



RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
shock, or damage to the product. 3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire. 4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire. 5. When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury. 6. Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service centre. Continued use in such a condition may cause fire or electric shock.
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

as sun, as this may damage the CCD image sensor. 8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. 9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibration or magnetic interference. 2. Do not install in a location subject to high temperature (over 122°F), low temperature (below 14°F), or high humidity. Doing so may cause fire or electric shock. 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fire or damage to the product. 5. Keep out of direct sunlight and heat radiation sources. It may cause fire. 6. Install it in a place with good ventilation. 7. Avoid aiming the camera directly towards extremely bright objects such




This enriched WDR (Wide Dynamic Range) Day/Night camera can clearly implement both dark and bright parts on the screen with the dual shutter. When a bright object such as window occupies a part of the screen, it appears white in conventional cameras. But using the state-of-the-art WDR function that this camera provides, you can see the clear image. This Day/Night camera activates the colour mode when in the illumination over the normal value. Otherwise it activates B/W (Black/White) mode by removing the IR cut function, which can improve the sensitivity for identifying objects even in a dark area. It also incorporated the low speed shutter and Sens-Up (Uses the field accumulation method) functions to enhance the low illumination feature. This camera can be mainly used in the dark places such as basement parking lots under comparatively low illumination. In daytime, it displays the colour screen with a horizontal resolution of 540 lines but at night, it uses the Day/Night feature along with the Sens-Up function to identify objects in a dark area. You can also connect the infrared ray emission equipment to this camera. Moreover, this camera has more various functions for surveillance. White Balance function that provides accurate colour rendition under any light conditions. Auto Focus function that automatically tracks and focuses on the moving subject. Privacy Zone function to hide a special area for privacy protection. RS485/ Wired remote control function.

High Sensitivity It implements images of high sensitivity using the up-to-date Super-HAD IT CCD(SCC-C4233(P)/C4333(P))/ExView-HAD PS CCD(SCC-C4235(P)/C4335(P)). WDR The WDR function of this camera is the state-of-the-art technology that can effectively enlarge the range for screen gain. It is mainly used for taking photos for window scenes inside a building. Using this technology, you can clearly see both indoor and outdoor images, and can enjoy the excellent picture quality, which is enabled by automatically adjusting the WDR level.
Low Illumination It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera identify objects even in the worst environment. Superior Backlight Adjustment When an object has a bright illumination or sunlight behind it, this camera automatically improves the shaded object picture quality. Digital Power Synchronization The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the operation ability and reliability of this camera.
High Resolution This camera has realized high resolution of 540 lines using the top-notch full digital image processing and special algorithm technologies. Output Signal Setting You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy, Horizontal/Vertical profiling, POSI/NEGA function, and digital zooming. White Balance It uses to automatically adjust light levels to improve colour balance depending on the illumination. Auto Focus It enables to capture clear images by adjusting the automatic focus on the subject movement.


1 Input/Output Connector This connector has input and output jacks for RS-485 control signals.
RS-485 DATA+ Jack for connection to RS-485 DATA+ signal line.


5-7. ZOOM/ FOCUS REMOTE terminals This port is used for ZOOM/FOCUS, MENU CONTROL, HOME RETURN, and ONEAF by using an external controller. Depending on the input condition, 4 modes, A, B, C, and D are available. (SPECIAL - CTRL TYPE) (Operation Voltage Range : +3V~+13V, -3V~-13V)
*1: During MENU OFF, controls ZOOM/FOCUS and during MENU ON, changes the direction, Up/Down/Left/Right SETUP switch.


* 2 : For short voltage supply during MENU OFF, executes ONEAF and for more than 2 second * 3 : For more than 2 second long voltage supply, moves to the PRESET 0(HOME) position. 2 SETUP Switch This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the Setup menu appears.
n [Left/Right] movement or changing the displayed value: By
pressing this switch left or right, you can move left or right on the menu or change the displayed value.
can move up or down on the menu.
value or function is confirmed. To enter a submenu, press this button.
3 Power Display LED When the power is normally connected, the red LED lights.
4 Video OUT Jack This is connected to the Video Input jack of the monitor and it outputs the Video signals. 5 Power Connection Jack This is connected to the Power cable.


