each rear door. You must open the rear doors to access them.
Rear Doors (Coupe) Your vehicle has a driver’s and passenger’s side rear access door. To open the rear access doors, first you must open the driver’s or passenger’s door. Then use the handle located on the front edge of the rear door to open it.
Remote Trunk Release Press the remote trunk release button, located on the lower left side of the instrument panel, to release the trunk lid. Make sure the remote trunk release lockout feature is not activated.
Emergency Trunk Release Handle Notice: Using the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk may damage it. Use the emergency trunk release handle only to help you open the trunk lid. There is a glow-in-the-dark emergency trunk release handle located on the inside of the trunk lid of your vehicle.
Manual Windows On a vehicle with manual windows, use the window crank to open and close each window. Power Windows If your vehicle has power windows, switches located on the driver’s door armrest control each of the windows. In addition, each passenger’s door has a window switch that controls that door’s window.
Express-Down Window The driver’s window switch has an express-down feature. This switch is labeled AUTO. Tap the rear of the switch, and the driver’s window will open a small amount. If the rear of the switch is fully pressed, the window will go all the way down.
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Passlock ® Your vehicle is equipped with the Passlock ® theft-deterrent system.
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate “break-in.” But it will perform better in the long run if you follow these guidelines: • Do not drive at any one speed — fast or slow — for the first 500 miles (805 km).
9 (LOCK): This position locks your steering column in a vehicle with a manual transmission. It is a theft-deterrent feature. You will only be able to remove your key when the ignition is turned to LOCK. If you have an automatic transaxle, the ignition switch can’t be turned to LOCK unless the shift lever is in PARK (P).
Starting Your Engine Automatic Transaxle Move your shift lever to PARK (P) or NEUTRAL (N). Your engine won’t start in any other position — that’s a safety feature. To restart when you’re already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle.
3. If your engine still won’t start (or starts but then stops), it could be flooded with too much gasoline. Try pushing your accelerator pedal all the way to the floor and holding it there as you hold the key in START for about three seconds.
Engine Coolant Heater If your vehicle has this feature, in very cold weather 0°F ( − 18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Automatic Transaxle Operation Five-Speed Automatic and VTi Variable If your vehicle is equipped with either the five-speed automatic transaxle or the VTi variable automatic transaxle, the shift lever is located on the console between the seats. There are several different positions for the automatic transaxle.
For vehicles with the VTi variable transaxle, if the TRANS COLD message is displayed in cold temperatures (below − 13°F ( − 25°C)) and the shift lever is moved out of PARK (P), the transaxle will not go into gear. Return the shift lever to PARK (P) and wait for the TRANS COLD message to turn off.
Notice: Shifting to a drive gear from NEUTRAL (N) while the vehicle is moving could damage the transaxle. Make sure the vehicle is stopped before shifting from NEUTRAL (N) into a drive gear. AUTOMATIC OVERDRIVE (D): This position is for normal driving with the automatic transaxle.
Shift Lock Release This vehicle is equipped with an electric shift lock release system. The shift lock release is designed to do the following: • Prevent the ignition key from being removed unless the shift lever is in PARK (P), and • Prevent movement of the shift lever out of PARK (P) unless the ignition is in a position other than LOCK.
3. Place your finger into the access hole and locate the plunger. 4. Press and hold the plunger toward the driver’s door while turning the ignition key to LOCK.
Manual Transaxle Operation Five-Speed This is your shift pattern. Here’s how to operate your transaxle: FIRST (1): Press the clutch pedal and shift into FIRST (1). Then, slowly let up on the clutch pedal as you press the accelerator pedal. You can shift into FIRST (1) when you’re going less than 20 mph (32 km/h).
Shift Speeds { CAUTION: If you skip a gear when you downshift, you could lose control of your vehicle. You could injure yourself or others. Don’t shift down more than one gear at a time when you downshift. Up-Shift Light If you have a manual transaxle, you may have an up-shift light.
Parking Brake The parking brake lever is located between the seats. To set the parking brake, hold the brake pedal down and pull up on the parking brake lever. If the ignition is on, the brake system warning light will come on. To release the parking brake, hold the brake pedal down.
Shifting Into Park (P) (Automatic Transaxle) { CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Leaving Your Vehicle With the Engine Running { CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire.
Shifting Out of Park (P) (Automatic Transaxle) Your vehicle has an automatic transaxle shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN. See Automatic Transaxle Operation on page 2-23 .
Parking Over Things That Burn { CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can not see or smell.
Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Mirrors Manual Rearview Mirror When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from the lamps behind you.
Automatic Dimming Rearview Mirror with OnStar ® , Compass and Temperature Display Your vehicle may have this feature. When on, an automatic dimming mirror automatically dims to the proper level to minimize glare from lights behind you after dark. The mirror also includes a dual display in the upper right corner of the mirror face.
Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror do the following: 1. Make sure the green indicator light, located to the left of the on/off button, is lit.
To adjust for compass variance do the following: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the on/of f button until a zone number appears in the display. The compass is now in zone mode. 3. Keep pressing the on/of f button until the desired zone number appears in the display.
Automatic Dimming Rearview Mirror with Compass and Temperature Display If your vehicle is equipped with an automatic dimming mirror it will automatically dim to the proper level to minimize glare from lights behind you after dark. The mirror also includes a display in the upper right corner of the mirror face.
To adjust for compass variance: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the COMP button for five seconds until a zone number appears in the display. 3. Press the COMP button on the bottom of the mirror until the new zone number appears in the display.
Outside Remote Control Mirror The outside rearview mirror should be adjusted so you can see a little of the side of your vehicle when you are sitting in a comfortable driving position. Adjust the driver’s outside mirror with the knob on the driver’s door.
OnStar ® System Your vehicle may have this feature. OnStar ® uses global positioning system (GPS) satellite technology, wireless communications, and state of the art call centers to provide you with a wide range of safety, security, information and convenience services.
