Manuale d’uso / di manutenzione del prodotto RNX-G300EXLX del fabbricante Rosewill
Vai alla pagina of 111
Wir eless Adapter RNX-G300EX/LX User Manual.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 1 - CONTENT Introduction ................................................................................................................... .................... - 2 - Specifications ..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 2 - INTRODUCTION Thank you for purchasing Wireless LAN PCI Car d. Wireless car d is a perfect combination pr oduct of performance and cost-eff ectiveness. It is sincerely h oped that you can enjoy the wir eless world thr o ugh this solidly profiled wireless car d.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 3 - SPECIFICA TIONS Interface PCI Standard 802.11b, 802.11g OS support 98SE, WinME, Win2000, WinXP32, WinXP64, Vista32, Vista64 Data rate 1,2,5.5, 11,6,8,12,18,24,36,48 , 54Mbps, depends on the wireless mode Frequency band BG:2.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 4 - INST ALLA TION HARDWARE INST ALLA TION 1. Turn off your PC and remove the cover. 2. Insert the RNX-G30 0EX/ LX to an available PCI slot fi rmly. 3. Secure this card to the rear of the computer chassis 4.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 5 - SOFTWARE INST ALLA TION (FOR ALL WINDOWS OS) After hardware installation complete, system will detect new hardware automatically as below: Found New Hard ware Wizard window pop s up, click Cancel .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 6 - Click Driver Installation Click I accept the term of the license agreement ,then click Next icon.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 7 - Click Ralink Configuration T oo l , then click Next icon. Click Optimize for WiFi mode s, then click Next icon.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 8 - Click Install icon. Click Finish icon..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 9 - SOFTWA RE UNINST ALL Click My Computer icon, then click Add or Remove Pr ogram icon, and then click Ralink Wireless LAN icon and then click Remove icon. Click Y es, I want to restart my compu ter now icon, and then Finish icon.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 10 - RALINK WIRELESS UTILITY ( RAUI ) OR WINDOWS ZERO CONFIGURA TION ( WZC ) In windows XP , it pr ovides wireless configuration utility named "Windows Zero configura tion" which pr ovides basic configuration function for Ra link Wireless NIC.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 11 - Figure 1-3 RaUI status with WZC active When activating WZC, there are couple dif ference on RaUI status compared to that with out WZC running. A. Profile button will be gray , pr ofile function is r emoved since the NIC is contr olled by WZC B.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 12 - USE WZC TO CONFIGURE WIRELESS NIC A. If connection is lost or not connected, th e status prompt as Figur e 1-4 will pop up. Figure 1-4 status prompt of no connection B. Right-click the network conn ection icon in task bar .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 13 - Figure 1-6 Wir eless Network Connection D. Select intended AP and click "Connect" s hown as Figure 1-7.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 14 - Figure 1-7 Select intended AP : AP1, then click "Connect".
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 15 - Figure 1-8 Connect AP : AP1 successfully E. If you want to modify information about AP , click "Change advanced settings" shown as Figure 1-9. Then choose "Wireless Networks" label shown as Figur e 1-10.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 16 - Figure 1-9 Click "Change adva nced settings" Figure 1-10 Choose "Wir eless Networks" label.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 17 - F . Click "Properties" shown as Figur e 1-11. Then click "OK" button. Figure 1-11 AP's pr operties G. After filling appropriate value, click "OK" bu tton.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 18 - Figure 1-13 Show connection status by using WZC to do connection.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 19 - ST ART RAUI When starting RaUI, system will connect to the AP with best signal str ength without setting profile or ma tching pr ofile setting . When starting RaUI, it will issue a scan command to wir eless NI C.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 20 - A. Button Section : Include Profile page, Net work page, Ad vanced page, Statistics page, WMM page, WPS page, About button, Radio On/Off button and Help button. Figure 2-1-2 Button section Figure 2-1-3 Move to the left Figure 2-1-4 Move to the right B.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 21 - Figure 2-1-6 Network page Figure 2-1-7 Advance page.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 22 - Figure 2-1-8 Statistics page Figure 2-1-9 WMM page.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 23 - Figure 2-1-10 WPS page Figure 2-1-11 About page C. Status Section : Include Link Status, Authe ntication Status, AP's informa tion, Configuration and retrying the connection when authentication is f ailed.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 24 - Figure 2-1-12 Link Status Figure 2-1- 13 Authentication Status Figure 2-1-14 AP's Information.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 25 - Figure 2- 1-15 Retry the connection Figure 2-1-16 Configuration At the mean time of starting RaUI, ther e is also a small Ra link icon appears within windows taskbar as Figur e 2-1-15.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 26 - Besides, the small icon will change color to r eflect current wir eless network connection status. The status indicates as follow: : Indicate Connected and Signal Str ength is Good.