Manuale d’uso / di manutenzione del prodotto 8030e del fabbricante Ricoh
Vai alla pagina of 114
Operating Instructions Troubleshooting Read this manual carefully before yo u use this machi ne and keep it h andy for future reference. For safe and corre ct use, be sur e t o rea d th e Safety Informatio n in "About This Machi ne" before using the ma chine.
Introduction This manual contains detailed instructions and note s on th e operation and use of this ma chine. For your safety and benefit, read this manual carefully be fo re using the machine. Kee p this manual in a handy place for quick reference. Important Contents of this manual are subject to change witho ut prior notice.
i Manuals for This Machine Refer to the manuals that are relevant to what y ou want to do w ith the machine. Important ❒ Media differ according to manual. ❒ The printed and electronic ve rsions of a manual have the same contents. ❒ Adobe Acrobat Reader/Adobe Reader must be installed in order to view the manuals as PDF files.
ii ❖ Network Guide Explains how to configure and operate the machine in a network environ- ment, and use the software provided. This manual covers all models, and in cludes descriptions of functions and settings that might not be available on this machine.
iii TABLE OF CONTENTS Manuals for This Machine .............................................. ........................................ i How to Read This Manual .............................................. ....................................... 1 Symbols .
iv 5. Troubleshooting When Using the Scanner F unction When Scan Results Are Not As Expected ......................................................... 59 When You Cannot Send Scanned Files .................................. ...........................
v 8. Remarks Where to Put Your Machine ................................................................ ................ 97 Machine Environment ....... .............. .............. .............. ................ .............. .............. . 97 Moving .
vi.
1 How to Read This Manual Symbols This manual uses the foll owing symbols: Indicates important sa fety notes. Ignoring these notes could resu l t i n s e r i o u s i n j u r y o r d e a t h . B e s u r e t o r e a d t h e s e notes. They can be found in the “Safety Information” section of About This Machine.
2.
3 1. When the Machine Does Not Operate As Wanted This chapter describes basic troubleshooting procedures. Indicators This section describes the indicators that light when the machine re quires the user to remove misfed paper, or add paper, toner, or staples.
When the Machine Does Not Operate As Wanted 4 1 When the Function Status Indicator Lights Up in Red When the function status indicator ligh ts up in red, press the corresp onding function key, and then refer to the following table. Reference p.15 “Troubleshooting When Using the Copy Function” p.
When You Have Problems Operating the Machine 5 1 When You Have Problems Operating the Machine This section descri bes co mmon problems and messages. If other messages appear, foll ow the instructions displayed. Important ❒ If you cannot make copies as you want because of paper type, paper size, or paper capacity problems, use recommend ed paper.
When the Machine Does Not Operate As Wanted 6 1 The main power indica- tor continues blinking and does not tu rn off when pressed. This occurs in the follow- ing cases: • The exposure glass cover or ADF is open. • The machine is com- municating with ex- ternal equipme nt.
When You Have Problems Operating the Machine 7 1 Cannot print in duplex mode. Duplex printing cannot be done with thick pa- per, OHP transparencies, or labels selected as the paper type. Select a paper type that allows dupl ex printing. See “Paper Type: Tray 1-4”, General Settings Guide.
When the Machine Does Not Operate As Wanted 8 1 ❖ Document Server Problem Cause Solution “ Scanned pages exceeded max. number. Do you want to store the scanned pages as a file? ” appears. The number of scanned pages exceeds the capac- ity per file of the Docu- ment Server.
When You Have Problems Operating the Machine 9 1 Note ❒ Using curled paper often causes misfee ds, soiled paper edges, or slipped po- sitions while performing staple or st ack printing. When using curled paper, take the stiffness out of the paper with your hands to straighten out the curl, or load the pape r up side down.
When the Machine Does Not Operate As Wanted 10 1 When a Job Is Not Performed I f y o u a r e n o t a b le t o c a r r y o u t y o u r j o b , i t m a y b e t h a t t h e m a c h i ne i s b e i n g u s e d by another funct ion. Wait until the current job is completed before trying ag ain.
When a Job Is Not Performed 11 1 Interrupt Copying Operations for Copying ×××× × ××××× Copying ×××× × → → → ××××× → → Facsimile Transmission Operation/ Manual Recep- tion.
When the Machine Does Not Operate As Wanted 12 1 *1 Simultaneous operations are only possible after the pre ceding job documents are all scanned and [ NextJob ] appears. *2 You can scan a document after the pr eceding job documents are all scanned. *3 When multiple lines are available, select a line which is currently not in use.