Make sure that the following items are included in the package.
n Do not disassemble the camera on your own.
n Always be careful when handling the camera. Do not strike the
camera by your fists or shake it. Please be careful not to be careless when storing and operating it.
n Do not place or operate the camera in any wet environment
n Do not clean the camera with rough sandpaper. Please always
n Put the camera in a cool area free from direct sunlight.


To install and use the camera, first prepare the following cables.
The requirements for the power adapter, which connects to the camera’s POWER IN terminal, are as follows:
Use a BNC cable, such as the one shown below, to connect the camera’s VIDEO OUT to the monitor.





ADDRESS 0 TYPE RS-485, HALF BAUD RATE 9600 ROM VER 1.000 EEP VER 1.000 LENS OK.
* ROM VER and EEP VER may change without notice.


This chapter describes how to configure the camera-related settings. If you press the SETUP switch for at least 2 seconds, the Setup menu appears. The Setup OSD (On-screen Display) map brief is like the following:
SHUTTER OFF/AUTO X2 ~ AUTO X256 /1/100(1/120) ~ 1/10K

The [CAMERA ID] menu is used to assign a camera ID to this camera. If you press the SETUP switch when the [CAMERA ID] menu is selected, the corresponding setup screen appears.
CAMERA ID ON... IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
(CAMERA ID) ABCDEFGHIJKLMNOPQRSTUVWXYZ 0123456789 : ! - + * () /
RET SP▶▶ ◀◀SP LOCATION... CAMERA-1
You can input a camera ID composed of alphabets, numbers, and special characters up to 20 characters long. The input camera ID can be displayed at the desired location when using the [LOCATION…] submenu. When you press the SETUP switch in [RET], the screen returns to the upper menu.
The [IRIS] menu is used to set the automatic light control method for this camera.

WDR...
If you press the SETUP switch when the [WDR…] submenu is selected, the corresponding screen appears.
CAMERA ID OFF IRIS WDR... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
LEVEL1 L I H LEVEL2 L I H WHITE BAL INDOOR RET
You can adjust the shutter speed in [LEVEL1] and the brightness in [LEVEL2]. You can also select any of [ALL], [OUTDOOR], and [IN DOOR] in [WHITE BAL]. In case of [ALL], this camera controls both indoor and outdoor images.
ALC...
If you press the SETUP switch when the [ALC…] submenu is se lected, the corresponding screen appears.
CAMERA ID OFF IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
BLC OFF LEVEL ( 0) I RET

You can make the BLC (Back Light Compensation) function active or not. For setting the BLC zone, you can select any of [BOTTOM…], [TOP…], [LEFT…], [RIGHT…], and [CENTER…]. The actual location is displayed when you enter each item. In case of [USER…], you can set the desired BLC zone by defining the size and location. You can set the Video output level in [LEVEL]. Its selectable range is from -9 to +9.
If you press the SETUP switch after selecting MANU in the IRIS item, an additional screen appears in which you can set manually opening or closing the IRIS.
CAMERA ID OFF IRIS MANU... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
LEVEL ( 00) I RET
The [SHUTTER] menu is used to set the high speed electronic shutter and AUTO low speed shutter. The high speed electronic shutter can be used 7 different speeds and is commonly used for imaging fast moving objects. (NTSC: from 1/100 to 1/10K, PAL: from 1/120 to 1/10K ). The AUTO low speed electronic shutter can be any of 13 speeds from X2 to X256 and it slows the shutter speed to make images clearer in dark illumination. If you select an AUTO low speed, the shutter speed is automatically lowered depending on the darkness level.

CAMERA ID OFF IRIS ALC... SHUTTER AUTO X2 MOTION F.FAST WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
If you keep pressing the Left/Right SETUP switch, shutter speeds toggles in the following order:
OFF à AUTO X2 à AUTO X4 à AUTO X6 à AUTO X8 à AUTO X12
à AUTOX16 à AUTO X24 à AUTO X32 à AUTO X48 à AUTO X64 à AUTO X96 à AUTO X128 à AUTO X256 à OFF à 1/100(1/120) à 1/250 à 1/500 à 1/1000 à 1/2000 à 1/4000 à 1/10K
❚ AGC The AGC (Auto Gain Control) menu is used to set the AGC level of the camera. When the AGC is active, the camera automatically increases the sensitivity by amplifying the Video signal when the strength of the signal falls below the normal value.
CAMERA ID OFF IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
Only when [OFF] or a high speed shutter is selected in the [SHUTTER] menu, you can set the AGC level. You can select any of [OFF], [LOW], and [HIGH].

