Manuale d’uso / di manutenzione del prodotto SP 201N del fabbricante Ricoh
Vai alla pagina of 80
Operating Instructions User Guide For safe and correct use, be sure to read "Safety Information" before using the machine..
.
TABLE OF CONTENTS How to Read This Manual .................................................................................................................................4 Introduction .................................................................
If a Paper Mismatch Occurs ............................................................................................................................ 32 Continuing Printing Using Mismatched Paper .....................................................
Consumables .................................................................................................................................................... 69 Print Cartridge .......................................................................
How to Read This Manual Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference.
About IP Address In this manual, "IP address" covers both IPv4 and IPv6 environments. Read the instructions that are relevant to the environment you are using.
Model-Specific Information This section explains how you can identify the region your machine belongs to. There is a label on the rear of the machine, located in the position shown below. The label contains details that identify the region your machine belongs to.
Important Safety Instructions User Information on Electrical & Electronic Equipment Users in the countries where this symbol shown in this section has been specified in national law on collection and treatment of E-waste Our Products contain high quality components and are designed to facilitate recycling.
on 64g/m 2 paper, which contains less raw materials and represents a significant resource reduction. Duplex printing (if applicable) Duplex printing enables both sides of a sheet of paper to be used. This saves paper and reduces the size of printed documents so that fewer sheets are used.
Important Safety Instructions Notes on Lamp(s) Inside This Machine Notes to Users in the State of California Perchlorate Material - special handling may apply.
ENERGY STAR Program ENERGY STAR ® Program Requirements for Imaging Equipment The ENERGY STAR ® Program Requirements for Imaging Equipment encourage energy conservation by promoting energy efficient computers and other office equipment. The program backs the development and dissemination of products that feature energy saving functions.
Energy Saver mode 2 Power Consumption *1 3.1 W or less Default Interval 1 minute Recovery Time *1 17 seconds or less *1 Recovery time and power consumption may differ depending on the conditions and environment of the machine. Recycled Paper We recommend you to use environmentally friendly recycled paper.
12.
1. Guide to the Machine Guide to Components This section introduces the names of the various parts on the front and rear side of the machine and outlines their functions. Exterior CTT108 2 1 9 3 4 5 6 7 8 10 11 13 12 14 1. [Job Reset] key Press this key to cancel an ongoing print job.
5. Stop Fences Raise this fence to prevent paper from falling off. 6. Front Cover Open this cover to replace consumables or clear a paper jam. 7. Bypass Tray This tray can hold one sheet of plain paper. 8. Tray 1 This tray can hold up to 150 sheets of plain paper.
What is Smart Organizing Monitor? Install this utility on your computer from the included CD-ROM before using it. Smart Organizing Monitor provides the following functions: • Displays the status of the machine Displays paper jam messages and other error messages.
Configuring Network Settings This section explains how to configure network settings. • You can configure the IP address easily by installing the driver using Quick Install for networks in the CD-ROM menu. For details about installing the driver, see the Software Installation Guide.
• For details about configuring the IPv4 address, see the Software Installation Guide. Configuring Network Settings 17.
1. Guide to the Machine 18.
2. Loading Paper Supported Paper Paper Size • A4 • 8 1 / 2 " × 11 " (Letter) • 8 1 / 2 " × 14 " (Legal) • B5 • 5 1 / 2 " × 8 1 / 2 " (Half Letter) • 7 1 / .
• Bypass Tray 1 sheets (70 g/m 2 , 19 lb.) 2. Loading Paper 20.
Non-Recommended Paper Types Do not use the following types of paper: • Ink-jet printer paper • GelJet special paper • Bent, folded, or creased paper • Curled or twisted paper • Wrinkled pape.
Print Area The diagram below shows the area of the paper that the machine can print on. From the printer driver CHZ904 2 3 3 1 4 4 1. Print area 2. Feed direction 3. Approx. 4.2 mm (0.2 inches) 4. Approx. 4.2 mm (0.2 inches) • The print area may vary depending on the paper size and printer driver settings.