When a Job Is Not Performed 13 1 Note ❒ Stapling cannot be used at the same time for multiple functions. ❒ A machine with the 500–sheet finisher installe d cannot accept other jobs while printing with the stapling operation.
When the Machine Does Not Operate As Wanted 14 1.
15 2. Troubleshooting When Using the Copy Function This chapter de scribes likely caus es of and pos sible solutio ns for copier fu nction problems. When a Message Is Displayed This section describes the machine's ma in messages. If other messages appear, follow the instructions they contain.
Troubleshooting When Using the Copy Function 16 2 Scanned pages exceeded max. number. Do you want to store the scanned pages as a file? The number of scanned pages exceeds the capaci- ty per file o f the Do cu- ment Server. If you want to store scanned originals as a file, press [ Store File ] .
When a Message Is Displayed 17 2 Reference p.5 “When You Have Problems Operating the Machine” “Max. Copy Quantity”, General Settings Guide “Sizes difficult to detect”, Copy/Document Server.
Troubleshooting When Using the Copy Function 18 2 When You Cannot Make Clear Copies This section descr ibes likely caus es of an d possible solutions for unclear copies. Problem Cause Solution Copies appear dirty. Image density is too high. Adjust the image density.
When You Cannot Make Clear Copies 19 2 Reference “Copy Paper”, About This Machine “Placing Originals”, Copy/D ocument Server Reference “Adjusting C opy Image D ensity”, Copy/Document Server Reference “Selecting the Original Type Set ting”, Copy/Document Server Refere nce Parts of images are not copied.
Troubleshooting When Using the Copy Function 20 2 When You Cannot Make Copies As Wanted This section descr ibes likely caus es of an d possible solutions for unclear copies. ❖ Basic Problem Cause Solution Misfeeds occur frequently. The number of sheets loaded exceeds the ca- pacity of the machine.
When You Cannot Make Copies As Wanted 21 2 ❖ Edit When sorting, the pages are divided into two blocks. The memory became full in the middle of sorting and the pages were de- livered in two blocks. You can interrupt copying when the memory become s full.
Troubleshooting When Using the Copy Function 22 2 ❖ Stamp ❖ Combine ❖ Duplex When using the Margin Adjustment function, parts of the original im- age are not copied. There is a lack of margin space on the opposite side of the binding posi tion. Set a narrower margin with User Tools.
When You Cannot Make Copies As Wanted 23 2 Reference “Copy Paper”, About This Machine “Paper Type: Tray 1-4”, General Settings Guide “Front Margin: Left / Righ t”, General Settings Guide .
Troubleshooting When Using the Copy Function 24 2 When Memory Is Full This section describes likely causes of and possible solutions for problems relat- ed to full memory. Note ❒ If you set [ Memory Full Auto Scan R estart ] in User Tools to [ Yes ] , even if the mem- ory becomes full, the memory overflow message will not be displayed.
25 3. Troubleshooting When Using the Facsimile Function This chapter describes likely causes of and possible solutions for facsimile func- tion problems. Adjusting the Volume This section descr ibes how to adju st the volume. You can change the volume of the follo wing sounds that the machine makes.
Troubleshooting When Using the Facsimile Function 26 3 D Press [ Adjust Sound Volume ] . E Press [ Lower ] or [ Louder ] to adjust the volume, and then press [ OK ] . You can hear the actual vo lume by pressing [ Check ] . If you press [ Cancel ] , the volume setting is canceled.
When a Message Is Displayed 27 3 When a Message Is Displayed This section describes the machine's ma in messages. If other messages appear, follow their instructions. Message Cause Solution Put original back, check it and press [Start]. Original jammed during Memo- ry Transmission.
Troubleshooting When Using the Facsimile Function 28 3 Cannot scan to send fax message as scanner is in use for other function. The Copy or Document Server function is in use. To cancel the job in process, do the following, and then try faxing again. Press [ Exit ] , and then press the { Copy } or { Document Server } key.
When a Message Is Displayed 29 3 Check whether there are any network prob- lems. [13-10] The alias telephone number you entered is already registered on the gatekeeper by another device. • Check that the alias telephone number i s correctly pro- grammed in IP-Fax Settings un- der Facsimile Fe atures.
Troubleshooting When Using the Facsimile Function 30 3 Check whether there are any network prob- lems. [14-01] Cannot find the DNS server, SMTP Server or folder for for- warding. • Check that the DNS server IPv4 address is correctly pro- grammed using Web Image Monitor.
