Manuale d’uso / di manutenzione del prodotto Signature, Inscripta rinter Autoloader del fabbricante Primera
Vai alla pagina of 18
Operator’s Manual For Use With the Signature ® III CD Color Printer or Inscripta™ Thermal CD Printer Two Carlson Parkway North • Plymouth, MN 55447-4446 U.S.A. Phone: 1-800-797- 2772 • 763-475-6676 • FAX: 763-475-6677 Internet: www.primeratechnology.
2.
3 © 2000 All rights reserved. Notices: The information in this document is subject to change without notice. NO WARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
4 For Users in Canada: This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out on the Radio Interference Regulations of the Canadian Department of Communications.
5 Table of Contents SECTION 1: GETTING STARTED A. Introduction ........................................................................................................... 6 B. Choosing a Good Location ..................................................
6 SECTION 1 : GETTING STARTED A. Introduction Thank you . . . . . . for purchasing a Conductor Printer Autoloader. This device automates the transport of up to 50 optical discs (CD-R, DVD-R, etc.) per batch into and out of a Primera Technology Signature III CD Color Printer or Inscripta Thermal CD Printer.
7 Front Panel and Top Ink Jet CD Printer Robotic Arm Input Bin LED Status Light Pick Button Sequence Button Pause Button Control Panel Output Bin CD Printer Tray Figure 1: Conductor and Signature III .
8 Rear Panel This illustration shows the input ports found on the rear panel of Conductor: Power Input Por t Printer Control Por t Control Port SCSI Por t Figure 3: Rear Panel of Conductor Please note that the SCSI port is not installed on your Conductor.
9 SECTION 2: HARDWARE AND CABLE SET-UP A. Connecting the Parts and Interface Cables Follow these steps to integrate your autoloader and printer: 1. In the Conductor shipping box you will find the Input and Output Bins. Place the Bins in their correct places as shown in Figure 1.
10 1 2 Figure 6: Attaching the Printer Stand Make sure that the Printer Control Cable is routed neatly out the back of the Printer Stand so that it can be connected to your printer. If you are using the Inscripta Thermal CD Printer, you will also need to install a Tray Support Bracket to the top cabinet of the Conductor.
11 6. Connect the other end of the Printer Control Cable to the printer’s rear-panel 6-pin mini-DIN port. Figure 9: Connecting the Printer Control Cable 7. Connect both ends of the Parallel Cable. One end is connected to the Parallel Input Port on the rear panel of the printer.
12 B. Hardware Test 1. Load the Input Bin with at least 4-5 CDs and place the output bin in the proper location. Figure 12 : Loading CDs 2. Press the Sequence Button on Conductor’s front panel. The Robotic Arm will swing over to and above the Input Bin.
13 NOTE TO USERS OF SIGNATURE AND SIGNATURE II CD COLOR PRINTERS: Due to a slight difference in CD Tray length between these earlier models, the instructions for adjusting the printer on the Printer Stand may not lead you to a perfect alignment.
14 SECTION 3: INTERPRETING THE LED STATUS LIGHTS The LED Status Lights, located on Conductor’s front panel, can tell you a lot about what is happening at any given moment with the operation of the autoloader. To accurately interpret what is meant when the lights are on, off or flashing, refer to the following chart: A.
15 SECTION 4: MAINTENANCE AND TROUBLESHOOTING Conductor is designed to operate for extended periods of time with very little attention. In fact, no regular maintenance is recommended other than cleaning the outside case. IMPORTANT: Do NOT attempt to oil or grease the Duplicator’s Robotic Arm shaft or other components.
16 SECTION 5: TECHNICAL SPECIFICATIONS Model Conductor Printer Au toloader Robotics Controlled by Primera Technology Signature, Signature II or Signature III CD Color Printers or Inscripta Thermal CD .
17 INDEX Bins Input ..................................................................................................................... 7, 9 , 12, 13 Output ............................................................................................
18 Tech Support ............................................................................................................................. 15 Tray Support Bracket .....................................................................................
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Primera Signature, Inscripta rinter Autoloader è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Primera Signature, Inscripta rinter Autoloader - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Primera Signature, Inscripta rinter Autoloader imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Primera Signature, Inscripta rinter Autoloader ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Primera Signature, Inscripta rinter Autoloader, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Primera Signature, Inscripta rinter Autoloader.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Primera Signature, Inscripta rinter Autoloader. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Primera Signature, Inscripta rinter Autoloader insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