The [MOTION] menu is used to set the intensity of the camera AGC level for monitoring motions. This function is available only in AUTO low speed mode. You can select any of [S.SLOW], [SLOW], [NORM], [FAST], and [F.FAST] according to the AGC intensity level.
CAMERA ID OFF IRIS ALC... SHUTTER AUTO X2 MOTION F.FAST WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
To monitor very fast moving objects in dark illumination, select [F.FAST]. To monitor non-moving objects in dark illumination, select [S.SLOW].
The [WHITE BAL] menu is used to configure the white balance related settings for this camera.
CAMERA ID OFF IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT

9000K
8000K
7000K
6000K
5000K
4000K
3000K
2000K
1000K
To adjust the white balance, 4 different modes are provided as follows:

In the [FOCUS MODE] menu, the focus method can be set to AF(Auto Focus), MF(Manual Focus), or ONEAF(One Auto Focus).
CAMERA ID OFF IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
below. For such objects, focus manually. - High intensity objects or objects illuminated with low lighting - Objects shot through wet or dirty glass - Pictures that are a mixture of distant and nearby objects - White walls and other single-colour objects - Venetian blinds and other horizontally striped objects

[MOTION DET] menu is used to configure the motion detection related settings. If you press the SETUP switch when [ON…] is selected in the [MOTION DET] menu, the corresponding screen appears.
CAMERA ID OFF IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET ON... DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
TYPE 1 AREA 0* 1* 2* 3* DISPLAY ON SENSITIVITY L I H RET
You cannot change the setting for type 2 because it is prefixed with the full screen. In case of 1 and 3, you can set the motion detection area on your own.
Those 3 types are like the following:
The selected area is displayed with a box. The motion can be detected for the area only. You can manually set the motion detection area. You can use the Up/Down/Left/Right SETUP switch to set the size. To move to [POSITION], press the SETUP switch. After setting the position using the Up/Down/Left/Right SETUP switch, press the SETUP switch to move to the upper menu. To set the size and position for [AREA], select any of 0, 1, 2, and 3.


2. Label Type
The box-typed motion detection area is prefixed. The detected area is displayed with size and position changing. You cannot change [AREA] because it is displayed with [---].

The screen displays with small blocks. When a motion is detected in the selected blocks, the small blocks are displayed on the screen.
n [PRESET]: The whole screen becomes the motion detection area.
Up/Down/Left/Right SETUP switch to set the area. To erase the selected block, press the SETUP switch.


To select [RET], press UP key on the top block or press DOWN key on the bottom block and then press ENTER key to return a upper menu. In order to set the motion detection area on your own, you have to specify the size and location for the area setting. When [ON] is selected in [DISPLAY], the detected motion is displayed on the screen and the camera sends the Alarm Out signal. You can also assign the sensitivity for motion detection.
operating the PAN/TILT/ZOOM/FOCUS/IRIS functions. ※ Since the motion detecting function depends on the brightness
of selected area, it may dysfunction due to the different brightness between the background and object.
The [DAY/NIGHT] menu is used to configure the day and night related settings for this camera. This camera can turn the IR (Infrared) filter on or off.

CAMERA ID OFF IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT

DAY...
If you press the SETUP switch when the [DAY…] submenu is selected, the corresponding screen appears. You can set the values for [C-GAIN] when the DAY… submenu is selected. You can set the values for [AGC COLOR] and [AGC DETAIL] while the AGC menu is selected.
C-GAIN (7) I AGC COLOR ( 0) I AGC DETAIL (0) I RET
NIGHT...
If you press the SETUP switch when the [NIGHT…] submenu is selected, the corresponding screen appears.
COLOR/BW BW... RET

(COLOR)
BURST OFF RET
WHITE BAL ATW2 RET
Even in the Night mode, you can see colour images in bright illumination. Therefore, you can select any of [COLOR…] and [BW…]. In case of [COLOR…], you have to set the colour temperature for white balance. You can also specify the settings for red and blue colours on your own. In case of [BW...], the burst signals are output with the BW Composite Video signals, when the BURST is set to [ON]. And no burst signals are output when the BURST is set to [OFF].
This automatically converts the Day mode to the Night mode and vice versa depending on illumination. In low illumination, it removes the IR filtering function to raise the sensitivity. Otherwise, it activates the IR filtering function to lower the sensitivity. If you press the SETUP switch when the [AUTO…] submenu is selected, the corresponding screen appears.
LEVEL ( 0) I DAY NIGHT 2 S NIGHT DAY 5 S RET