Loading Paper Load a stack of paper for printing in the input tray. • When loading paper, be sure to configure the paper size and paper type for the bypass tray and Tray 1.
3. Pinch the end paper guide and slide it inward to match the standard size. CTT074 4. Fan the paper before loading it in the tray. 5. Load the new paper stack print side down. Make sure paper is not stacked higher than the upper limit marked inside the tray.
CTT094 Extending Tray 1 to load paper 1. Pull Tray 1 out slowly, and then remove it using both hands. 2. Release the extender locks on both sides of the tray, and then pull out the extender. CTT077 Make sure the extender's inner surface and the scale are aligned.
5. Attach the tray cover. CTT095 • Legal paper or custom-size paper longer than A4 must be loaded without attaching the tray cover. Loading Paper into Bypass Tray 1. Open the bypass tray. CTT063 2. Slide the side guides outward, load paper with the print side up, and then push in until it stops against the machine.
3. Adjust the side guides to the paper width. CTT033 To deliver the sheets face up, open the rear cover. CTT094 Specifying Paper Type and Paper Size Using Smart Organizing Monitor The procedure in this section is an example based on Windows 7. The actual procedure may vary depending on the operating system you are using.
8. Click [Close]. Changing the custom paper size 1. On the [Start] menu, click [All Programs]. 2. Click [Smart Organizing Monitor for SP xxx Series]. 3. Click [Smart Organizing Monitor for SP xxx Series Status]. 4. If the machine you are using is not selected, click [Select Device.
3. Printing Documents Basic Operation Use the printer driver to print a document from your computer. 1. After creating a document, open the [Printing Preferences] dialog box in the document's native application. 2. Change any print settings if necessary.
3. When setting changes are completed, click [OK]. 4. Print the document using the print function in the document's native application. • If a paper jam occurs, printing stops halfway. Open the front cover, remove the print cartridge, and then remove the jammed paper.
Landscape CTT010 6. Press the [Start] key. • If the rear cover is open, the paper is delivered face up from the rear. Rearrange the printed sheets in the correct order. Canceling a Print Job You can cancel print jobs using either the machine's control panel or your computer, depending on the status of the job.
If a Paper Mismatch Occurs If the paper size or type does not match the print job's settings, the machine reports an error. There are two ways to resolve this error: Continue printing using mismatched paper Use the form-feed function to ignore the error and print using mismatched paper.
4. Configuring the Machine Using Utilities Using Web Image Monitor Available operations The following operations can be performed remotely using Web Image Monitor on a computer: • Displaying the mac.
1 3 2 CTT184 1. Menu area If you select a menu item, its content will be shown. 2. Header area The dialog box for switching to the user mode and administrator mode appears, and each mode's menu will be displayed. Click [Refresh] button at the upper right in the work area to update the machine information.
1. Interface Settings The interface setting appears. 2. IPv4 The IPv4 configuration appears. 3. IPv6 The IPv6 configuration appears. 4. Machine Information The machine information appears. Administrator Mode In the administrator mode, you can configure various machine settings.
2. IPv4 You can change the IPv4. 3. IPv6 You can change the IPv6. 4. SNMP You can change the SNMP. 5. Administrator Settings You can change the administrator password. 6. Restore Defaults You can reset the administrator password and other network settings.
Item Description Status Displays the icon indicating the device status. Toner Displays the remaining toner level. Total Counter Displays the total counter.
Item Description Ethernet Speed Ethernet communication speed. For normal use, select Auto Select. This allows the device to select the optimum speed. If communication with the device fails, select 10Mbps Full Duplex, 10Mbps Half Duplex, 100Mbps Full Duplex, or 100Mbps Half Duplex.
Item Description Domain Name Specify whether to use the domain name obtained from the DHCP server, or the domain name set for the device. • "Auto-Obtain (DHCP)" selected When using DHCP, the domain name obtained from the DHCP server is used.
Configuring the IPv6 settings Click [IPv6] to display the page for configuring the IPv6 settings. IPv6 Item Description IPv6 Select whether IPv6 is active or inactive. Ethernet Item Description Host Name Enter the host name you want to set for the network interface board, using up to 63 characters.