Luxury and Leisure Plan • All Directions and Connections Plan services • Personal Concierge OnStar ® Personal Calling With OnStar ® Personal Calling, you have a safer way to stay connected while driving. It’s a hands-free wireless phone that’s integrated into your vehicle.
Roof Rack System If your vehicle has a roof rack, you can load things on top of your vehicle. Notice: Loading cargo on the luggage carrier that weighs more than 100 lbs.
✍ NOTES 2-46.
Instrument Panel Overview .............................. .3-4 Hazard Warning Flashers ............................... .3-6 Other Warning Devices .................................. .3-7 Horn ............................................................ .
Message Center ............................................ .3-41 Low Traction Message .................................. .3-42 Traction Off Message ................................... .3-42 Cruise Control Message ................................ .3-42 Transaxle Fluid Hot Message .
✍ NOTES 3-3.
Instrument Panel Overview 3-4.
The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-24 Outlet Adjustment. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-8 Turn Signal/Multifunction Lever. C.
Hazard Warning Flashers Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off. The hazard warning flasher button is located near the center of the instrument panel.
Other Warning Devices If you carry reflective triangles, you can set one up at the side of the road about 300 feet (100 m) behind your vehicle. Horn You can sound the horn by pressing the center of your steering wheel. Tilt Wheel Your vehicle may have a tilt wheel which allows you to adjust the steering wheel before you drive.
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane-Change Signals • Headlamps • Headlamp High/Low-Beam Changer • Flash-to-Pass Feature For additional information on the exterior lamps, see Exterior Lamps on page 3-15 .
As you signal a turn or a lane change, if the arrows flash rapidly, a signal bulb may be burned out and other drivers won’t see your turn signal. If a bulb is burned out, replace it to help avoid an accident.
Headlamps The exterior lamp control is located in the middle of the turn signal/multifunction lever. O (Exterior Lamp Control): Turn the control with this symbol on it to operate the exterior lamps.
Windshield Wiper Lever The lever on the right side of the steering column operates the windshield wipers. 7 (Mist): Pull the lever down and release it for a single wiping cycle. The lever will return to its original position. For more cycles, hold the lever down before releasing it.
Windshield Washer { CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. L (Washer Fluid): Pull the windshield wiper lever toward you to operate the windshield wipers.
With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). If you apply your brakes or the clutch, the cruise control will shut off.
Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But you don’t need to reset it. Once you’re going about 25 mph (40 km/h) or more, you can press the cruise control resume/accelerate button.
Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down.
When the DRL are on, your low-beam headlamps will be on at a reduced brightness. The taillamps, sidemarker and other lamps won’t be on. Your instrument panel won’t be lit up either. When you turn the exterior lamp band to the headlamp position, your low-beam headlamps will come on.
Fog Lamps If your vehicle has this feature, use your fog lamps for better visibility in foggy or misty conditions. The button for your fog lamps is located next to the instrument panel brightness control. Push the button to turn the fog lamps on. Push the button again to turn the fog lamps off.
Entry Lighting If the dome lamp is in the DOOR position, the lamps inside your vehicle will come on when any door is opened. In addition, the light will come on when the remote keyless entry unlock button is pressed. It will stay on for 20 seconds or until a door is opened.
Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on the accessory power outlet.
Climate Controls Climate Control System (Without Air Conditioning) With this system you can control the heating and ventilation for your vehicle. Operation To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets.
Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield and side windows.
Climate Control System (With Air Conditioning) With this system you can control the heating, cooling and ventilation for your vehicle. Operation To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets.
The air-conditioning compressor also comes on. Operation in this mode during periods of high humidity and cool outside temperatures may result in increased window fogging. If window fogging is experienced, select the defrost mode. # (Air Conditioning): Press this button to turn the air-conditioning system on or off.
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. The rear window defogger will only work when the ignition is in RUN. < (Rear): Press the button to turn the rear window defogger on or off. Be sure to clear as much snow from the rear window as possible.
Passenger Compartment Air Filter Passenger compartment air, both outside air and recirculated air, is routed through a passenger compartment filter. The filter removes certain particles from the air, including pollen and dust particles.
4. Open the passenger compartment air filter door by reaching through the opening in the back of the glove box and raising the tab until the door can be opened downward. 5. Remove the filter by sliding it out of the housing. When installing a new air filter make sure the AIR FLOW arrow is pointing downward.
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Instrument Panel Cluster Your instrument cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel you’ve used, and many other things you’ll need to know to drive safely and economically.
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer is located in your message center, and shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada).
Safety Belt Reminder Light When the key is turned to RUN or START, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds, then it will flash for several more.
{ CAUTION: If the air bag readiness light stays on after you start your vehicle, it means the air bag system may not be working properly. The air bags in your vehicle may not inflate in a crash, or they could even inflate without a crash.
Up-Shift Light Your vehicle may have up-shift light. When this light comes on, you should shift to the next higher gear if weather, road, and traff ic conditions allow you to. This light is located in your instrument panel cluster to the left of the speedometer.
When the ignition is on, the BRAKE light will come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. A chime will also sound if the parking brake is not fully released and the vehicle is moving. If it stays on after your parking brake is fully released, it means you have a brake problem.
Anti-Lock Brake System Warning Light If your vehicle has anti-lock brakes, the anti-lock brake system (ABS) warning light will come on briefly, as a check, when you start your vehicle. If it doesn’t, have your vehicle serviced so that the light works properly when it needs to.
Engine Coolant Temperature Gage This gage on the left measures the temperature of the vehicle’s engine coolant. If the pointer moves into the shaded area, your engine is too hot! If the engine coolant temperature reaches 253° (123°C) the CHK GAGE message will appear and a chime will sound to alert you to the engine coolant temperature gage.
Malfunction Indicator Lamp Service Engine Soon Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition and emission control systems.
If the Light Is Flashing The following may prevent more serious damage to your vehicle: • Reducing vehicle speed. • Avoiding hard accelerations. • Avoiding steep uphill grades. • If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.
Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5 . Poor fuel quality will cause your engine not to run as eff iciently as designed.
Oil Pressure Light If you have a low engine oil pressure problem, this light will stay on after you start your engine, or come on when you are driving. This indicates that your engine is not receiving enough oil. The engine could be low on oil, or could have some other oil problem.
Passlock ® Warning Light Your vehicle is equipped with a Passlock ® theft-deterrent system. With this system, the security light will flash as you open the door if your ignition is off.
Here are four things that some owners ask about. None of these show a problem with your fuel gage: • At the service station, the fuel pump shuts off before the gage reads full. • It takes a little more or less fuel to fill up than the gage indicated.
Low Traction Message If your vehicle has a traction control system (TCS), this LOW TRAC message will be displayed when the system is limiting wheel spin.
Transaxle Fluid Cold Message The TRANS COLD message will be displayed if the automatic transaxle fluid temperature is too cold to operate correctly. When this happens, shifting out of PARK (P) is prevented until the transaxle fluid warms up. Let the engine run for a few minutes until this message is no longer displayed.
Check Gage Message If the CHK GAGE message is displayed, the engine coolant may be overheated. A chime will also sound to alert you to this message. If this message is displayed, check your engine coolant temperature gage. If the needle is in the red area, your engine may be overheating.
Low Fuel Warning Message When the LOW FUEL message is displayed, you may have less than 1.5 gallons (5.5 liters) of fuel left. A chime will also sound to alert you to this message. You should refuel your vehicle immediately. When the fuel tank is filled to more than 3.
Audio System(s) Notice: Before adding any sound equipment to your vehicle, like a tape player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer. Also, check federal rules covering mobile radio and telephone units.
Setting the Time for Radios with Radio Data Systems (RDS) Press and hold the RCL button and at the same time press the HR (AUTO EQ left) or MN (AUTO EQ right) arrows. You will hear a beep indicating that you can change the time. Release the RCL button and press HR until the correct hour appears on the display.
Finding a Station AM FM: Press this button to switch between FM1, FM2, or AM. The display will show the selection. R TUNE Q : Press either arrow to select radio stations. R SEEK Q : Press the up or down arrow to go to the next or to the previous station and stay there.
Using Automatic Set Use this feature to automatically save the radio preset pushbuttons with the stations with the strongest radio signals. A.SET (Automatic Set): Press this button to have the radio automatically select the first 12 strongest radio stations for FM and the six strongest radio stations for AM.
Radio with CD (Base Level) Playing the Radio ON (Power): Push this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease volume. RCL (Recall): Press this knob to switch the display between the radio station frequency and the time.
Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations. You can set up to 18 stations (six FM1, six FM2, and six AM) by performing the following steps: 1. Turn the radio on. 2. Press AM FM to select FM1, FM2, or AM.
Setting the Tone (Bass/Treble) MODE: Press this button until BAS or TRE appears on the display. Press the plus or minus buttons to increase or to decrease. The display will show the bass or the treble level. If a station is weak or noisy, you may want to decrease the treble.
Do not play 3 inch CDs without a standard adapter CD. If an error appears on the display, see “CD Messages” later in this section. 1 PRV (Previous): Press this pushbutton to go to the start of the current track if more than eight seconds have played.
CD Messages If ERR appears on the display and the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smooth, the CD should play.
With RDS, your radio can do the following: • Seek to stations broadcasting the selected type of programming • Receive announcements concerning local and national emergencies • Display messages f.
Finding a Station AM FM: Press this button to switch between FM1, FM2, or AM. The display will show your selection. AUX (Auxiliary): To select XM™ Satellite Radio Service (48 contiguous US states, if equipped), perform the following: 1. Press either CAT arrow to select dif ferent categories.
Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations. You can set up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (48 contiguous US states, if equipped) by performing the following steps: 1.
Setting the Tone (Bass/Treble) QP (Bass/Treble): Press this knob until BASS or TREB appears on the display. Turn this knob to increase or to decrease. The display will show the bass or the treble level. If a station is weak or noisy, you may want to decrease the treble.
RDS Messages ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! will appear on the display. You will hear the announcement, even if the volume is muted or a CD is playing. If a CD is playing, play will stop during the announcement.
Playing the Single CD Player Insert a CD partway into the slot, label side up. The player will pull it in and the CD should begin playing. The CD symbol will appear on the display. You can insert a CD with the ignition off. A CD can also be loaded by pressing the LOAD button.
r CAT (Reverse): Press and hold the left arrow to reverse quickly within a track. Release it to play the passage. The elapsed time of the track will appear on the display. CAT [ (Forward): Press and hold the right arrow to advance quickly within a track.
Playing the Six-Disc CD Player If you turn off the ignition or radio with a CD in the player, it will stay in the player. When you turn on the ignition or radio, the CD will start playing where it stopped, if it was the last selected audio source. As each new track starts to play, the track number will appear on the display.
To load all CDs, do the following: 1. Turn the ignition on. 2. Press and hold the load button for more than three seconds. 3. Load, up to six CDs, in order, starting with the first empty slot. Loading will continue until all six CDs are loaded or load is stopped by pressing any other radio button.
r CAT (Reverse): Press and hold the left arrow to rewind quickly within a track. Release it to play the passage. The elapsed time of the track will appear on the display. CAT [ (Forward): Press and hold the right arrow to advance quickly within a track.
Using an MP3 CD MP3 Format The MP3 radio will play both standard audio CDs and CD-R or CD-RWs. The CD-R/RWs may contain either standard audio (*.cda) or compressed audio (*.mp3). Customers who record their own music CD-R/RWs should be aware of the following: • The files can be recorded on a CD-R/RW disc with a maximum capacity of 700 MB.
Playing an MP3 If you turn off the ignition or radio with a CD in the player, it will stay in the player. When you turn on the ignition or radio, the CD will start playing where it stopped, if it was the last selected audio source. The CD player can play the smaller 8 cm or 3 inch single CDs with an adapter ring.
