Manuale d’uso / di manutenzione del prodotto RSS-1050 del fabbricante Royal Sovereign
Vai alla pagina of 27
Royal Sovereign LAMINATORS OWNER'S MANUAL RSS-1200,1050 ,685 PLEASE READ AND SAVE INSTRUCTIONS. - 1 -.
MEMO ---------------------------------------------------------------------------------------------- - 27 1.HOT FILM ----------------------------------------------------------------------------------------- 2.
5. Do not operate machine for any other purposes than its intended use. 6. Do not operate machine if electrical plug or power cord is damaged. 8. This machine is intended for indoor use only.
Remote control device allows for control of the machine from the front or rear. thickness of film and materials to be laminated. Yes Yes 1200(mm) 47.2(in) 1050(mm) 41.3(in) 685(mm) 27(in) Yes Yes 22 1 Yes Film Alignment Cutter-Cross Foot-Switch AC 100~120/ 200~240V 50~60Hz 6m/min (19.
1. FILM-UPPER 8. FOOT SWITCH 2. FILM-LOWER 9. REMOTE CONTROL SWITCH 3. TAKE-UP (ASS'Y-TAKE-UP) 10 . CONTROL PANEL 4. IDLER BAR (UPPER) 11 . PRESSURE LEVER 5. TABLE-FRONT 12 . TENSION CONTROL KNOB 6. SHOE-HEATER,UPPER 13 . ALIGNMENT KNOB 7. ASS'Y-STAND 14 .
1. HOW TO CONTROL TENSION 2. HOW TO ADJUST ALIGNMEN T Location control device is used when the edges of the lamination are unjustified. As the drawing shows, when the alignment knob is turned clockwise, the upper film is to left. Once proper alignment is reached, turn the Locking Nut tight against the Alignment knob so the adjustment is set.
1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft. 3. Like picture 2 and 3, insert core into the right side of upper/lower film.
1. HOT FILM 10. After checking the status of lamination, Place the pressure lever at the proper lamination mode. 6. Allow some of the film with melted resin to stick to the Guiding Paper. 7. Repeat step 5 with lower roll film then stick it to the Guiding Paper.
2. COLD FILM 1. Take out the guiding table. 2. Put the shaft of roll film in each hole exactly. 3. Set the pressure lever to the proper lamination mode.(1mm/5mm/10~13mm) 4. Pull the film around the idler bar to the Anti-wrinkle device. 5. Put the paper back of the film to the bobbin at take-up bar to rewind the paper back.
1. For setting, pull the pressure lever out and turn the lever to following the indication. 5. Laminating : Mode that you can do laminate 25mic(1mil) to 250mic(10mil) 2. 10~13mm Board : Mode that you can laminate 10~13mm(1/3" to 1/2") 3. 5mm Board : Mode that you can laminate 5mm(1/4") hard board 4.
You can manipulate speed and temperature with the LCD controller. We designed the LCD panel for user convenience by adopting memory working condition. INSTRUCTIONS FOR CONTROL PANEL ***Terms*** LCD DI.
1.LCD WINDOW 1. Initial display status. It displays the last working condition when the power is turned on. 2. 3. Indicates to wait till blinking stops. Current temperature is higher or lower than the preset temperature. 4. Saving electricity status. 5.
2. FUNCTIONS OF BUTTONS : Upper shoe temperature controller : Lower shoe temperature controller : Speed controller : Choose memorized working condition : ① Increase temperature ② Increase s p eed .
3.HOW TO USE BUTTONS 1. Temperature available range from 0°C (32°F) to 160°C (320°F). 2. Set temperature of upper shoe. Press upper button then you will see the LCD is blinking 6 times. Before blinking is finished, press 3. Set temperature of lower shoe.
1) Memorize working condition 1.Operator can memorize 9 working conditions. 2.Each time you press the button, buzzer is ringing. 3.find the condition number you are willing to memorize working condition by pressing button. 4.When you finish setting upper/lower temperature and speed, you can press the memory button.
1.This function allows you to check the current temperature on the shoes. 2.Press then temperature is shown on the display while display is blinking. 3.It shows current temperature 5 times then returns to temperature which the operator has set. 4.It shows "LO" when the temperature is 40° c (104°F) or below.
on the screen and STND-BY mode is set at 80 ℃ . 2. When machine is in mode, machine condition wouldn’t work. Press the button and it will revert to the previous working. 3. When the machine runs, you can’t change it to the the machine to the mode.
6. It is ready when the LCD window shows 9.Push 11. Push 4. Set pressure lever to "Laminating" position. 5. Increase temperature of the hot shoe. If the temperature is memorized for the button to choose the correct location. 7. To set the film tension properly, please use the Tension Adjustment Knob while 3.
SPEED 1 1.0m(3.3ft) SPEED 2 1.6m(5.2ft) SPEED 3 2.0m(6.6ft) SPEED 4 2.2m(7.2ft) SPEED 5 2.6m(8.5ft) SPEED 6 3.3m(10.8ft) SPEED 7 4.3m(14.1ft) SPEED 8 5.2m(17.1ft) SPEED 9 6.0m(19.7ft) almost no film tension. There might be the possibility for difference to the above numbers due to the change of voltage or adjustment of tension.
1 2 3 4 5 6 7 8 *NOTE IF the surrounding conditions are different, the adjustment is necessary to be controlled a lttle. Paper Thickness ***Temperature/Speed adjustment guide*** Speed Film NO Remarks .
+ 7. Set document on the table. You should allow at least 5mm(1/4”) space on each side for perfect laminations 8. Turn the switch “Run” and "take up motor " at the same time. The liner and film wii be 11. Turn off the power switch. 2. Pull COLD film, and fix it so that backside protecting paper can be wound on the take- u 5.
1. It is convenient to use the remote control in the back of machine while laminating. 2. It is also convenient if you use Foot Switch while laminating HARD BOARD. 3. "RUN", "STOP", "REV" buttons on Remote Control have same functions with the ones on Control Panel.
2. Slitters 1.This machines has two vertical cutters (slitters) 2. For successive lamination, it is easy to cut vertically. 3.Fix the cutter at the point to be cut, on the left and right. (Turn the screw counter clock wise to loosen the slitter, and slide it to the point to be cut.
2. Prevent children from accessing the machine. Extreme Heat Will Cause Injury 4.Make certain that the machine is connecterd to an adequate power source. 1.Do NOT Allow the machine to run with only one roll of film installed. The melted resin will adhere to one roller and ruin future laminations.
Rollers do not operate 1. Power cord may not be plugged 1. Check the power cord after press RUN in. 2. Check the switch is on button. 2. Power switch is at OFF mode. 3. Check the emergency switch 3. Emergency switch may be at is off ON mode. 4. Release STND-BY switch by 4.
1. DURATION OF LIMITED WARRANTY One (1) year from the date of "Buyer's" receipt of delivery. 2. INSPECTION and CLAIMS It is the "Buyers" responsibility to inspect all merchandise immediately upon receipt. Any claims must be submitted to the "Seller" in writing, along with adequate examples (samples, photos, etc.
MEMO - 27 -.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Royal Sovereign RSS-1050 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Royal Sovereign RSS-1050 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Royal Sovereign RSS-1050 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Royal Sovereign RSS-1050 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Royal Sovereign RSS-1050, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Royal Sovereign RSS-1050.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Royal Sovereign RSS-1050. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Royal Sovereign RSS-1050 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