Item Description DHCPv6 Select [Enable] to use the DHCPv6 server to automatically configure the network settings. Select [Disable] to manually configure the network settings. DDNS Select whether DDNS (Dynamic DNS) name resolution for the network interface board is active or inactive.
Configuring the SNMP Settings Click [SNMP] to display the page for configuring the SNMP settings. SNMP Item Description SNMP Select whether SNMP is active or inactive for the interface board(s). SNMPv1,v2 Setting Item Description SNMPv1 Trap Communication Select whether to send SNMPv1 trap.
Item Description Access Type In the list, select the access rights to the community. • Not Accessible No access permitted. • read-only You can read the information, but not edit it. • read-write You can read and edit the information. • trap Notifies the manager with information about errors.
Resetting the Machine’s Settings Click [Restore Defaults] to reset the network settings and administrator password. Checking the Machine Information Click [Machine Information] to display machine information. Machine Information Item Description Firmware Version Displays the version of firmware installed on the machine.
Using Smart Organizing Monitor • To use Smart Organizing Monitor, install the printer driver. Checking the Status Information CTT114 1 2 3 4 1. Image area Displays the status of this machine with an icon. 2. Status area • Paper Size Displays the paper size configured on the machine.
4. Message area Displays the status of this machine with a message. For details about error messages, see page 64 "Error and Status Messages Appear on the Smart Organizing Monitor". Configuring the Machine Settings Smart Organizing Monitor is used to modify the machine’s settings.
Printing the Configuration Page • When printing the test page, set the paper size to A4 or Letter. When printing other reports, set the paper size to A4, Letter, or Legal. 1. On the [Start] menu, click [All Programs]. 2. Click [Smart Organizing Monitor for SP xxx Series].
6. On the [User Tool] tab, click [Printer Configuration]. 7. On the [System] tab, click [Printer Firmware Update...]. 8. Click [OK]. 9. Specify the location of the DWN file, and then click [Open].
5. Maintaining the Machine Replacing the Print Cartridge • Store print cartridges in a cool dark place. • Actual printable numbers vary depending on image volume and density, number of pages printed at a time, paper type and size, and environmental conditions such as temperature and humidity.
5. Slide the print cartridge in horizontally, and then slowly push it in all the way. Finally, push the cartridge down until it clicks into place. CTT048 6.
Cautions When Cleaning Clean the machine periodically to maintain high print quality. Dry wipe the exterior with a soft cloth. If dry wiping is not sufficient, wipe with a soft, damp cloth that has been wrung out thoroughly.
Cleaning the Inside of the Machine 1. Open the front cover, and then carefully lower it. 2. Carefully pull out the print cartridge horizontally, holding its center. CTT045 3. Use a cloth to wipe the inside of the machine toward and away from yourself.
6. Troubleshooting Common Problems This section describes how to troubleshoot common problems that may occur while operating the machine. Problem Possible cause Solution The machine does not turn on. The power cord is not connected properly. • Make sure that the power plug is firmly inserted into the wall outlet.
Paper Feed Problems If the machine is operating but paper will not feed or paper jams occur frequently, check the condition of the machine and paper. Problem Solution Paper does not feed smoothly. • Use supported types of paper. See page 19 "Supported Paper".
Problem Solution Paper gets wrinkles. • Paper is damp. Use paper that has been stored properly. • Paper is too thin. See page 19 "Supported Paper". • If there are gaps between the paper and the paper guides, adjust the paper guides to remove the gaps.
Removing Jammed Paper from Tray 1 1. Pull Tray 1 halfway out, and check for jammed paper. If there is jammed paper, remove it carefully. CTT030 2. Carefully slide Tray 1 back in until it stops. 3. Open the front cover, and then carefully lower it. CTT054 4.
5. Lifting the guide plate, remove the jammed paper carefully. CTT046 6. Slide the print cartridge in horizontally, and then slowly push it in all the way. Finally, push the cartridge down until it clicks into place. CTT048 7. Carefully push up the front cover until it closes.
