Manuale d’uso / di manutenzione del prodotto HL-P4667W del fabbricante Samsung
Vai alla pagina of 16
Remote Control (BP59-00076A)/ AAA Batteries Once you have unpacked your TV , check to make sure that you have all the parts shown here. If any piece is missing or broken, call your dealer .
Connecting VHF and UHF Antennas 1 Place the wires from the twin leads under the screws on the 300-75 ohm adaptor (not supplied). Use a screwdriver to tighten the screws. 2 Plug the adapter into the “Air IN” terminal on the rear panel. If you do not have a cable system, you will need to connect an antenna to your TV .
Connecting Cable TV and VCR • When you use a converter box with your TV , there may be fea- tures that you can not program using the remote control, such as programming your favorite channels and blocking chan- nels. • The output from "Cable Out" is not available when "Air/CA TV" is set to "Cable" in the PIP menu.
Connecting CableCARD 1 2 Insert the CableCARD into the “CableCARD” slot and the message “CableCARD Inserted” is displayed on the screen. If the channel information does not already exist, the message “Updating Channel List” is displayed during channel information configura- tion.
Connecting a DVD Player Connecting a Camcorder 1 2 Locate the A/V output jacks on the camcorder . They are usually found on the side or back of the camcorder . Connect a set of audio cables between the AUDIO IN jacks on the TV and the AUDIO OUT jacks on the camcorder .
Connecting a DTV Set-T op Box 1 2 Connect a set of audio cables between the Audio in (1 or 2) jacks on the TV and the AUDIO OUT jacks on the DVD player . Connect a video cable between the VIDEO IN (1 or 2) jack on the TV and the VIDEO OUT jack on the DVD player .
Connecting to HDMI (High Definition Multimedia Interface) 1 2 Connect a set of audio cables between the DVI audio (L,R) in jacks on the TV and the AUDIO OUT jacks on the Set-T op Box. Connect an HDMI/DVI video cable between the HDMI/DVI IN jack on the TV and the DVI OUT jack on the Set-T op Box.
Connecting to an Analog Amplifier Connecting a Digital Audio System 1 If your audio system has a optical dig- ital audio input, connect to the “DIGI- TA L AUDIO OUT(OPTICAL)” jack on the TV . Be certain to remove the black cover from the optical output before insert- ing the cable.
Remote Control Œ POWER T urns the TV on and off. ´ P .MODE Adjust the TV picture by selecting one of the preset factory settings (or select your personal, customized picture settings.) ˇ ANTENNA Press to select “AIR” or “CABLE”. ¨ CHANNEL NUMBER Press to directly tune to a particular channel.
T urning the TV On and Off Press the POWER button on the remote control. Y ou can also use the POWER button on the front panel. V iewing the Menus and On-Screen Displays The on-screen menu system allows you to control the settings of your TV . Access the on- screen menu system by pressing the Menu button on the remote control.
Memorizing the Channels Y our TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits.
4 Press the … or † button to select the Antenna connection, then press the ENTER button. • Air : “Air” antenna signal Cable : “Cable” antenna signal Air+Cable : “Air” and “Cable” antenna signals • If the CableCARD is inserted into the“CableCARD” slot on the rear panel, “Cable” and “Air+Cable” are not avail- able.
V iewing an External Signal Source Use the remote control to switch between viewing signals from connected equipment, such as a VCR, DVD, Set-T op box or the TV source (broadcast or cable). V iewing Position To optimize your viewing comfor t, please follow the guidelines below for viewing distance.
Replacing the Lamp Why do I need to replace the lamp? The lamp used in a DLP TV has a limited lifespan. For the best screen quality it needs to be replaced periodically .
Front Panel LED Indicators The three lights on the front panel indicate the status of your TV . : Light is On : Light is Blinking : Light is Off • It takes about 30 seconds for the TV to warm up, so normal brightness may not appear imme- diately . • The TV has a fan to keep the inside lamp from overheating.
Memo 16 BP68-00429A-00Eng 11/10/04 3:18 PM Page 16.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Samsung HL-P4667W è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Samsung HL-P4667W - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Samsung HL-P4667W imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Samsung HL-P4667W ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Samsung HL-P4667W, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Samsung HL-P4667W.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Samsung HL-P4667W. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Samsung HL-P4667W insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