CD Messages If any error message appears on the display and the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smooth, the CD should play.
Theft-Deterrent Feature The Radio with Single CD (MP3) and the Radio with Six-Disc CD (MP3) have a theft deterrent feature. The theft deterrent feature is designed to discourage theft of your vehicle’s radio. It works by using a secret code to disable all radio functions whenever battery power is interrupted.
6. Press the SEEK/SCAN up or SEEK right arrow to make the second digit agree with your code. 7. Press the TUNE down or AUTO EQ left arrow to make the third digit agree with your code. 8. Press the TUNE up or AUTO EQ right arrow to make the fourth digit agree with your code.
Disabling the Theft-Deterrent Feature Enter your secret code as follows; pause no more than 15 seconds between steps: Preform Steps 1 through 9 from the “Activating the Theft-Deterrent Feature” earlier to enter your secret code. OFF will appear on the display indicating the theft deterrent feature is off.
Care of Your CDs Handle CDs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a CD is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
✍ NOTES 3-72.
Your Driving, the Road, and Your Vehicle ......... .4-2 Defensive Driving .......................................... .4-2 Drunken Driving ............................................ .4-2 Control of a Vehicle ....................................... .4-5 Braking .
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-8 .
Many adults — by some estimates, nearly half the adult population — choose never to drink alcohol, so they never drive after drinking. For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological and developmental reasons for these laws.
There is a gender difference, too. Women generally have a lower relative percentage of body water than men. Since alcohol is carried in body water, this means that a woman generally will reach a higher BAC level than a man of her same body weight will when each has the same number of drinks.
There is something else about drinking and driving that many people do not know. Medical research shows that alcohol in a person’s system can make crash injuries worse, especially injuries to the brain, spinal cord or heart.
Braking Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That is perception time. Then you have to bring up your foot and do it. That is reaction time. Average reaction time is about 3/4 of a second.
When you start your engine, or when you begin to drive away, your anti-lock brake system will check itself. You may hear a momentary motor or clicking noise while this test is going on, and you may even notice that your brake pedal moves or pulses a little.
Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
If your vehicle is in cruise control when the traction control system begins to limit wheel spin, the cruise control will automatically disengage. When road conditions allow you to safely use it again, you may reengage the cruise control. See “Cruise Control” under Turn Signal/Multifunction Lever on page 3-8 .
Steering Tips Driving on Curves It is important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves. Here is why: Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves.
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Of f-Road Recovery You may find that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy.
• Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Loss of Control Let us review what driving experts say about what happens when the three control systems (brakes, steering and acceleration) do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up.
While driving on a surface with reduced traction, try your best to avoid sudden steering, acceleration or braking (including engine braking by shifting to a lower gear). Any sudden changes could cause the tires to slide. You may not realize the surface is slippery until your vehicle is skidding.
Here are some tips on night driving. • Drive defensively. • Do not drink and drive. • Adjust your inside rearview mirror to reduce the glare from headlamps behind you. • Since you can not see as well, you may need to slow down and keep more space between you and other vehicles.
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you can not stop, accelerate or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you can not, try to slow down before you hit them. { CAUTION: Wet brakes can cause accidents.
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
City Driving One of the biggest problems with city streets is the amount of traff ic on them. You will want to watch out for what the other drivers are doing and pay attention to traff ic signals. Here are ways to increase your safety in city driving: • Know the best way to get to where you are going.
Freeway Driving Mile for mile, freeways (also called thruways, parkways, expressways, turnpikes or superhighways) are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traff ic and keep to the right.
Just before you leave the lane, glance quickly over your shoulder to make sure there is not another vehicle in your “blind” spot. Once you are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night.
Here are some things you can check before a trip: • Windshield Washer Fluid: Is the reservoir full? Are all windows clean inside and outside? • Wiper Blades: Are they in good shape? • Fuel, Engi.
Hill and Mountain Roads Driving on steep hills or mountains is different from driving in flat or rolling terrain. If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable.
{ CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they would not work well. You would then have poor braking or even none going down a hill.
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your trunk.
Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You will have a lot less traction or “grip” and will need to be very careful.
Unless you have the anti-lock braking system, you will want to brake very gently, too. If you do have anti-lock, see Braking on page 4-6 . This system improves your vehicle’s stability when you make a hard stop on a slippery road.
• Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, floor mats — anything you can wrap around yourself or tuck under your clothing to keep warm.
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can.
Vehicles Equipped with VTi Variable Transaxle If you press too hard on the accelerator pedal, you may not be able to shift into DRIVE (D) or REVERSE (R).
Dinghy Towing (Manual Transaxle) To tow your vehicle from the front with all four wheels on the ground, do the following: 1. Set the parking brake. 2. Turn the ignition key to ACC. 3. Shift your transaxle to NEUTRAL. 4. Locate and remove the IP BATT2 fuse from the engine compartment fuse block.
Dolly Towing (All Transaxles) To tow your vehicle from the front with two wheels on the ground, do the following: 1. Put the front wheels on a dolly. 2. If you have a five-speed automatic transaxle or VTi variable transaxle, shift the transaxle to PARK (P).
Tire and Loading Information Label A. Vehicle Capacity Weight A. Vehicle Capacity Weight The Tire and Loading Information label shows the seating capacity and the total weight your vehicle can properly carry. This weight is called the vehicle capacity weight.
The Tire and Loading Information label also gives you the size and recommended inflation pressure for the factory-installed, original equipment tires on your vehicle. For more information on tires and inflation see Tires on page 5-58 and Inflation - Tire Pressure on page 5-66 .
Loading Your Vehicle Item Description Total A Vehicle Capacity Weight for Example 1= 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Carg.
Loading Your Vehicle Item Description Total A Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Occupant and C.
If you do have a heavy load, spread it out. Don’t carry more than 167 pounds (75 kg) in your trunk. { CAUTION: Do not load your vehicle any heavier than the GVWR, or either the maximum front or rear GAWR. If you do, parts on your vehicle can break, and it can change the way your vehicle handles.
