Manuale d’uso / di manutenzione del prodotto 177271 del fabbricante Poulan Pro
Vai alla pagina of 52
1 OWNER'S MANUAL MODEL: PRGT2046A LA WN TRACTOR Always Wear Eye Protection During Operation W ARNING: Read this Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. IMPORT ANT MANUAL Do Not Throw A way 177271 Rev.
2 I. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting. • Only allow responsible adults, who are familiar with the instructions, to operate the machine. • Clear the area of objects such as rocks, toys, wire, etc.
3 Safe Operation Practices for Ride-On Mowers SAFETY RULES • Check brake operation frequently. Adjust and service as required. • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off.
4 PRODUCT SPECIFICA TIONS GASOLINE CAPACITY 3.5 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 10W-30 (above 32 ° F) SAE 5W-30 (below 32 ° F) OIL CAPACITY: W/ FILTER: 4.0 PINTS W/O FILTER: 3.75 PINTS SPARK PLUG: CHAMPION RC12YC (GAP: .
5 CONTENTS OF HARDW ARE P ACK Steering Wheel Insert Steering Wheel Mower Gauge Wheels Steering Wheel Seat Steering Sleeve Steering Sleeve Extension (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge (2) Front Link Assemblies (3) Retainer Springs (double loop) (4) Retainer Springs (single loop) (4) Washers 3/8 x 3/4 x 14 Ga.
6 ASSEMBL Y Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
7 ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4) The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower performance. • Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top.
8 ASSEMBL Y FIG. 4 SHOULDER BOLT GAUGE WHEEL 3/8-16 CENTER LOCKNUT 3/8 WASHER ADJUSTING BAR PIN RETAINER SPRING I NSTALL MULCHER PLATE (See Fig. 6) NOTE: If you installed the mulching blades you will need to install the mulcher plate. • Raise and hold deflector shield in upright position.
9 ASSEMBL Y FIG. 7 • Turn height adjustment knob counterclockwise until it stops. • Lower mower linkage with attachment lift control. • Place the suspension arms on inward pointing deck pins. If necessary, rock and raise front of mower to align deck pins with the holes in suspension arms.
10 ASSEMBL Y CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRAC- TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed.
11 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING REVERSE FORWARD FAST SLOW ENGINE ON EN.
12 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR. Compare the illustrations with your tractor to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
13 HOW TO USE YOUR TRACT OR TO SET PARKING BRAKE (See Fig. 9) Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.
14 ADD GASOLINE • Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.
15 OPERA TION TO START ENGINE (See Fig. 9) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Sit on seat in operating position, depress clutch/brake pedal and set parking brake.
16 CUST OMER RESPONSIBILITIES BEFORE EACH USE T R A C T 0 R Adjust Motion Drive Belt(s) Tension Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oi.
17 BLADE REMOVAL (See Fig. 14) • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and flat washer securing blade. • Install new or resharpened blade with trailing edge up towards deck as shown. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.
18 V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.
19 ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage.
20 FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23) - IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.
21 FRONT LINKS NUT “ H ” NUT “ G ” FIG. 23 TO REPLACE MOWER DRIVE BELT MOWER DRIVE BELT REMOVAL (See Fig. 24) - • Park tractor on a level surface. Engage parking brake. • Remove screws from L.H. mandrel cover and remove cover. • Roll belt over the top of L.
22 TO ADJUST ATTACHMENT CLUTCH (See Fig. 26) The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required.
23 FIG. 31 RETAINING RING WASHERS AXLE COVER SER VICE AND ADJUSTMENTS TO REMOVE WHEEL FOR REPAIRS FRONT WHEEL (See Fig. 31) • Block up axle securely. • Remove axle cover, retaining ring and washers to allow wheel removal. • Repair tire and reassemble.
24 TO REPLACE FUSE Replace with 30 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TO ADJUST ATTACHMENT LIFT SPRING (See Fig. 34) • While holding spring bushing with wrench, loosen jam nut. • Turn adjustment bolt clockwise to extend spring and reduce lift effort for heavier attachments.
25 SER VICE AND ADJUSTMENTS ADJUSTMENT BOLT SPRING BUSHING JAM NUT ATTACHMENT LIFT SPRING FIG. 34 CLAMP SCREW FIG. 37 FIG. 36 SWIVEL CLAMP SCREW STOP ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 36) The throttle control has been preset at the factory and adjustment should not be necessary.
26 ST ORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “ CHOKED ” properly. 2. See “ TO START ENGINE ” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
28 TROUBLESHOOTING POINTS Engine continues to run 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutch department.
29 TRACTOR - - MODEL NUMBER PRGT2046A SCHEMA TIC BATTERY FUSE RED RED BLACK BLACK BLACK BLACK BLACK BLACK BLACK BLACK BLACK NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS BLACK BLACK BROWN RED ORANGE.
30 30 33 24 42 43 40 26 28 25 50 29 27 27 41 16 12 12 11 10 8 2 1 27 D .C . A M P E R E S 45 81 52 22 21 79 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A ELECTRICAL.
31 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A ELECTRICAL 1 144926 Battery 2 74760412 Bo lt H e x H e a d 1 /4 - 2 0 x 3 / 4 8 7603J Tray, Battery 1 0 145211 Bolt Btr Frt 1/4-20 X 7.
