Manuale d’uso / di manutenzione del prodotto IP Router del fabbricante Ringdale
Vai alla pagina of 12
1 Contents Introduction 2 Installation 3 Using PeripheralVision ® to Configure the IP Router 5 IP Router Page 5 Passwords 6 Routing T able Page 7 Broadcast Forward Page 8 PeripheralVision ® Licensin.
2 Introduction The Ringdale IP Router is a local two port Ethernet IP router which enables IP packets to be routed from one Network/Subnet to another on your Local or Wide Area Network, and even across the Internet if required.
3 Installation Connect the power cord to the Power Input socket as shown in the illustration below and plug into power supply . The LEDs will flash to indicate that the device has powered up. The illustration shows the position of the ports and the diagnostic LEDs.
4 The LEDs are itemized as follows: Link (Y ellow) LED The Link LED indicates that the port is functionally connected to an external port. It lights up when the connected hub is turned on. If the LED does not light up, there may be a problem with the cabling or the hub.
5 Using PeripheralVision ® to Configure the IP Router Full Installation and operational procedures for PeripheralVision ® are dealt with in the separate manual accompanying the Installation CD, refer to this if any problems are encountered in the procedure detailed below .
6 Default Gateway IP Address Enter here the default gateway IP address for Network 1. DNS Name Server Address This information is not necessary . Local IP Address Enter here the router ’ s IP address for Network 2. Local IP Subnet Mask Enter here the subnet mask for Network 2.
7 It is now necessary to tell the IP Router where to route the IP packets to. This is done by creating a Routing T able as above. Configure each route as follows. IP Address Enter here the IP Address of the subnet you want to route to. Subnet Mask Enter here the Subnet Mask of the above IP Address.
8 Click on the Add Route button to add a new route. Click on the Edit Route button to change the configuration of an existing route. Click on the Delete Route button to remove a route. Once the routes have been set up as required, click on Apply . The Ringdale IP Router is now configured and will route your IP packets automatically as specified.
9 T o forward a broadcast through the router to the required IP address click on Add . This will open the window below: Enter the IP address and click on OK . The IP address will be entered into the list. T o make changes to an IP address already on the list, click on the required address to select it and then click on Edit .
10 The device is designed to operate in a typical office environment. Choose a site that is: Well ventilated and away from sources of heat including direct sunlight. Away from sources of vibration or physical shock. Isolated from strong electromagnetic fields produced by electrical devices.
11 Troubleshooting and Technical Reference Symptom Poss. Cause Action LEDs do not flash Power switched off Switch on at power-up Power cord not connected Plug in Router Fuse defect Replace fuse Link L.
12 Technical Support Ringdale Ltd, Ringdale Inc. and Ringdale GmbH all have T echnical Support Departments. Their addresses and contact details are found on the back cover of this manual. Before you call: Please have the following information ready before calling: T ype of adapters installed in the System.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ringdale IP Router è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ringdale IP Router - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ringdale IP Router imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ringdale IP Router ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ringdale IP Router, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ringdale IP Router.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ringdale IP Router. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ringdale IP Router insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