For this function, you can specify the level for each conversion between [DAY] and [NIGHT].
This automatically converts the colour mode to the BW mode and vice versa by interfacing with an external sensor.
CAMERA ID OFF IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT EXT PRIVACY OFF SPECIAL ... PRESET ... EXIT QUIT
The [PRIVACY] menu is used to configure the privacy related settings for this camera. If you press the SETUP switch when [ON…] is selected in the [PRIVACY] menu, the corresponding screen appears.
CAMERA ID OFF IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY ON... SPECIAL ... PRESET ... EXIT QUIT
4 10 5 11
RET

<ZOOM/FOCUS> ... <SIZE>... <LOCATION>... COLOR ... EXIT QUIT
You can set 16 privacy zones in total. For configuration for 0 to 15 zones, you have to set the size, location, and colour.
※ For the safer privacy protection, select about 10 % more than the
actual area to hide when you set up the PRIVACY ZONE area. ※ The mosaic of the recorded images is set to be the PRIVACY
ZONE. The mosaic of the recorded images can not be recovered after recording.
The [SPECIAL] menu is used to configure the special settings for this camera. If you press the SETUP switch when […] is selected in the [SPECIAL] menu, the corresponding screen appears.
CAMERA ID OFF IRIS ALC... SHUTTER OFF AGC HIGH WHITE BAL ATW2 FOCUS MODE AF MOTION DET OFF DAY/NIGHT DAY... PRIVACY ON... SPECIAL ... PRESET ... EXIT QUIT
(SPECIAL) LANGUAGE ENGLISH VIDEO SET ... RS-485 ... ZOOM SPEED 4 DIGITAL ZOOM OFF DISPLAY ZOOM OFF SYSTEM INFO ... CTRL TYPE A V-SYNC INT RET

You can change the OSD language using the Left/Right SETUP switch.
The [VIDEO SET] menu is used to configure the privacy related set tings for this camera. If you press the SETUP switch when [ON…] is selected in the [PRIVACY] menu, the corresponding screen appears.
(SPECIAL) LANGUAGE ENGLISH VIDEO SET ... RS-485 ... ZOOM SPEED 4 DIGITAL ZOOM OFF DISPLAY ZOOM OFF SYSTEM INFO ... CTRL TYPE A V-SYNC INT RET
DNR OFF FLICKERLESS OFF REVERSE OFF DETAIL (2) I Y-LEVEL (0) I C-LEVEL (0) I POSI/NEGA + RET
DNR DNR(Digital Noise Reduction) function enables the picture to be reduced noise.
DNR ON FLICKERLESS OFF REVERSE OFF DETAIL (2) I Y-LEVEL (0) I C-LEVEL (0) I POSI/NEGA + RET

FLICKERLESS When this is set to [ON], the shutter speed is set to 1/100 sec (for NTSC) or 1/120 sec (for PAL) to prevent from flickering by the discordance between vertical synchronization frequency and on-and-off frequency of the light.
REVERSE It is used to mirror video signals horizontally, vertically, or both.
DETAIL It is used to control the horizontal or vertical distinction.
Y-LEVEL It is used to set the levels for the Sync signal and the entire brightness signal of the video signal.
C-LEVEL It is used to set the levels for the Burst signal and the entire colour signal of the video signal.
POSI/NEGA It is used to output as it is, or mirror the video brightness signal.
If you press the SETUP switch when [...] is selected in the [RS-485] menu, the corresponding screen appears.
(SPECIAL) LANGUAGE ENGLISH VIDEO SET ... RS-485 ... ZOOM SPEED 4 DIGITAL ZOOM OFF DISPLAY ZOOM OFF SYSTEM INFO ... CTRL TYPE A V-SYNC INT RET
PROTOCOL SAMSUNG BAUD RATE 9600 ADDRESS 0 RET
You can set the PROTOCOL, BAUD RATE, and ADDRESS (range: 0 to 255) for this communication.

