Manuale d’uso / di manutenzione del prodotto CrystalView Plus del fabbricante Rose electronic
Vai alla pagina of 48
CrystalView Plus ENHANCED CAT5 KVM EXTENDER 10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933 - 7673 Internet: WWW.ROSE.COM INSTALLATION AND OPERATIONS MANUAL.
LIMITED WARRANTY Copyright Rose Electronics 2004. All rights reserved. No part of thi s manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and recording, without the prior written permission of Rose Electronics.
FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO - FREQUENCY INTERFERENCE STAT EMENTS This equipment generates, uses and can radiate radio fr.
EUROPEAN UNION DECLARATION OF CONFORMITY ACCORDING TO COUNCIL DIRECTIVE 89/336EEC & 73/23EEC This equipment is in conformity with the protection requirements of the following Council Directives: T.
TABLE OF CONTENT S Contents Disclaimer ...................................................................................... 1 System introduction ........................................................................ 1 Features ...................
Figures Figure 1. Single Video (Local models) ............................................ 4 Figure 2. single Video (Remote models) ......................................... 5 Figure 3. Dual video (Local models) .......................................
INTRODUCTION CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 1 Disclaimer While every precaution has been taken in the preparation of this manual, the m anufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein.
2 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Features n Available in single, dual, and quad video models n Extend a KVM station from a CPU using a single CAT - x cable . (Up to 6 50 feet at resolutions of 1600 x 1200 @ 60Hz, 1,000 feet for the resolutions of 1280 x 1024 @ 75Hz.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 3 Compatibility Computers PCs with standard PS/2 keyboards and PS/2 mice Monitors VGA to UXGA HV, Composite, Sync - on - green, Keyboards PS/2 types of keyboard.
MODELS 4 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Single video Local models Front view Rear view Rear view with serial/audio Rear view with local access Rear view with local access & serial/audio Figure 1 .
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 5 Single video Remote models Front view Rear view Rear view with serial/audio Figure 2 . single Video (Remote models) Connectors: Front § RJ45 CATx cable connection (front panel) Rear Remote § HD15F KVM video connection.
6 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Dual video local models Front view Rear view Rear view with serial/audio Figure 3 . Dual video (Local models) Connectors: Front § RJ45 (2) CATx c.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 7 Dual video remote models Front view Rear view Rear view with serial/audio Figure 4 . Dual video (Remote models) Connectors: Front § RJ45 (2) CATx.
8 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Quad video remote models Front view Rear view Rear view with serial/ audio Figure 5 . Quad video (Remote models) Connectors: Front § RJ45 (4) CAT.
CABLES CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 9 Cables CrystalView Plus Local Unit to CPU cable A CPU adapter cable i s used to connect from the Local Unit to a CPUs keyboard, video monitor and mouse ports.
10 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Serial cable To connect the Local Unit to the CPUs DB9 serial port, you can use a standard DB9MF serial 1:1 (DTE - DCE) cable. The Remote Units “SERIAL” port is wired as DTE (the same as the CPUs serial port).
INSTALLATION CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 11 Installation Please refer to the safety section first before proceeding with any installation or configuration of the CrystalView Plus. Installation of the CrystalView Plus consists of three easy steps.
12 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Connecting the cables Figure 6 . Single video cabl ing Local uni t to CPU cabling (Refer to Figure 1 and Figure 6 ) The keyboard, video, and mouse ports on the CPU are connected to the keyboard, video, and mouse ports on the CrystalView plus using an appropr iate CPU adapter cable.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 13 Remote uni t to KVM station cab ling (Refer to Figure 2 and Figure 6 ) On the remote unit, the KVM station’s keyboard, monitor, and mouse cables are connected directly to the CrystalView Plus keyboard, monitor, and mouse connectors.
14 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Dual Video cabling (Refer to Figure 3 & Figure 7 ) The CrystalView Plus dual video models provide total access to one PC and the ability to view a second video source from an extended distance over a pair of CATx cables.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 15 Remote uni t to KVM station cabling (Refer to Figure 4 and Figure 7 ) On the remote unit, the KVM station’s keyboard, monitor, and mouse cables are connected directly to the CrystalView Plus keyboa rd, monitor, and mouse connectors.
16 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Quad Video Remote Unit cab ling (Refer to Figure 3 and Figure 8 ) Figure 8 . Quad video cabling For Quad video systems, the local units consist of two dual video units. Connect these units as described in the dual video section.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 17 Connecting to a Rose KVM switch The CrystalView Plus can further enhance your system by connecting t he local unit to a Rose KVM switch. This provides remote access to as many as 1,000 computers (depending on the type of KVM switch and topology configuration).