32 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A CHASSIS AND ENCLOSURES 50 43 42 17 17 17 21 21 44 20 21 84 47 24 86 4 2 19 20 16 17 56 21 47 17 28 91 1 106 8 68 17 90 17 6 7 7 7 30 67 85 88 137 1.
33 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A CHASSIS AND ENCLOSURES 1 175465 R a il, Frame RH 2 140506 Drawbar, Gt 4 73680700 Nut, Crownlock 7/16-14Unc 5 163976X428 Dash 6 157882 Dash Asm., Lower 7 17720408 Screw, Thd Cut 1/4-20 x 1/2 8 145166 Support, Battery 1 4 175259X428 Hood Asm.
34 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A GROUND DRIVE 62 150 3 69 7 8 9 10 11 27 14 13 16 18 19 26 21 22 23 25 24 37 38 40 41 42 23 59 60 61 12 62 63 56 39 67 5 117 50 6 15 48 53 55 52 54 .
35 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A GROUND DRIVE KEY P A RT N O . N O . DESCRIPTION KEY P A RT N O . N O . DESCRIPTION NOTE: All component dimensions given in U.
36 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A STEERING ASSEMBL Y 8 6 29 28 23 31 41 22 21 20 44 1 45 14 25 34 33 32 6 27 42 27 6 19 15 14 35 18 16 9 8 7 2 6 6 4 14 15 14 14 15 9 3 8 7 3 6 6 5 1.
37 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A STEERING ASSEMBL Y 1 159944X428 W heel, Steering 2 137094 A x l e Asm., Front 3 6855M Fitting, Grease 4 161849 S p i n d l e Asm, LH 5 161848 Spindle Asm., RH 6 6266H Bearing, Race Thrust Harden 7 121748X Washer 25/32 x 1-5/8 x 16 Ga.
38 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A ENGINE 1 84 24 12 11 41 42 43 10 9 8 40 29 SPARK ARRESTER KIT 84 45 47 39 18 15 17 37 28 37 27 26 16 22 25 21 20 74 62 71 70 79 69 83 35 2 81 82 31.
39 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A ENGINE KEY P A RT N O . N O . DESCRIPTION 1 - - - - - - - Engine Briggs Model # 407777 2 149723 M u ffler 8 121361X P u l l e y V-Idler 9 150828 Keeper Asm Belt Engine Vgt 96 1 0 175287 Bushing 1 1 170056 C lutch Electric 1 2 143996 P u l l e y Engine Grnd Drive 1 5 151346 Tank Fuel Rear 3.
40 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A SEA T ASSEMBL Y 1 171684 Seat 2 140551 Bracket, Pivot Seat 3 140675 S trap, Fender Asm. 4 127018X Bolt, Shoulder 5/16-18 x .62 5 145006 C lip, Push-In Hinged 6 73800600 Nu t, Lock Hex w/Ins. 3/8-16 Unc 7 124181X Spring, Seat Cprsn.
41 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A DECALS 23 3 9 14 5 4 12 23 5 10 19 16 1 11 KEY P AR T N O . N O . DESCRIPTION KEY P AR T N O . N O .
42 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A LIFT ASSEMBL Y 35 73 34 32 31 30 4 5 5 4 2 11 11 7 8 9 10 3 6 1 14 41 14 41 12 13 13 21 19 20 15 73 16 26 78 24 22 23 12 12 12 23 23 23 18 38 39 40.
43 KEY P A RT N O . N O . DESCRIPTION 1 121006X Rod Asm., Lever 2 159187 S haft Asm., Lift Vgt 3 159189 Lever Asm., Lift Rh 4 12000022 E-Ring Truarc #5133-87 5 19292016 Washer 29/32 x 1-1/4 x 16 Ga.
44 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A MOWER DECK 57 56 118 116 119 5 117 46 45 33 49 41 42 49 36 37 43 40 46 45 50 44 33 30 30 32 21 20 18 18 21 34 31 127 41 42 44 35 50 40 126 72 52 38.
45 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A MOWER DECK KEY P A RT N O . N O . DESCRIPTION KEY P A RT N O . N O . DESCRIPTION 1 156833 Deck Weldment 2 138457 Bracket Asm., Sway Bar 5 4939M R e t a i n e r S pr i n g 6 130832 Arm, Suspension, Rear (Sway Bar) 8 850857 B o lt, Patched 3/8-24 x 1-1/4 Gr.
46 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A TRANSAXLE.
47 REP AIR P ARTS TRACTOR - - MODEL NUMBER PRGT2046A TRANSAXLE KEY P A RT N O . N O . DESCRIPTION 1 4197R A xle Shaft 2 12000034 Retaining Ring 3 4199R Final Drive Gear 4 4216R Differential Gear 5 421.
48.
49.
50 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship.
51 15 MAX. SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. CUT OUT ON DOTTED LINES THIS IS A 15 SLOPE SIGHTING GUIDE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION Operate your Tractor up and down the face of slopes (not greater than 15 ), never across the face.
Your POULAN PRO product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SERVICE OR REPLACEMENT PARTS: 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Poulan Pro 177271 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Poulan Pro 177271 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Poulan Pro 177271 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Poulan Pro 177271 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Poulan Pro 177271, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Poulan Pro 177271.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Poulan Pro 177271. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Poulan Pro 177271 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
