Manuale d’uso / di manutenzione del prodotto ons iGPS-BT II del fabbricante Pharos Science & Applicati
Vai alla pagina of 16
iGPS-BT II User Manual.
FCC Notices This device complies with Part 15(b and c) of the FCC Rules. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, includin g interference that may cause undesired operation.
I. iGPS-500 Receiver and Bluetooth Dock iGPS-BT II Dock iGPS-500 Receiver DC Jack for charging On/Off Swit ch Battery charging indicator (Orange/Green LED) Bluetooth Status Indicator (Internal Blue LED) DC Jack - Plug either the Car charger or 5V AC adapter for your PDA into the DC Jack to charge the battery.
II. iGPS-BT II Setup (see walkthrough guides at the end of this section) 1. The iGPS-BT II will need to be charged for two to three hours before initial use. 2. Turn on the iGPS-BT II. The status indicator will blink as it searches for a Bluetooth connection.
Walkthrough Guides 1. iGPS-BT II Setup for Pocket PCs wit h built-in Bluetooth Technology running the Windows Mobile Pocket PC OS (the following screen shots show the device as “ Pharos iGPS-BT ”, it may be shown as “ Pharos BT GPS II ” on your Pocket PC.
5. Provided that your iGPS-BT II is turned on and fully charged, it will be discovered. Tap on the “ Pharos iGPS-BT ” icon to select it 6. Enter the Passkey: 12345678 , and select “ OK” in the upper right-hand corner 7. Select “ GPS RFcom ” so that it becomes highlighted, and tap on “ Next ” 8.
9. Tap and hold on the “ Pharos iGPS- BT: GPS RFcom ” icon, select “ Connect ” from the Menu that appears 10. Once the GPS has a connection, the icon will change to Green. You will also notice that the Blue light on the GPS itself is now a solid, steady Blue.
13. Now that the COM Port is setup, you can Enable the GPS by tapping on the RED Smiley face 14. Select “ YES ” to Enable the GPS Bluetooth setup for Windows Mobile 5.
2. iGPS-BT II Setup for Pocket PCs with built-in Bluetooth Technology running the Windows Mobile 5.0 OS (the following screen shots show the device as “ Pharos iGPS-BT ”, it might be shown as “ Pharos BT GPS II ” on your Pocket PC.) 2. Click the small Bluetooth icon the bottom right-hand side of the screen.
6. Enter the passkey: 12345678 7. Put a check mark in the box next to “serial port” and tap Finish 8. Next select the “COM Ports” tab at the bottom of the screen. Then select “New Outgoing Port” 9. Select the “Pharos iGPS-BT” and tap, Next.
10. Select Com 7, and make sure that there is a check in the “Secure Conne ction” b ox and tap Finish. 11. Close down the Bluetooth Settings screen and start the Pharos Ostia navigation program.
….. ….. 14. The Smiley Face should go from Red to Yellow when searching for satellites and finally to Green when a GPS lock for navigation has been established . For Bluetooth setup on other devices, please visit: www.pharosgps.com for walkthrough guides under the Support section.
Battery Precautions (w: WARNING!) 1. w Reverse charging is not acceptable. 2. Charge before use. The cells /batteries are delivered in an uncharged state. 3. w Do not charge/discharge with mo re than our specified current (400mA). 4. w Do not short circuit the cell/ battery, permanent damage to the cell/battery may result.
IV. iGPS-BT II GPS Receiver Specifications Performance Chipset SiRF StarIII GSC3f Antenna Integrated patch antenna Frequency L1, 1575.42 MHz Sensitivity -159 dBm Channels 12 Channel a ll-in-view tracking Acquisition time Cold Start: 35 sec (open sky) Hot Start: 1 sec (open sky) Reacquisition 0.
V. Precautions • Position fixing may not be available w hen this receiver is used near high- voltage wire, electronics equipment that generates electrical noise, or mobile phones in operation at 1.5 GHz. The noise from PDA or PC may deteriorate the GPS receiver performance.
VIII. Troubleshooting For any troubleshooting assistance, please check the Frequently Asked Questions section at www.pharosgps.com. IX. Warranty The iGPS-BT II Receiver is warranted by Pharos to the o.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pharos Science & Applications iGPS-BT II è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pharos Science & Applications iGPS-BT II - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pharos Science & Applications iGPS-BT II imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pharos Science & Applications iGPS-BT II ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pharos Science & Applications iGPS-BT II, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pharos Science & Applications iGPS-BT II.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pharos Science & Applications iGPS-BT II. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pharos Science & Applications iGPS-BT II insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