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 27 - ICONS AND BUTTONS : Indicate connection is succes sful on curr ently activated pr ofile. Indicate connection is failed on curr ently activated pr ofile. Indicate network type is infrastructure mode.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 28 - ADD/EDIT PROFILE There ar e thr ee methods to open Profile Editor f orm. A. Y ou ca n open it from "Add to Pr ofile" button in Site Surve y function. B. Y ou ca n open it from "Add" button in Profile function.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 29 - D. Network T ype : There ar e two types, infrastructure and 802.11 Ad-hoc mode . Under Ad- hoc mode, user can also choose the preamble t ype, the available preambl e type includes auto and long.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 30 - EXAMPLE TO ADD PROFILE IN PROFILE A. Click Add in Profile function..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 31 - B. Add Profile page will pop u p..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 32 - C. Change prof ile name to what you want to connect. Pull down the ssid and select one intended AP .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 33 - D. Then, you can see the pr ofile which you set appear in th e pr ofile list. Click "Activate" .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 34 - NETWORK Under the Network function, system will displa y the information of surrounding APs from last scan result. List informations include SSID, BSSID, Signal, Chan nel, Encryption algorithm, Authentication and Network type a s Figure 2-3-1-1 shown.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 35 - ICONS AND BUTTONS : Indicate connection is succes sful. Indicate network type is infrastructure mode. Indicate network type is Ad-hoc mode. Indicate security-enabled wir eless network.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 36 - CONNECTED NETWORK : A. When RaUI first ran, it will select the best AP to connect automatically . B. If user wants to connect to other AP . He can click "Conne ct" button for the intended AP to make connection.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 37 - A-1.General information conta in AP's ssid, MAC addr ess, authentication type, encryption type, channel, network type, beacon interval, signal str ength and support ed rates. It shows as Figur e 2-3-1-2.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 38 - A-2. WPS information contain authen ticatio n type, encryption type, config methods, devi ce password id , selected registrar , state, version, AP setup locked, UUID-E and RF ban ds as Figur e 2-3-1-3.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 39 - Figure 2-3-1-3 WPS information about AP's detail informati on.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 40 - A-3. CCX information contains CCKM, Cmic and Ckip information. It shows as Figure 2-3-1-4.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 41 - A-4. 802.11n information cont ains some related 802.11n information. It shows as Figure 2-3-1-5.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 42 - EXAMPLE ON ADDING PROFILE IN NETWORK A. Select the intended network from AP list in Network function.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 43 - B. Click "Add to Pr ofile"..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 44 - C. System will pop up Add Profile windows. Y ou can change profile name which you like most.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 45 - D. Then, you can see the pr ofile which you set appear in the pr ofile list. Click "Activate" .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 46 - ADV ANCED Figure 2-4 shows Advance function of RaUI. Figure 2-4 Advance function A. Wireless mode : Select wir e less mode. 802.11 B only , 80 2.11 A only , 802.11 B/G mix, 802.11 B/G/N mix, 802.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 47 - ICONS AND BUTTONS: Show the information of Status Section. Hide the information of Status Section. ST A TISTICS Statistics page displays the deta il counter information base d on 802.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 48 - C. RTS Frames Su ccessfully Receive CTS : Successfully r eceive CTS after sending RTS fr ame. D. RTS Frames Fail T o Receive CTS : Failed to receive CTS after sending RTS. E. Frames Retransmitted Successf ully : Successfully r etransmitted frames numbers.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 49 - WMM Figure 2-6-1 shows WMM function of RaUI. It involves "WMM Enable", "WMM - Power Save Enable" and DL S setup. The intr oduction indicates as follow : Figure 2-6-1 WMM function A.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 50 - EXAMPLE TO CONFIGURE TO ENABLE DLS (DIRECT LINK SETUP) A. Click "Direct Link Setup Enable".
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 51 - B. Change to "Network" function. And add a AP that supports DL S features to a Profile. The result will look like the below figure in Pr ofile page. The setting of DLS indicates as follow : A.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 52 - B. Timeout V alue repr esents that it disconnect automatically after some s econds. The value is integer . The integer must be between 0~65535. It represents that it always connects if the va lue is zer o.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 53 - C. Click "Apply" button. The result will look like the below figure. Describe "DLS Status" as follow : A. As the up figur e, after configuring DLS successfully , show MAC addres s of the opposite side and Timeout V alue of setting in "DLS Status".