When a Message Is Displayed 31 3 Check whether there are any network prob- lems. [14-09] E-mail transmission was re- fused by SMTP authentication, POP before SMTP authe ntica- tion or login authentication of the computer in which the fold- er for transfer is specified.
Troubleshooting When Using the Facsimile Function 32 3 Check whether there are any network prob- lems. [15-01] No POP3/IMAP4 server ad- dress is programmed. • Check that the host name or IPv4 address of the POP3/IMAP4 server is co rrect- ly programmed using the Web Image Monitor.
When a Message Is Displayed 33 3 Check whether there are any network prob- lems. [15-11] Cannot find the DNS server or POP3/IMAP4 server. • Check that the DNS server IPv4 address is correctly pro- grammed using Web Image Monitor. See the Web Image Monitor's Help.
Troubleshooting When Using the Facsimile Function 34 3 Note ❒ If the “ Check whether there are any network problems. ” message ap- pears, the machine is not correctly conn ected to the network or the settings of the machine are not correct.
When You Cannot Send or Receive Fax Messages As Wanted 35 3 When You Cannot Send or Receive Fax Messages As Wanted This section describes likely causes of and possible solutions for transmission and reception-related problems. ❖ Transmission/Reception ❖ Transmission Problem Cause Solution Both transmission and reception are impossible.
Troubleshooting When Using the Facsimile Function 36 3 ❖ Reception LAN-Fax Driver does not work. A high security level is set by the extended security function. Contact the administrator. Transmission is impos- sible, but reception is possible. The setting of the terminal adap- tor used for ISDN connection is incorrect.
When You Cannot Send or Receive Fax Messages As Wanted 37 3 ❖ Printing ❖ Others Problem Cause Solution Background of received images appears dirty. Images from the back of the page appear. Image density is too high. Adjust scan density. See “Image Density (Contrast)”, Facsimile Reference.
Troubleshooting When Using the Facsimile Function 38 3 Reference “Copy Paper”, About This Machine “Connecting the Telephone Line”, Gene ral Settings Guide “E-mail Se ttings”, Gene ral Sett.
When an Error Report Is Printed 39 3 When an Error Report Is Printed A n E r r o r R e p o r t i s p r i n t e d i f a d o c u m e n t c a n n o t b e s u c c e s s f u l l y s e n t o r r e c e i v e d . Possible causes include a problem with the machine or noise on the tele phone line.
Troubleshooting When Using the Facsimile Function 40 3 Turning Off the Main Power / In the Event of Power Failure The following notes concern power fa ilure and turning off the machine. R CAUTION: Important ❒ Do not turn off the main power switch while the power indicator is li t or blinking.
When an Error Occurs Using Internet Fax 41 3 When an Error Occurs Using Internet Fax This section describes reports that the mach ine sends if an Internet Fax error occurs. Error Mail Notification The machine sends the Error Mail Notificati on to the sender when it is unable to successfully receive a particular e-mail messa ge.
Troubleshooting When Using the Facsimile Function 42 3.
43 4. Troubleshooting When Using the Printer Function This chapter describes likely causes of an d possible solutions for printer f unction problems. When You Cannot Connect to the USB Interface This section descri bes how to tro ubleshoot a problem relate d to USB connections.
Troubleshooting When Using the Printer Function 44 4 When a Message Is Displayed during Installation T h i s s e c t i o n d e s c r i b e s w h a t t o d o w h e n a message appears during installation of the printer driv er. Message number 58 or 34 indicate s that the printer driver can- not be installed us ing Auto Ru n.
When a Message Is Displayed during Installation 45 4 For Windows XP Home Edition This section descri bes the procedur e under Windows XP Home Edition. A On the [ Start ] menu, click [ Control Panel ] . B Click [ Printers and Other Hardware ] . C Click [ Printers and Faxes ] .
Troubleshooting When Using the Printer Function 46 4 When a Message Is Displayed This section describes the principal mess ages that appear on the pan el display. If a message not described here appears, act according to the message . Reference Before turning the main power off, s ee “Turning Off the Main Power”, About This Machine.
When a Message Is Displayed 47 4 Alert Messages This section describes the machine Alert messages. Message Cause Solution IEEE 802.11b (Wireless LAN) has a problem. • IEEE 802.11b inter- face unit was not in- serted when the machine was turned on, or it was pulled out after the m achine turned on .
Troubleshooting When Using the Printer Function 48 4 Reference “Printer Features”, General Settings Guide The selected file(s) which you do not have ac- cess privileges to could not be deleted. You have tried to delete files without the authori- ty to do so.