Towing a Trailer { CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all. You and your passengers could be seriously injured.
If You Do Decide to Pull a Trailer If you do, here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving.
Weight of the Trailer How heavy can a trailer safely be? It should never weigh more than 1,000 lbs. (454 kg). But even that can be too heavy. It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are all important.
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inflated to the upper limit for cold tires. You’ll find these numbers on the Tire-Loading Information label, See Loading Your Vehicle on page 4-33 . Then be sure you don’t go over the GVW limit for your vehicle, including the weight of the trailer tongue.
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer.
Turn Signals When Towing a Trailer When you tow a trailer, your vehicle may need a different turn signal flasher and/or extra wiring. See your retailer if you need information. The arrows on your instrument panel will flash whenever you signal a turn or lane change.
Parking on Hills { CAUTION: You really should not park your vehicle, with a trailer attached, on a hill. If something goes wrong, your rig could start to move. People can be injured, and both your vehicle and the trailer can be damaged. But if you ever have to park your rig on a hill, here’s how to do it: 1.
Maintenance When Trailer Towing Your vehicle will need service more often when you’re pulling a trailer. See Scheduled Maintenance on page 6-4 for more information. Things that are especially important in trailer operation are automatic transaxle fluid (don’t overfill), engine oil, axle lubricant, drive belt, cooling system and brake system.
Service ........................................................... .5-3 Doing Your Own Service Work ........................ .5-4 Adding Equipment to the Outside of Your Vehicle ..................................................... .5-4 Fuel ........
Windshield Wiper Blade Replacement ............. .5-57 Tires ............................................................. .5-58 Inflation - Tire Pressure ................................ .5-66 Tire Inspection and Rotation .......................... .
Service Your Saturn retailer knows your vehicle best and wants you to be happy with it. We hope you will go to your retailer for all your service needs. You will get genuine Saturn parts and Saturn-trained and supported service people. We hope you will want to keep your Saturn vehicle all Saturn.
Doing Your Own Service Work If you want to do some of your own service work, you will want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-10 .
Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle. Gasoline Octane If your vehicle has the 2.2L L4 engine, use regular unleaded gasoline with a posted octane of 87 or higher. If the octane is less than 87, you may get a heavy knocking noise when you drive.
California Fuel If your vehicle is certified to meet California Emission Standards (see the underhood emission control label), it is designed to operate on fuels that meet California specifications.
Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in your fuel system and also damage the plastic and rubber parts. That damage would not be covered under your warranty.
Filling Your Tank { CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when CAUTION: (Continued) CAUTION: (Continued) you are refueling.
{ CAUTION: If you get fuel on yourself and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any “hiss” noise to stop.
Checking Things Under the Hood { CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan. { CAUTION: Things that burn can get on hot engine parts and start a fire.
2. Then go to the front of the vehicle and push the hood release latch to the side. 3. Lift the hood, release the hood prop from its retainer and put the hood prop into the slot in the hood. Before closing the hood, be sure all the filler caps are on properly.
Engine Compartment Overview When you open the hood on 2.2L L4 engine, you’ll see the following: 5-12.
A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-22 . B. Engine Oil Fill Location. See Engine Oil on page 5-15 . C. Engine Oil Dipstick Location. See Engine Oil on page 5-15 . D. Brake Master Cylinder. See Brakes on page 5-38 and Hydraulic Clutch on page 5-25 .
When you open the hood on 2.0L Supercharged engine, you’ll see the following: 5-14.
A. Engine Oil Dipstick Location. See Engine Oil on page 5-15 . B. Electric Cooling Fan. See Cooling System on page 5-32. C. Engine Oil Fill Location. See Engine Oil on page 5-15 . D. Radiator Pressure Cap. See Engine Coolant on page 5-26. E. Brake Master Cylinder.
When to Add Engine Oil If the oil is at or below the MIN mark, then you will need to add at least one quart of oil. But you must use the right kind. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-102 .
• SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. However, if it is going to be 0°F (–18°C) or above and SAE 5W-30 is not available, you may use SAE 10W-30. These numbers on an oil container show its viscosity, or thickness.
GM Goodwrench oil meets all the requirements for your vehicle. If you are in an area of extreme cold, where the temperature falls below − 20°F ( − 29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil.
• SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. However, you can use SAE 10W-30 if it is going to be 0°F (-18°C) or above. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
When to Change Engine Oil (GM Oil Life System) Your vehicle has a computer system that lets you know when to change the engine oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably.
After changing the engine oil, reset the system by doing the following: 1. Press and release the trip/reset button until the OIL LIFE message is displayed. 2. Then press and hold the trip/reset button until a chime sounds five times, and RESET is displayed in the message center.
Engine Air Cleaner/Filter Engine Air Cleaner/Filter Replacement When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at every oil change and replace at the first oil change after 25,000 miles (40,000 km).
How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter remove the filter from the vehicle and lightly shake filter to release loose dust and dirt. If the filter remains “caked” with dirt, a new filter is required. The engine air cleaner/filter is located in the engine compartment.
3. Pull the air cleaner/filter box cover out and remove the air filter element from the air filter box. If the element is dirty, you should replace it. If the element is only dusty, it may be cleaned by blowing compressed air through it from the clean side.
If you do not use your vehicle under any of these conditions, the fluid and filter do not require changing. Notice: For VTi variable transaxles, use only Saturn Variable Transaxle Fluid.
Engine Coolant The cooling system in your vehicle is filled with DEX-COOL ® engine coolant. This coolant is designed to remain in your vehicle for 5 years or 100,000 miles (166 000 km), whichever occurs first, if you add only DEX-COOL ® extended life coolant.
CAUTION: (Continued) Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning. Your engine could catch fire and you or others could be burned.
Checking Coolant The surge tank is located on the driver’s side of the engine compartment. See Engine Compartment Overview on page 5-12 for more information on location. { CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Adding Coolant If you need more coolant, add the proper DEX-COOL ® coolant mixture at the surge tank , but only when the engine is cool. See Cooling System on page 5-32 for instructions on how to add coolant to the coolant surge tank. { CAUTION: You can be burned if you spill coolant on hot engine parts.