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 54 - B-2. Double click. And the r esult will look like the below figure. C. Disconnect Dir ect Link Setup as follow : C-1.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 55 - C-2. Click "T ear Down" button. The result will look like the below figure.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 56 - EXAMPLE TO CONFIGURE TO ENABLE WI-FI MUL TI-MEDIA If you want to use "WMM-Power Sav e" or "Direct L ink" you must enable WMM. The set ting method of enabling WMM indicates as follows: A.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 57 - B. Change to "Network" function. And add a AP that supports WMM features to a Profile.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 58 - EXAMPLE TO CONFIGURE TO ENABLE WMM POWER SA VE A. Click "WMM-Power Save Enable". B. Please select which ACs you want to enable. The setting of en abling WMM-Power Save is successfully .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 59 - WPS Figure 2-7-1 shows WPS function of RaUI . The intr oduction indicates as follow: Figure 2-7-1 WPS function.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 60 - A. WPS Configuration : The primary goal of Wi-Fi Protected Se tup (Wi-Fi Simple Configuration) is to simplify the security setup and management of Wi-Fi networks.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 61 - WPS INFORMA TI ON ON AP WPS information contain au thentication type , encryption type, config meth ods, device password id, s elected registrar , state, version, AP setup locked, UUID-E and RF band s.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 62 - A. Authentication T ype : There ar e three type of authentication modes supported by RaCon fig. They are open , Shared , WP A-PSK and WP A system. B. Encryption T ype : For open and shar ed authentication mode , the s election of encryption type ar e None and WEP .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 63 - EXAMPLE TO ADD TO REGISTRAR USING PIN ME THOD The user obtains a device p assword (PIN Code) fr om the ST A and enters the password in to the Registrar . Both the Enr ollee and the Registrar use PIN Config method fo r the confi guration setup.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 64 - B. Click "Rescan" button to update available WPS APs. C. Select an AP (SSID/BSSID) that ST A will join to.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 65 - D. Click "PIN" button to start PIN connection. F . Enter PIN Code of ST A into the Regi strar when prompted by the Registrar . *Allow of an exchange betw een Step 4 and Step 5.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 66 - H. Configured and got one or multiple cr edential(s). I . Then connect successfully .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 67 - J. Click "Detail" button. K. Y ou will look like the below figure. *If Credential#1 is r eliable and present, syst em will connect with Credential#1. On the contrary , system will auto rotate to the next existed cr edential.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 68 - A. Asuccessful PIN Configuration : Start PIN connection - SSID ~> Begin associating to WPS AP ~> Associated to WPS AP ~>.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 69 - EXAMPLE TO ADD TO REGISTRAR USING PBC ME THOD The PBC method requir es the user to press a PBC button on both the Enrollee and the Registrar within a two-minute interval called the Walk Time.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 70 - B. Click PBC to start PBC connection. C. Push PBC on AP . *Allow of an exchange betw een Step 2 and Step 3.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 71 - E. When finding only one AP , join it. F . Check WPS Information on available WPS APs.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 72 - G. Configur ed and got one or multiple creden tial(s). H. Then connect successfu lly .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 73 - A. A successful PBC Configuration : Start PBC connection ~> Scanning AP ~> Begin associating to WPS AP ~> Associated t o.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 74 - EXAMPLE TO CONFIGURE A NETWORK/ AP USING PIN OR PBC METHOD A o to the box of Config Mode and select Registrar .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 75 - B. Enter "Detail" of th e credential and ch ange configurations (SSID, Au thentication, Encryption and Key) manually if need. C. If PIN configuration setup, enter Pin Code r ead from your Enr ollee.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 76 - Describe "WPS Status Bar" - "PIN - xxx" as follow : A successful PIN Configuratio n : Start PIN connection - .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 77 - LINK ST A TUS Figure 2-9 is the link status page, it disp lays t he detail information curr ent connection. Figure 2-9 Link Status function A. Status : Current connection status. If no connection, if will show Disconnected.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 78 - AUTH. ENCR Y . SETTING - WEP/TKIP/AES Auth. Encry . Setting, shown a s Figure 3-1. Figure 3-1 Auth. Encry . Setting A. Authentication T ype : There ar e 7 type of authentication modes supported by R aUI.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 79 - 802.1X SETTING 802.1x is a authentication for "WP A" and "WP A2" certificate to serve r . AUTHENTICA TION TYPE : A. PEAP : Protect Extensible Authentication Protocol.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 80 - AUTHENTICA TION : A. Protocol : T unnel pr otocol, List informatio n include "EAP-MSCHAP v2", "EAP-TLS/Smart ca rd", "Generic T oken Card", "CHAP", "MS-CHAP", "MS-CHAP-V2", "P AP" and "EAP- MD5".
