Manuale d’uso / di manutenzione del prodotto HEC-DR7700K del fabbricante Sanyo
Vai alla pagina of 16
CONTENTS PAGE Be sure to read this manual thoroughly in order to ensure proper use. In particular, make certain to read the section " I M P O R T A N T S A F E T Y I N S T R U C T I O N S " . Kee p thi s man ual i n a saf e pla ce so that it ca n be f ound e asil y.
2 IMPORTANT SAFETY INSTRUCTIONS 1 All of the following information is important. Be sure to follow the instructions carefully. Wh e n u s i ng a n e l ec t r ic a l ap p li a n ce , ba s i c p r e ca u ti o n s s h ou l d al w a ys b e f o ll o w ed , in c l ud i n g t h e following: Read all instructions before using this appliance.
4 3 Be careful not to spill water over the remote control, sensor controller, seat, or foot rest. Otherwise, electric shock, short circuit or fire may occur. Do not suddenly release your hand, while raising the foot rest. Otherwise, an injury may occur.
6 5 NAME/FUNCTION OF EACH PART Caster Used when moving the chair. Back rest Back pad Arm rest Head cover Seat Remote control Sensor controller Massaging rollers Cord Power plug Grounding pin Cover A Foot rest slide lever Foot rest Cover B Stand Installation screws (3 screws) Check the accessories at first.
8 7 NAME/FUNCTION OF EACH PART REPEAT! display Turns on during Whole Body Sensor Automatic Courses and Automatic Courses. The ring lights up by pressing the REPEAT! button when you want to repeat your desired massage during the course of massaging.
10 9 HOW TO INSTALL THE STAND Installation screws 1 Remove the covers on the outer sides of the arm rests. Insert the flathead screwdriver into the holes under the cover and pull toward you. (4 places) 5 Put the cords of the remote control and sensor controller in the cord hook on the back of the body.
12 11 HOW TO USE PREPARATIONS PRIOR TO USE ① ③ Press the OPERATION ON/OFF button. Select a massaging course. (See page 16-24) ② Adjust the angle of back rest and foot rest with the ZERO-G button, RECLINING button and FOOT REST UP and DOWN button.
14 13 ADJUSTMENT OF CHAIR Before sitting on the massage chair OR (Remote control) (Sensor controller) Raise the back rest, and lower the foot rest by continuously pressing the UP ( ) button. Recline the back rest, and raise the foot rest by continuously pressing the DOWN ( ) button.
16 15 ADJUSTMENT OF CHAIR MASSAGING (WHOLE BODY SENSOR AUTOMATIC COURSES) Ref er to the page 27 and 2 8 re gardi ng t he ma ssagi ng c onten ts o f Who le B ody S enso r Aut omati c Co urses . Cha nge o f co urse duri ng ma ssag ing, or c hange to t he A utoma tic Cours e or the Manu al Co urse, is possi ble.
18 17 MASSAGING (WHOLE BODY SENSOR AUTOMATIC COURSES) 7 Adjust the strength of massage. (See page 18) ③ Massages according to the stiffness. Adjusts the operation and strength of standard massaging according to the measured degree of stiffness. → Massaging operation and the display of remote control.
20 19 MASSAGING (AUTOMATIC COURSES) ① Measure the position of shoulder. ② Starts the massaging of selected course. Check if the position of shoulder is correct.
22 21 MASSAGING (MANUAL COURSES) 7 Adjust the height, width, speed, and strength of the massaging rollers. There are some adjustments which are not possible, depending on the type of massage chosen. (See page 23) Adjusting the height of massaging rollers.
24 23 Several types of desired massage can be selected. It is possible to adjust the movement speed, height position and width of massaging rollers and the strength of massage. (There are some adjustments that are not possible, depending on the kind of massaging.
26 25 AFTER USE 2 Turn off the POWER. 1 Set the back rest and the foot rest to the starting position. Be sure to check that there are no children, pets, or any obstacles around the massager. MAINTENANCE PROCEDURES Perform daily maintenance by wiping with a soft dry cloth.
28 〈 WHOLE BODY SENSOR AUTOMATIC COURSE 〉 〈 AUTOMATIC COURSE 〉 Standard massage in FINE Course WAIST Course NECK/SHOULDER Course Spine stretching Shiatsu (Shoulder) Tapping/Kneading (Shoulder,.
29 TROUBLE-SHOOTING Type of Trouble The operation stops in the middle of massaging in the Whole Body Sensor Automatic Course or Automatic Course Movement of massaging rollers in upward direction, causing operation to stop Check points Countermeasure You feel discomfort during the operation of reclining.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Sanyo HEC-DR7700K è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Sanyo HEC-DR7700K - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Sanyo HEC-DR7700K imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Sanyo HEC-DR7700K ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Sanyo HEC-DR7700K, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Sanyo HEC-DR7700K.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Sanyo HEC-DR7700K. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Sanyo HEC-DR7700K insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