If Steam Is Coming From Your Engine { CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
If No Steam Is Coming From Your Engine An overheat warning can indicate a serious problem. See Low Coolant Level Warning Message on page 3-43 . If you get an engine overheat warning with no warning messages, but see or hear no steam, the problem may not be too serious.
Cooling System When you decide it’s safe to lift the hood, here’s what you’ll see: A. Electric Engine Fan B. Coolant Surge Tank with Pressure Cap { CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
The coolant level should be at the cold fill line. If it isn’t, you may have a leak at the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system. { CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
How to Add Coolant to the Coolant Surge Tank If you haven’t found a problem yet, check to see if coolant is visible in the surge tank. If coolant is visible but the coolant level isn’t at the cold.
CAUTION: (Continued) Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning. Your engine could catch fire and you or others could be burned.
3. Fill the coolant surge tank with the proper DEX-COOL ® coolant mixture, to the cold fill line. 4. With the coolant surge tank pressure cap of f, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan.
Windshield Washer Fluid What to Use When you need windshield washer fluid, be sure to read the instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has suff icient protection against freezing.
Brakes Brake Fluid Your brake master cylinder reservoir is filled with DOT-3 brake fluid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down.
Checking Brake Fluid You can check the brake fluid level without removing the reservoir cap by just looking at the brake fluid reservoir. The fluid level should be at or below the MAX fill mark. After work has been done on the brake hydraulic system, make sure the level does not exceed the MAX fill mark on the reservoir.
Brake Wear Your vehicle has front disc brakes and rear drum brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal firmly).
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking.
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to follow the steps below to do it safely. { CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you.
4. Open the hoods and locate the batteries. Find the positive (+) and negative ( − ) terminal locations on each vehicle. You will not need to access your battery for jump starting. Your vehicle has a remote positive (+) jump starting terminal for that purpose.
{ CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables don’t have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged, too.
7. Don’t let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( − ) cable to the negative ( − ) terminal of the good battery.
10. Now start the vehicle with the good battery and run the engine for a while. 11. Press UNLOCK on the RKE transmitter to disarm your security system (if equipped). 12. Try to start the vehicle that had the dead battery. If it won’t start after a few tries, it probably needs service.
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( − ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative ( − ) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery.
Bulb Replacement For the type of bulb to use, see Replacement Bulbs on page 5-56 . For any bulb changing procedure not listed in this section, contact your retailer. Halogen Bulbs { CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
4. To access the headlamp bulb, turn the dust cap counter-clockwise to remove it. 5. Raise the lock tab and pull the connector from the base of the bulb to remove the electrical connector from the headlamp bulb.
6. To remove the bulb retaining nut, turn it counter-clockwise. 7. Remove the bulb and replace it with the appropriate bulb. Headlamps (Coupe) 1. Turn the ignition and headlamp switch of f. 2. After allowing the bulb to cool, open the hood. See Hood Release on page 5-10 .
4. Remove the retaining nut. 5. Remove the bulb and replace it with the appropriate bulb. Front Turn Signal Lamps (Sedan) 1. Turn the ignition and headlamp switch of f. 2. After allowing the bulb to cool, open the hood. See Hood Release on page 5-10 .
4. To access the park/turn bulb, turn the dust cap counter-clockwise to remove it. 5. Remove the park/turn bulb socket and bulb by rotating it counter-clockwise.
Front Turn Signal and Parking Lamps (Coupe) 1. Open the hood. See Hood Release on page 5-10 . 2. Reach behind the headlamp from inside the hood. 3. Rotate the bulb socket counter-clockwise to remove it from the housing. 4. Gently pull the bulb from the socket and replace it with the appropriate bulb.
Sidemarker Lamps (Coupe) 1. Turn the ignition and headlamp switch of f. 2. Open the hood. See Hood Release on page 5-10 . 3. Pull up on the headlamp retaining pins to remove them, gently pull the headlamp assembly away from the vehicle and remove the electrical connector.
Center High-Mounted Stoplamp (CHMSL) 1. Remove the CHMSL cover by pulling down on the cover edges. 2. Twist the sockets out of the stop lamp and remove the bulbs. 3. Replace with the appropriate bulbs. Taillamps, Stoplamps and Back-up Lamps 1. Open the trunk.
4. Remove the bulb socket by rotating 1/8 of a turn counter-clockwise. 5. Gently pull the bulb from the socket and replace it with the appropriate bulb.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear or cracking. See “Windshield Wipers, Blade Check” under Scheduled Maintenance on page 6-4 for more information. Replacement blades come in different types and are removed in different ways.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
Low-Profile Performance Tire (Red Line) If your vehicle has 215/45ZR17 size tires, they are classified as “low-profile performance” tires. These tires are designed for very responsive driving on wet or dry pavement. You may also notice more road noise with low-profile performance tires and that they tend to wear faster.
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. (A) Tire Size: The tire size code is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type and service description.
(A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat.
Tire Size The following illustration shows an example of a typical passenger car tire size. (A) P-Metric Tire: The United States version of a metric tire sizing system. The letter “P” as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories.
GAWR RR: Gross Axle Weight Rating for the rear axle, see Loading Your Vehicle on page 4-33 . Intended Outboard Sidewall: The side of an asymmetrical tire that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure.
Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface.
Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right.
How to Check Use a good quality pocket-type gage to check tire pressure. You can’t tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they’re underinflated. Check the tire’s inflation pressure when the tires are cold.
Tire Inspection and Rotation Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). Any time you notice unusual wear, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-69 and Wheel Replacement on page 5-72 for more information.
After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 5-102 .
Buying New Tires To find out what kind and size of tires your vehicle needs, look at the tire and loading information label. For more information about this label and its location on your vehicle, see Loading Your Vehicle on page 4-33 .
