Manuale d’uso / di manutenzione del prodotto AMP-591A del fabbricante Audiovox
Vai alla pagina of 15
Owner's Owner's Owner's Owner's Owner's Manual Manual Manual Manual Manual Model AMP-591A 300 W att S tereo Amplifier.
INDEX Specifications .............................................................................1 Precautions ................................................................................2 Installation Instructions ...............................
HIGH PERFORMANCE STEREO AMPLIFIER This power amplifier has been designed to provide high quality performance with a minimum of maintenance. However, it's performance will only be as good as the care and quality of components with which it is installed.
PRECAUTIONS 1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive ( + ) terminal of the battery.
INSTALLATION INSTRUCTIONS INSTALLATION DIAGRAM 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode.
WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for both types. Please refer to the appropriate diagrams for the system configuration you are using.
4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge.
R L LOW INPUT HPF LPF STEREO AND MIXED-MONO INPUT WIRING DIAGRAM -6- 5-PIN CONNECTOR IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUTS, NOT BOTH. HIGH-LEVEL (SPEAKER) OUTPUTS CAR STEREO USE THIS INP.
- LEFT SPEAKER - + RIGHT SPEAKER + STEREO MOD E:2-8 OHMS MIXED-MONO MOD E:4-8 OHMS STEREO MOD E:2-8O H M S MIXED-MONO MOD E:4-8 OHMS STEREO AND MIXED-MONO OUTPUT WIRING DIAGRAM -7- AUT.
R L LOW INPUT HPF LPF PROT PWR BASS BOOST X-OVER GAIN -8- MONO (BRIDGED) INPUT WIRING DIAGRAM CAR STEREO LOW-LEVEL RCA OUTPUTS "Y" RCA TYPE SHIELDED CABLE (NOT SUPPLIED) TO 2nd AMPLIFIER IMPORTANT USE EITHER HIGH OR LOW-LEVEL INPUTS, NOT BOTH.
-9- MONO (BRIDGED) OUTPUT WIRING DIAGRAM USE THIS OUTPUTWIRING WITH INPUT WIRING ON PAGE8 AUTO-ANTENNA LEAD USE #16 GAUGE WIRE (SEE TEXT) CAR STEREO CONNECT THIS WIRE LAST EXISTING SCREW OR BOLT CLEAN.
R L LOW INPUT HPF LPF PROT PWR BASS BOOST X-OVER GAIN HI-INPUT BRIDGED LEFT LEFT RIGHT RIGHT 20A GND REM BATT POWER FUSE SPEAKER OUT -10- OPERATION After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used.
-11- overload condition, the source of the overload must be found an d corrected to resume operation of the amplifier. Most overload conditions are caused by mis-wiring or operation into incorrect speaker loads. Re-check all wiring and connections if this situation occurs and correct as necessary.
Crossover Selector 4 is in the "HPF" setting. Adjust it to the appropriate position for t he characteristics and crossover frequency requirements of the speaker system with which t he amplifier is being used. 7 Bass Boost Switch This switch is used to accentuate the bass frequencies by adding 10 dB of boost to the signal (at 50 Hz.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in mater.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Audiovox AMP-591A è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Audiovox AMP-591A - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Audiovox AMP-591A imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Audiovox AMP-591A ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Audiovox AMP-591A, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Audiovox AMP-591A.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Audiovox AMP-591A. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Audiovox AMP-591A insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