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 81 - - EAP F AST - A. Allow unauthenticated provision mode : Duri ng the P AC can be provisioned (distributed one time) to the client automatically .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 82 - EXAMPLE TO RECONNECT 802.1X AUTHENTICA TED CONNECTION AFTER 802.1X AUTHENTICA TED CONNECTION IS F AILED IN PROFILE There ar e two situatio ns to be able to reconnect 802.1x authenticated connection and authenticat e successfully after 802.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 83 - D. Click "OK" button. If it conn ected successfully , th e result will look like the below figur e.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 84 - When occurring "Timeout" : A. Authentication type chooses "PEAP", key identity into wpatest2. T unnel Protocol is "EAP-MSCHAP-v2, and tunnel identity is wpatest2 and tunnel password is test2.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 85 - c. If it connected succe ssfully , the result will look like the below figur e..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 86 - EXAMPLE TO CONFIGURE CONNECTION WITH WEP ON A. Select AP with WEP encry ption and click "Connect" button.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 87 - B . Auth. Encry . function pop up..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 88 - C . Enter 1234567890 at Key#1 whic h is same as our intended AP's setting..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 89 - D. Click "OK" button. The result will look like the below figure..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 90 - EXAMPLE TO CONFIGURE CONNECTION WITH WP A-PSK A. Select the AP with WP A-PSK authenti cation mode and click "Con nect" button.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 91 - B. Auth. Encry . function pop up. (If AP setup security to Both (TKIP + AES), system defines is AES that security is sever ely .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 92 - C. Authentication T ype is WP A-PSK. Select corr ect encryption (TKIP or AES). Enter WP A Pr e-Shared Key secret as 12345678.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 93 - D. Click "OK" button. Be car eful, if the WP A Pre-Shared Key en tered is not correct, even th ough the AP can be connected, but you won’ t be able to exchange any data frames .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 94 - EXAMPLE TO CONFIGURE CONNECTION WITH WP A A. Select AP with WP A authentication mode and click "Connect" button.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 95 - B. Auth. Encry . function pop up. (If AP setup security to Both (TKIP + AES), system defines is AES that security is severely .
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 96 - C. Click "8021X" button and 802.1x setting page will pop up..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 97 - D. Authentication type and setting method : PEAP : A. Authentication type chooses PEAP , key identity into wpatest2. Protocol chooses EAP- MSCHAP v2 for tunnel authentication, tunnel ide ntity is wpatest2 and tunnel password is test2.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 98 - B. Click OK. The r esult will look like the below figure. *If you want to disconnect, please c lick cancel button in Authentication S tatus function. *In Profile function, show "Profile Name" option only in adding AP to Profile function.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 99 - C. If it connected succe ssfully , the result will look like the below figure..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 100 - TLS / Smart Card : A. Authentication type chooses TLS / Smart Car d, TLS only need identity that is wpatest2 for server authentication.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 101 - B. TLS must use client certification. Click "Client Certification" button and choose a certification for server au thentication.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 102 - C. Click "OK" button. The result will look like the below figur e. *If you want to disconnect, please c lick cancel button in Authentication S tatus function. *In Profile function, show "Profile Name" option only in adding AP to Profile function.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 103 - D. If it connected succe ssfully , the result will look like the below figur e.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 104 - TTLS : A. Authentication type chooses TTLS, ide ntity is wpatest2. Protocol chooses CHAP for tunnel authentication, tunnel identity is wpatest2 and tunnel password is test2. Those setting are same as our intended AP's setting.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 105 - B. Click "OK" button. The result will look like the below figur e. *If you want to disconnect, please c lick cancel button in Authentication S tatus function. *In Profile function, show "Profile Name" option only in adding AP to Profile function.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 106 - C. If it connected succe ssfully , the result will look like the below figure..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 107 - EAP-F AST : A. Authentication type choose s EAP-F AST , key identity into wp atest2; key domain name into blank space. T unnel Pr otocol only supported "Generic T oken Card" now , and tunnel identity is wpatest2 and tunnel password is test2.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 108 - B. Click "OK" button. The result will look like the below figur e..
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 109 - C. If it connected succe ssfully , the result will look like the below figure. *If you want to disconnect, please c lick cancel button in Authentication S tatus function. *In Profile function, show "Profile Name" option only in adding AP to Profile function.
Wireless Adap ter R N X - G 3 0 0 E X / L X U s e r M a n u a l - 110 - ACKNOWLEDGEMENTS The above setting is test platf orm by RaLink technology corp. User can set the function in accordance with A.P . Acknowledgements: "This product includes software developed by MDC and its li censors.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Rosewill RNX-G300EXLX è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Rosewill RNX-G300EXLX - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Rosewill RNX-G300EXLX imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Rosewill RNX-G300EXLX ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Rosewill RNX-G300EXLX, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Rosewill RNX-G300EXLX.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Rosewill RNX-G300EXLX. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Rosewill RNX-G300EXLX insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