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A Th.
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new Saturn original equipment parts.
Tire Chains { CAUTION: If your vehicle has P195/60R15, P205/55R16 or 215/45ZR17 size tires, don’t use tire chains, there’s not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts.
If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers. { CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Removing the Spare Tire and Tools The equipment you’ll need is located in the trunk. 1. Lift the trunk liner and place the plastic hook in the lip of the trunk lid.
2.2 L4 Engine 2.0L Supercharged Engine 5-78.
2. Remove the nut that holds down the spare tire. See Compact Spare Tire on page 5-86 3. Remove the spare tire by placing your hands at the four and eight o’clock positions. Gently pull it up and out of the trunk. For vehicles equipped with the 2.0L supercharged engine, complete Step 4 first, then Step 3.
Press the button and then pull on the end of the wheel wrench to extend the handle. Removing the Flat Tire and Installing the Spare Tire 1. If your vehicle is equipped with plastic wheel covers, use the wheel wrench to loosening the plastic wheel nut caps.
3. Position the jack lift head at the jack location nearest the flat tire. The front location is about 7 inches (17.8 cm) rearward from the front wheel opening. The rear location is about 2 inches (5.1 cm) forward of the rear wheel opening. Make sure the jack head is touching the metal jacking flange under the body.
6. Remove all of the wheel nuts. 7. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. { CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident.
11. Tighten the wheel nuts firmly in a crisscross sequence, as shown. { CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts.
Storing the Flat or Spare Tire and Tools { CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
1. Remove the stow bolt extension rod and sleeve from the jack. 2. Reattach the wheel wrench to the jack. 3. Screw the stow bolt extension rod and the sleeve into the existing spare tire hold-down bolt. 4. Place the flat tire face down into the spare tire hub.
Compact Spare Tire Although the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation pressure regularly.
Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flames if you strike a match or get them on a hot part of the vehicle.
Here are some cleaning tips: • Always read the instructions on the cleaner label. • Clean up stains as soon as you can — before they set. • Carefully scrape off any excess stain. • Use a clean cloth or sponge, and change to a clean area often.
Cleaning Vinyl Use warm water and a clean cloth. • Rub with a clean, damp cloth to remove dirt. You may have to do this more than once. • Things like tar, asphalt and shoe polish will stain if you do not get them off quickly. Use a clean cloth and vinyl cleaner.
Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent applications may be required. See Recommended Fluids and Lubricants on page 6-14 .
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible.
Cleaning Tires To clean your tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Vehicle Care/Appearance Materials See your Saturn retailer for more information on purchasing the following products. Vehicle Care/Appearance Materials Description Usage Polishing Cloth Wax-Treated Interior and exterior polishing cloth. Tar and Road Oil Remover Removes tar, road oil and asphalt.
Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Instrument Panel Fuse Block Some fuses are in a fuse block on the driver’s side of the vehicle, near the driver’s right leg. Loosen the screw on the cover and remove the cover.
Fuses Usage FUEL PUMP Fuel Pump Relay HVAC Climate Control CLUSTER Instrument Panel Cluster LIGHTER Cigar Lighter RADIO (BATT1) Radio Receiver, Entertainment Memory RADIO (ACC) Radio Receiver, Enterta.
Engine Compartment Fuse Block (2.2L L4 Engine) Some fuses are in a fuse block in the engine compartment on the driver’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location.
Fuses Usage 18 HDLP-LH Driver’s Side Headlamp 19 WIPER Wiper Mini Relay 20 HORN Horn Micro Relay 21 PREM AUDIO Entertainment, Premium Radio Amplifier 22 ABS Anti-Lock Brake System, Traction Control.
Engine Compartment Fuse Block (2.0L Supercharged Engine) Some fuses are in a fuse block in the engine compartment on the driver’s side of the vehicle.
Fuses Usage 22 ABS Anti-Lock Brake System 23 RR DEFOG Rear Defog Mini Relay 38 RUN/CRANK Ignition 1 Mini Relay 39 IP BATT1 Body Control Module 40 ABS Anti-Lock Brake System 41 IP BATT2 Body Control Mo.
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-14 for more information. Application Capacities English Metric Air Conditioning Refrigerant R134a Use Refrigerant Oil, R134a Systems 0.
Engine Specifications Engine VIN Code Transaxle Spark Plug Gap 2.2L L4 (L61) F Five-speed manual Five-speed automatic VTi variable 0.045 inches (1.0 mm) 2.
✍ NOTES 5-104.
Maintenance Schedule ..................................... .6-2 Introduction .................................................. .6-2 Maintenance Requirements ............................. .6-2 Your Vehicle and the Environment ................... .6-2 Using Your Maintenance Schedule .
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition.
This schedule is for vehicles that: • carry passengers and cargo within recommended limits. You will find these limits on the tire and loading information label. See Loading Your Vehicle on page 4-33 . • are driven on reasonable road surfaces within legal driving limits.
Scheduled Maintenance When the CHG OIL message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km).
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. Reset oil life system. See Engine Oil on page 5-15 . An Emission Control Service. •• Visually check for any leaks or damage. See footnote (j). •• Inspect engine air cleaner filter.
Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item.
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (41 500) 50,000 (83 000) 75,000 (125 000) 100,000 (166 000) 125,000 (207 500) 150,000 (240 000) Replace spark plugs. An Emission Control Service. • Replace engine fuel filter.
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life.
(h) Change automatic transaxle or VTi variable transaxle fluid and filter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traff ic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain.
At Each Fuel Fill It is important to perform these underhood checks at each fuel fill. Engine Oil Level Check Check the engine oil level and add the proper oil if necessary. See Engine Oil on page 5-15 for further details. Notice: It is important to check your oil regularly and keep it at the proper level.
At Least Once a Year Starter Switch Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake.
Automatic Transaxle Shift Lock Control System Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle.