KEYBOARD COMMANDS 18 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Keyboard commands Note: Use only the numeric keys above the keyboard to initiate the keyboard commands from the remote unit.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 19 Keyboard command descriptions Command mode – [ L - Ctrl ] + [ L - Shift ] + [F10] Entering the command mode sends the remote units keyboard instructions to the CrystalView Plus instead of the connected co mputer.
20 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Reset EQ & Delay values – [L - Ctrl] + [Home] Issuing this command resets the LF and HF equalization and the red, green, and blue delay values for the selected channel.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 21 Toggle RED delay – [L - Ctrl] + [ R ] Each time this command is issued, the RED video component delay is toggled between 0 and 19ns. Toggle GREEN delay – [L - Ctrl] + [ G ] Each time this command is issued, the GREEN video component delay is toggled be tween 0 and 19ns.
22 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Reset keyboard and mouse – [F1] Pressing the [F1] key while in the command mode will reset the keyboard and mouse, and then exit the command m ode. Use this command if the keyboard or mouse lock up or the mouse does not initialize properly.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 23 Reset the local keyboard and mouse If the lo cal keyboard or mouse locks up, you can reset them by issuing the reset command.
VIDEO ADJUSTMENTS 24 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Adjusting the video All video adjustments are performed from the remote unit. Make sure all connections are in place and the video from the computer(s) connected to the local unit are powered up and operating properly.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 25 Figure 11 . Video Test Card To begin adjusting the LF and HF equalizatio n, display the text card as shown in Figure 11 .
26 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL In summary, adjusting the video consists of: 1. Enter the Command Mode 2. Select the video channel to adjust 3. Display the test card or a created straight line graphic tha t is equally divided into three color parts, RED, GREEN, and BLUE 4.
OPE RATING INSTRUCTIONS CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 27 Operating instructions - All units Once the Remote and Local Units ar e connected and configured, the Remote KVM station’s keyboard, video monitor and mouse will function as if it were directly connected to the CPU.
TROUBLESHOOTING 28 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Troubleshooting The troubleshooting section is used as a guide to understan ding the capabilities of the CrystalView Plus and for general troubleshooting.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 29 Only video is required, but no picture appears. n The probable cause is that power to the Local Unit is not applied. The Local Unit obtains its power from the CPUs keyboard port. A keyboard cable must be connected from the Local Unit to the CPU even if no keyboard is required.
SERVICE and SUPPORT 30 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Service Information Maintenance and Repair This Unit does not contain any internal user - serviceable parts. In the event a Unit needs repair or maintenance, you must first o btain a Return Authorization (RA) number from Rose Electronics or an authorized repair center.
SAFETY CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 31 Safety The CrystalView Plus KVM extender has been tested for conformance to safety regulations and requirements, and has been certified for international use. Like all ele ctronic equipment, the CrystalView Plus should be used with care.
32 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Safety and EMC Regulatory Statements Safety information Documentation reference symbol. If the product is marked wit h this symbol, refer to the product documentat ion to get more information about the product.
APPENDICES CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 33 Appendix A. General specifications Maximum resolution 1600 x 1200 @ 60 Hz (Less than 650 feet / 200M) 1280 x 1024 @ 75 Hz (650 - 1,000 feet / 200 – 300M) Video compatibility VGA to UXGA, RGB Video levels 0.
34 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Dimensions Width In / mm Depth In / m m Height In / mm Local Unit Single video Single video w/serial - audio Dual access Dual access w/serial - a.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 35 Appendix B. Parts and cables Part Number Description CRV - SL1 (Local) Single KVM station / single video CRV - SL2 (Local) Single KVM station / d.
36 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Appendix C. Rack mo unt instructions The optional rack mount kit includes the following items: n Two black anodized mounting brackets or 3 unit mounting shelf. n 6 - 32 x 3/8” flat head mounting screws.
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 37 Appendix D. Rack mount illustration Shelf mount bracket for 3 units Single unit brackets.
38 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL Appendix E. Quick Installation/Setup Guide This appendix provides a quick installation and video compensation guide for experie nced users. Refer to the complete installation guide for a more detailed set of instructions.
NOTES CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 39.
NOTES 40 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL.
.
10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933 - 7673 Internet: WWW.ROSE.COM.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Rose electronic CrystalView Plus è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Rose electronic CrystalView Plus - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Rose electronic CrystalView Plus imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Rose electronic CrystalView Plus ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Rose electronic CrystalView Plus, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Rose electronic CrystalView Plus.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Rose electronic CrystalView Plus. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Rose electronic CrystalView Plus insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