When a Message Is Displayed 49 4 Checking the Error Log If files could not be stored due to printing errors, identify the cause of the errors by checking the error lo g on the co ntrol panel. Important ❒ The most recent 30 errors are stor ed in the error log.
Troubleshooting When Using the Printer Function 50 4 When You Cannot Print This section describes what to do if prin ting does n ot start ev en after per forming [ Print ] . Problem Cause Solution Printing does not start. The power is off. Check that the cable is securely plugged into the power outlet and the machine.
When You Cannot Print 51 4 Reference “Turning On t he Power”, About This Machi ne “Connecting the Machine”, General Settings Guide “Interface Sett ings”, Genera l Settings Guide “Printing the Configuration Pa ge”, General Settings Guide Printing does not start.
Troubleshooting When Using the Printer Function 52 4 When the Data In Indicator Does Not Light Up or Flash When the Data I n indicator does not light up or flash after star ting a print job, data is not being sent to the machine.
Other Printing Problems 53 4 Other Printing Problems This section describes likely causes of and possible solutions for problems that can occur when printi ng from a computer. Problem Cause Solution The printed image is smudged. Settings for thick pa- per have not been made when printing on thick paper in the bypass tray.
Troubleshooting When Using the Printer Function 54 4 It takes a long time to complete a print job. The data is so large or complex that it takes time to process. If the Data In indicator is blinking, data is be- ing processed. Wait for a while. It takes a long time to complete a print job.
Other Printing Problems 55 4 It takes a long time to complete a print job. Photographs and oth- er data intensive pag- e s t a k e a l o n g t i m e f o r the machine to pro- cess, so simply wait when printing such data. If the Data In indicator is blinking, data has been received by the printer.
Troubleshooting When Using the Printer Function 56 4 It takes a long time to complete a print job. Photographs and oth- er data intensive pag- e s t a k e a l o n g t i m e f o r the machine to pro- cess, so simply wait when printing such data.
Other Printing Problems 57 4 Reference “Paper Type: Tray 1-4”, General Settings Guide “Timer Settings”, Ge neral Settings Guide “Interface Sett ings”, Genera l Settings Guide “Installing the Printer Driver Using USB”, Printer Reference Duplex printing is malfunctioning.
Troubleshooting When Using the Printer Function 58 4.
59 5. Troubleshooting When Using the Scanner Function This chapter describes likely causes of and possible solutions for scanner func- tion problems. When Scan Results Are Not As Expected This section describes causes and remedies when scan results are not as expected.
Troubleshooting When Using the Scanner Function 60 5 When You Cannot Send Scanned Files This section describes likely causes of an d solutions for problems related to net- work delivery and sending e-mail. When Stored Files Cannot Be Accessed This section describes likely causes of and possible solutions for job access-relat- ed problems.
When You Cannot Send Scanned Files 61 5 When Stored Files Cannot Be Edited This section describes likely causes of an d possible solutions for stored files be- ing unable to be edited.
Troubleshooting When Using the Scanner Function 62 5 When a Message Is Displayed This section describes likely causes of and possible soluti on s for error messages that might ap pear on the machine's co ntrol panel.
When a Message Is Displayed 63 5 Exceeded max. number of files which can be sent at the same time. Reduce the number of the selected files. The number of files ex- ceeded the maximum number possible. Reduce the number of files and send them again. Cannot detect original size.
Troubleshooting When Using the Scanner Function 64 5 Exceeded max. number of alpha- numeric charac- ters for the path. The maximum number of specifiable alphanu- meric characters in a path has been exceeded. The maximum number of characters which can be entered for the path is 128.
When a Message Is Displayed 65 5 Connection with the destination has failed. Check the status and connection. To check the current status, press [Scanned Files Status]. The correct Netwo rk set- tings are not made. • Check the network settings of the cli- ent computer.
Troubleshooting When Using the Scanner Function 66 5 Transmission has failed. Insuffi- cient memory in the destination hard disk. To check the current status, press [Scanned Files Status]. Transmission has fai led. There was not enough free space on the hard disk of the SMTP server, FTP server, or client com- puter at the destination.
When a Message Is Displayed 67 5 Entered protec- tion code for destination is incorrect. Please re-enter. The correct pr otect desti na- tion code was not enter ed. Check that the protection code is correct, and then enter it again. See “Registering a Protection Code”, General Settings Guide.