Removing Jammed Paper from the Bypass Tray • Since the temperature around the guide is high, wait for it to cool before checking for jammed paper. 1. If paper is jammed in the bypass tray input area, remove the jammed paper carefully. CTT034 2. Close the bypass tray.
2. Open the fusing cover. CTT079 3. Push the levers on the sides down with your thumbs. CTT080 4. Remove the jammed paper carefully. CTT066 5. Push the levers on the sides up with your thumbs.
7. Close the rear cover. CTT044 6. Troubleshooting 60.
Print Quality Problems Checking the Condition of the Machine If there is a problem with the quality of printing, first check the condition of the machine. Possible Cause Solution There is a problem with the machine's location. Make sure that the machine is on a level surface.
Printer Problems Problem Solution An error occurs. If an error occurs when printing, change the computer or printer driver settings. • Check the printer icon name does not exceed 32 alphanumeric characters. If it does, shorten it. • Check whether other applications are operating.
Print Positions Do Not Match Display Positions If the position of items on the printed page differs from the position displayed on the computer screen, the cause may be one of the following. Possible Cause Solution Page layout settings are not configured properly.
Error and Status Messages Appear on the Smart Organizing Monitor Message Causes Solutions Printer Power Off (Communication Error) • The power cable of the machine is not plugged in. • The power of the machine is not turned ON. • The USB cable or Ethernet cable is not connected.
Message Causes Solutions Print Cartridge Not Detected The print cartridge has not been installed. Reinstall the print cartridge. See page 49 "Replacing the Print Cartridge".
6. Troubleshooting 66.
7. Appendix Notes About the Toner • Proper operation cannot be guaranteed if any third-party toner is used. • Depending on printing conditions, there are cases where the printer cannot print the number of sheets indicated in the specifications.
Moving and Transporting the Machine This section provides cautions that you must follow when moving the machine both short and long distances. Repack the machine in its original packing materials when moving it over a long distance. • Be sure to disconnect all cables from the machine before transporting it.
Consumables Print Cartridge Print cartridge Average printable number of pages per cartridge *1 Black 1,500 pages, 2,600 pages *1 The printable number of pages is based on pages that are compliant with ISO/IEC 19752 with the image density set as the factory default.
Specifications of the Machine This section lists the machine's specifications. General Function Specifications Configuration Desktop Print process Laser electrostatic transfer Maximum paper size for printing 216 mm × 356 mm (8.5 × 14 inches) Warm-up time Less than 25 seconds (23 °C, 71.
Maximum loading height 15.5 mm (0.6 inches) Paper output capacity • Output Tray 50 sheets (70 g/m 2 , 19 lb.) • Rear 1 sheet (70 g/m 2 , 19 lb.) Memory 32 MB Power requirements (mainly Europe and .
Resolution 600 × 600 dpi (maximum: 1200 × 600 dpi) First print speed 10 seconds (From the completion of data processing to the completion of paper delivery) Interface • Ethernet (10BASE-T, 100BASE-TX) • USB 2.
Trademarks Firefox ® is a registered trademark of the Mozilla Foundation. Microsoft ® , Windows ® , Windows Server ® , Windows Vista ® , and Internet Explorer ® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Microsoft ® Windows Server ® 2003 Datacenter Edition • The product names of Windows Server 2003 R2 are as follows: Microsoft ® Windows Server ® 2003 R2 Standard Edition Microsoft ® Windows Serv.
INDEX B Basic operation...................................................... 29 C Changing the custom paper size ......................... 28 Cleaning .......................................................... 51, 52 Common problems .................
MEMO 76 EN GB EN US EN AU M133-8629.
.
EN GB EN US EN A U M133-8629 © 2013.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ricoh SP 201N è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ricoh SP 201N - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ricoh SP 201N imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ricoh SP 201N ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ricoh SP 201N, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ricoh SP 201N.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ricoh SP 201N. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ricoh SP 201N insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