Parking Brake and Automatic Transaxle Park (P) Mechanism Check { CAUTION: When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer. Usage Fluid/Lubricant Engine Oil (2.2L engine) Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Usage Fluid/Lubricant Hydraulic Brake System Delco Supreme 11 Brake Fluid or equivalent DOT-3 brake fluid. Windshield Washer Solvent Optikleen ® Washer Solvent. Parking Brake Cable Guides Chassis Lubricant (GM Part No. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.
Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your retailer. Part Saturn Part Number AC Delco Part Number Engine Air Cleaner/Filter 2.2L L4 Engine 2.0L Supercharged 22679620 — — — Engine Oil Filter 2.
Engine Drive Belt Routing 2.2L Four Cylinder (L61) Engine 2.0L Supercharged (LSJ) Engine 6-17.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-19.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-20.
Customer Assistance and Information .............. .7-2 Customer Satisfaction Procedure ..................... .7-2 Online Owner Center ..................................... .7-4 Customer Assistance for Text Telephone (TTY) Users ......................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your retailer and to Saturn. Together we are committed to providing our customers with unparalleled service, before, during and after the purchase of a Saturn vehicle, for total customer satisfaction.
In Canada, write to: Saturn Customer Communication Centre General Motors of Canada Ltd. 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 When contacting Saturn, please remember that your concern will likely be resolved at a retailer’s facility. That is why we suggest you follow Step One first if you have a concern.
Online Owner Center The Owner Center is a resource for your GM ownership needs. You can find your specific vehicle information all in one place. The Owner Center allows you to: • Get e-mail service reminders. • Access information about your specific vehicle, including tips and videos and an electronic version of this owner’s manual.
GM Mobility Program for Persons with Disabilities This program, available to qualified applicants, can reimburse you up to $1,000 toward eligible aftermarket driver or passenger adaptive equipment you may require for your vehicle (hand controls, wheelchair/ scooter lifts, etc.
We will provide the following services during the Bumper-to-Bumper warranty period at no expense to you: • Fuel Delivery: Delivery of enough fuel ($5 maximum) for the customer to get to the nearest service station.
While we hope you never have the occasion to use our service, it is added security while traveling for you and your family. Remember we are only a phone call away. Saturn Roadside Assistance: 1-800-553-6000; text telephone (TTY) users, call 1-800-833-6000.
This information has been used to improve vehicle crash performance and may be used to improve crash performance of future vehicles and driving safety. Unlike the data recorders on many airplanes, these on-board systems do not record sounds, such as conversation of vehicle occupants.
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traff ic Safety Administration (NHTSA), in addition to notifying Saturn Corporation.
Service Publications Ordering Information Service Manuals A variety of publications are available to you. Saturn service manuals are written for trained technicians, and in some cases, specialized tools and equipment are necessary to complete certain repairs.
A Accessory Power Outlets ................................. 3-18 Activating the Theft-Deterrent Feature ................ 3-68 Adding Windshield W asher Fluid ....................... 5-37 Additives, Fuel ................................................
Automatic Headlamp System ............................ 3-16 Automatic T ransaxle ........................................ 2-20 Fluid .......................................................... 5-24 Operation ............................................
Change Engine Oil Message ............................ 3-43 Changing a Tire When T railer T owing ................ 4-46 Changing the Language (Canada Only) .............. 3-41 Check Engine Light ............................................... 3-36 Check Gage Message .
Convenience Net ............................................ 2-45 Coolant Engine T emperature Gage ............................ 3-35 Heater , Engine ............................................ 2-22 Low Level W arning Message .........................
Driving (cont.) Drunken ....................................................... 4 - 2 Freeway ..................................................... 4-21 Hill and Mountain Roads .............................. 4-24 In Rain and on Wet Roads .............
F Filter Engine Air Cleaner ...................................... 5-22 Finding a Category (CA T) Station ...................... 3-58 Finding a Station ............................ 3-48, 3-50, 3-56 Finish Care .........................................
H Hazard W arning Flashers ................................... 3 - 6 Head Restraints ............................................... 1 - 5 Headlamp Aiming ....................................................... 5-47 Headlamp High/Low-Beam Changer ....
J Jump Starting ................................................. 5-42 K Keyless Entry System ....................................... 2 - 4 Keys ............................................................... 2 - 3 L Lamps Exterior ...................
M Maintenance Schedule Additional Required Services ........................... 6 - 6 At Each Fuel Fill ......................................... 6-10 At Least Once a Month ................................ 6-10 At Least Once a Y ear ..................
N New V ehicle Break-In ...................................... 2-18 Normal Maintenance Replacement Parts ............ 6-16 O Odometer ...................................................... 3-29 Off-Road Recovery .......................................
Power (cont.) Steering Message ........................................ 3-44 Windows .................................................... 2-15 Pretensioners, Safety Belt ................................ 1-28 Programmable Automatic Door Locks .........
Reporting Safety Defects Canadian Government ................................... 7 - 9 Saturn ......................................................... 7 - 9 United States Government .............................. 7 - 9 Restraint System Check Checking Y our Restraint Systems .
Service ........................................................... 5 - 3 Adding Equipment to the Outside of Y our V ehicle .............................................. 5 - 4 Doing Y our Own Work ................................... 5 - 4 Engine Soon Light .
Theft-Deterrent System ...................................... 2 - 6 Theft-Deterrent Systems ................................... 2-17 Passlock ® ................................................... 2-17 T ilt Wheel .....................................
U Understanding Radio Reception ........................ 3-70 Uniform T ire Quality Grading ............................ 5-71 Unlocking the Theft-Deterrent Feature After a Power Loss ...................................... 3-69 Up-Shift Light .........
Windows ....................................................... 2-14 Manual ...................................................... 2-15 Power ........................................................ 2-15 Windshield W asher ............................
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Saturn 2004 Ion è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Saturn 2004 Ion - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Saturn 2004 Ion imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Saturn 2004 Ion ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Saturn 2004 Ion, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Saturn 2004 Ion.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Saturn 2004 Ion. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Saturn 2004 Ion insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