Troubleshooting When Using the Scanner Function 68 5 Memory is full. Cannot scan. The scanned data will be deleted. Because of insufficient hard disk space, the f irst page could not be scanned. Try one of the following measures: • Wait for a while, and then retry the scan operation.
When a Message Is Displayed 69 5 Reference “Turning Off the Main P ower”, About This Machine “System Settings”, General Settin gs Guide “Send Settings”, General Settings Guide “Registeri.
Troubleshooting When Using the Scanner Function 70 5 Cannot add any more scanning mode. The maximum number of registerable scan modes has been exceeded. The maximum number of modes that can be stored is 99. Delete unneeded modes. Cannot specify any more scanning area.
When a Message Is Displayed 71 5 Fatal error has occurred in the scanner. An unrecoverable error has occurred on the machine. Contact your service representative. Cannot connect to the scanner. Check the network Access Mask set- tings in User Tools. An access mask is set.
Troubleshooting When Using the Scanner Function 72 5 Reference “Turning Off the Main P ower”, About This Machine “Network Settings”, General Settings Guide “Using telnet”, Network Guide Error has oc- curred in the scanner driver. An error has occurred in the driver.
73 6. Adding Paper, Toner and Staples This chapter describes troubleshooting proc edures that are applicable to all the machine's functions. Loading Paper This section descr ibes what to do w h en paper runs out and needs reloading. Note ❒ Fan the paper before loading.
Adding Paper, Toner and Staples 74 6 Setting special paper in paper tray 2 This section descr ibes how to load special paper into paper tray 2. A Pull out the paper tray until it stops. B Load the special paper below the limit mark of the tray. C Push the paper tray in until it stops.
Loading Paper 75 6 Loading Paper into the Larg e Capacity Tray (Optional) This section descri bes how to load paper into the large capaci ty tray (LCT). Important ❒ Load copy paper of the same size and orientation in both left and right side trays. ❒ The tray can hold up to 2,000 sheets.
Adding Paper, Toner and Staples 76 6 Orientation-fixed paper or two-sided paper This section describes load ing paper that has a specif ied orientation and printing side (such as letterhead paper).
Changing the Paper Size 77 6 Changing the Paper Size This secti on describes how t o change the paper si ze. Important ❒ If you want to change the paper size set in the LCT, contact your service representative. Note ❒ Be sure to select the pape r size with User Tools and the paper size selector.
Adding Paper, Toner and Staples 78 6 D Release the side lever. E While pressing the release lever, adjust the side guides. F Square the paper, and then load it in the tray with the copying face up. G While pressing the release lever, adjust the side guides to the new paper size.
Changing the Paper Size 79 6 H Lock the side lever. I While pressing the release lever, adju st the back guide to the new paper size. J Adjust the paper size selector to the new paper size. K Gently push the paper tray in until it stops. L Check the paper size shown on the display panel.
Adding Paper, Toner and Staples 80 6 Changing to a size that is not i ndicated on the pa per size selector If you load a paper size that is not indi cated on the paper size selector, you need to specify the paper size with the control panel. This section describes how to load such paper.
Adding Toner 81 6 Adding Toner This section describes how to add and store toner. R WARNING: R CAUTION: R CAUTION: R CAUTION: R CAUTION: R CAUTION: Important ❒ Fault may occur if you use toner other than th e recommended type. ❒ When adding toner, do not turn off the operat ion switch.
Adding Paper, Toner and Staples 82 6 Removing Toner This section describes how to remove toner. Inserting Toner This section describes how to insert toner.
Adding Toner 83 6 Sending Fax Messages When Toner Has Run Out When the machine has run ou t of toner, the indicator on the display lights. Note that even if th ere is no toner le ft, you can still send fax docum ents.
Adding Paper, Toner and Staples 84 6 Adding Staples This section descr ibes what to do whe n staples need repla cing. Important ❒ Stapling failures or jams may occur if you use a staple cartridge other than that recommended. 500-Sheet Finisher This section describes how to add staples to the 500-Sheet Finishe r.
Adding Staples 85 6 1000-Sheet Finisher This section describes how to add staples to the 1000-Sheet Finisher. ARU004S.
Adding Paper, Toner and Staples 86 6 Replacing the Stamp Cartridge When the stam p becomes faint, replace t he cartridge. Important ❒ This stamp cartridge is used for facsimile and scanner functions. ❒ Do not attempt to put ink into the cart ridge.