(SPECIAL) LANGUAGE ENGLISH VIDEO SET ... RS-485 ... ZOOM SPEED 4 DIGITAL ZOOM OFF DISPLAY ZOOM OFF SYSTEM INFO ... CTRL TYPE A V-SYNC INT RET
Use the Left/Right SETUP switch in the [ZOOM SPEED] menu to select the speed. 1 : Slowest speed 2 : Low speed 3 : High speed 4 : Fastest speed
You may set up the digital zoom magnification ratio in the [DIGITAL ZOOM] menu. The magnification ratio ranges from [OFF] to 16 times. If you set Digital Zoom of the camera to maximum 16 times, the mode will become the 32 time optical zoom and you will be able to enlarge a subject by maximum 512 times. Use the Left/Right SETUP switch to select a magnification ratio in the [DIGITAL ZOOM] menu.
(SPECIAL) LANGUAGE ENGLISH VIDEO SET ... RS-485 ... ZOOM SPEED 4 DIGITAL ZOOM X16 DISPLAY ZOOM OFF SYSTEM INFO ... CTRL TYPE A V-SYNC INT RET

In the [DISPLAY ZOOM] menu, you can display the ZOOM scale on the screen.
(SPECIAL) LANGUAGE ENGLISH VIDEO SET ... RS-485 ... ZOOM SPEED 4 DIGITAL ZOOM OFF DISPLAY ZOOM ON SYSTEM INFO ... CTRL TYPE A V-SYNC INT RET
This [SYSTEM INFO] menu is used to check the system-related in formation. If you press the SETUP switch when the [SYSTEM INFO] menu is selected, the corresponding setup screen appears.
(SPECIAL) LANGUAGE ENGLISH VIDEO SET ... RS-485 ... ZOOM SPEED 4 DIGITAL ZOOM OFF DISPLAY ZOOM OFF SYSTEM INFO ... CTRL TYPE A V-SYNC INT RET
ROM VER 1.000 EEP VER 1.000 PROTOCOL SAMSUNG ADDRESS 0 COMM. TYPE RS-485, HALF BAUD RATE 9600 SERIAL NO. 000000000000000 RET
You can find the system information about ROM version, EEP version, protocol, address, type, baudrate, and serial number.
![Page 35 of the Samsung C4333(P) user manual — Note - In case of [LINE], SCC-C4333(P)/SCC-C4335(P) doesn’t support](/cdn/reader/fb/fbf698f0e7bd54a948fd0f4c6ee7156bceedcf203f18d1e0520e68256da16f2c/images/page-35.webp?w=400)
By inputting the wire remote port, you may set up the A, B, C or D mode.

V-SYNC You can select a vertical synchronization mode between [INT] and [LINE]. In case of [INT], the camera uses the inside crystal oscillator for synchronization. In case of [LINE], the camera uses the frequency of the external power for synchronization.
for DC 12V, which [-- -] is displayed. - SCC-C4233(P)/C4235(P) does not support for V-SYNC function.

Select the [PRESET] menu and press the SETUP switch and the [PRESET MAP] submenu screen will appear.
PRESET NO. 0
4 9 14 19 24 29 RET HOME RETURN OFF
1 6 11 16 21 26 31
2 7 12 17 22 27
3 8 13 18 23 28
POSITION SET ... PRESET ID ON...
EXIT QUIT
Select the PRESET number and press the SETUP switch and the
above screen will appear.
POSITION SET It is used to memorize the position of ZOOM or FOCUS.
PRESET ID It is used to designate the ID on the basis of the PRESET position as the [CAMERA ID].
HOME RETURN Time Setup OFF 1MIN 2MIN 3~60MIN 2 HOUR 3~12 HOUR

Product type CCTV Camera
SCC-C4235(P) : 5W
SCC-C4333(P) : 5W
SCC-C4335(P) : 5.5W
Horizontal: NTSC 15,734Hz(INT)/15,750Hz(LL) PAL 15,625Hz(INT)/15,625Hz(LL) Vertical: NTSC 59.94Hz(INT)/60Hz(LL) PAL 50Hz(INT)/50Hz(LL)
INT/Line Lock (SCC-C4233(P)/C4235(P) does not support for Line Lock function.)
Resolution 540(COLOR)/570(BW) TV Lines
S/N Ratio Approx. 50dB
Power consumption · Scanning line frequency · Synchronization mode


White Balance ATW1/ATW2/AWC/MANUAL Mode (3200°K, 5600°K, R/B Gain adjustment)

(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.





I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.