Replacing the Stamp Cartridge 87 6 C Pull out the old stamp cartridge. Tap the cartridge lock lever several time s. The cartridge will eject. Then re- move the cartridge, while push ing the lock lever. D Insert the new stamp cartridge. Insert the cartridge until the metal parts are no longer visible.
Adding Paper, Toner and Staples 88 6.
89 7. Clearing Misfeeds This chapter describes what to do when paper or originals misfeed (become jammed inside the machine). Removing Jammed Paper This section descr ibes how to lo cate and remove jamm ed paper. R CAUTION: R CAUTION: Important ❒ When clearing misfeeds, do not turn o ff the operation switch.
Clearing Misfeeds 90 7 Locating Jammed Paper If a misfeed happens, remove the misfed paper or original following the proce- dures shown on the sticker inside the finisher or front cover. Lit indicators show you the locat ion of the misfeed. Note ❒ More than one misfed area may be in dicated.
Removing Jammed Paper 91 7 When A Is Lit This section descr ibes how to re move jammed paper when A is lit. When B Is Lit This section descr ibes how to re move jammed paper when B is lit. When C Is Lit This section descr ibes how to re move jammed paper when C is lit.
Clearing Misfeeds 92 7 When D Is Lit This section descr ibes how to re move jammed paper when D is lit. When P Is Lit This section descr ibes how to re move jammed paper when P is lit.
Removing Jammed Paper 93 7 When R Is Lit This section descr ibes how to re move jammed paper when R is lit. When Y Is Lit This section descr ibes how to re move jammed paper when Y is lit.
Clearing Misfeeds 94 7 When Z Is Lit This section descr ibes how to re move jammed paper when Z is lit. ARU013S.
Removing Jammed Staples 95 7 Removing Jammed Staples This section descr ibes how to remove jammed staples. Important ❒ Curled paper may cause staples to jam.
Clearing Misfeeds 96 7 1000-Sheet Finisher This section describes how to remove jammed staples from the 1000-Sheet Finisher. ARU015S.
97 8. Remarks This chapter describes how to maintain and o perate the machine. Where to Put Your Machine This section describes precautions for installation, relocation, and disposal. Machine Environment Choose your machine' s location carefully.
Remarks 98 8 Environments to avoid • Locations exposed to dire ct sunlight or other sour ces of strong light (more than 1,500 lux). • Locations directly exposed to cool air from an air conditioner or heated air from a heater. (Sudden temperature ch anges can cause condensation to form inside the machine.
Where to Put Your Machine 99 8 Power Connection This section describes the power supply. R WARNING: R WARNING: R CAUTION: R CAUTION: • When the main power switch is in the stand-by position, th e optional anti- condensation heaters are on. In an em ergency, unplug the machine's power cord.
Remarks 100 8 Access to the Machine Place the machine near the power source , provi ding the clearance areas shown. 1. Rear: more than 1 cm (0.4") 2. Right: more than 1 cm (0.4") 3. Front: more than 75 cm (29.6") 4. Left: more than 1 cm (0.
Maintaining Your Machine 101 8 Maintaining Your Machine If the exposure glass, exposure glass cover, o r A D F b e l t i s d i r t y , c o p y c l a r i t y m a y be reduced. Clean the se parts if they are dirty . Important ❒ Do not use chemica l cleaners or orga ni c solvents, such as thinner or benzene.
Remarks 102 8 Cleaning the Exposure Glass Cover This section descr ibes how to clean the exposure glass cover. Cleaning the Auto Document Feeder This section descr ibes how to clean the ADF.
103 INDEX A Add Staple indicator , 3 Add Toner indicator , 3 ADF belt is dirty , 101 Authenticati on failure , 5 C Changing the paper size , 77 Combine , 20 Copies appear dirty , 18 Copies are too lig.
104 EN USA D008-6802 S Scanned image contains white spaces , 59 Scanned image is dirty , 59 Scanned image is dis torted , 59 Scanned image is out of position , 59 Scanned image is upside dow n , 59 Sc.
In accordance with IEC 60417, this machine uses the fol lowing symbols for the main power switch: a means POWER ON. c means STAND BY. Trademarks Microsoft ® , Windows ® and Windows NT ® are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Operating Instructions Troubleshooting Type for 8025e/DSm725e/LD3 25/Aficio MP 2510 Type for 8030e/DSm730e/LD3 30/Aficio MP 3010 EN USA D008-6802.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ricoh 8030e è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ricoh 8030e - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ricoh 8030e imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ricoh 8030e ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ricoh 8030e, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ricoh 8030e.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ricoh 8030e. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ricoh 8030e insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
