Manuale d’uso / di manutenzione del prodotto Hobbylock 2.5 del fabbricante Pfaff
Vai alla pagina of 28
Owner’s Manual.
This household sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594 IMPORT ANT SAFETY INS TRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this household sewing machine.
3 T able of contents Parts of the machine ................................................................. 4 Accessories .................................................................................... 5 Connecting the foot control and the power supply .
4 9 10 11 12 13 1 2 3 4 5 6 14 15 19 16 17 18 7 8 24 21 20 26 25 23 22 P arts of the machine 1. Presser foot pressure adjustment knob 2. Left needle thread tension dial (blue) 3. Right needle thread tension dial (green) 4. Upper looper thread tension dial (red) 5.
5 1 2 3 4 5 6 8 9 10 7 Accessories 1. Needle pack including three needles, size #14/90 and two needles, size #12/80. Two needles, size #14/90, are in the machine on delivery. 2. Screwdriver 3. Tweezers 4. Thread unreeling discs (4) 5. Lint brush 6. Knife blade (for the stationary lower cutter) 7.
6 A A Setting up the telescopic thread stand Pull out the spool stand in the direction of the arrow (A) Extend the telescopic thread stand to its full height, then turn until it clicks into place. Place the thread spools or cones over the cone holders on the spool pin.
7 A A Presser foot lift Raise the presser foot with the presser foot lift lever (A) at the back of the machine. Changing the needles Turn off the main power switch and unplug the machine. 1. Turn the hand wheel toward you until the needles are at the highest position.
8 A B C D A Disengage the movable upper cutter Place the movable upper cutter in nonworking position 1. Turn the hand wheel toward you until the upper cutter is raised to the highest position. 2. Open the front cover. 3. Push the movable cutter holder to the right as far as it will go.
9 2 3 4 1 Threading the machine A color coded diagram is located inside the front cover for quick reference. When threading the machine, thread only in the following order: 1. Upper looper threading - (Red) 2. Lower looper threading - (Yellow) 3. Right needle threading - (Green) 4.
10 1 3 2 4 5 6 7 8 8 Threading the upper looper (r ed) 1. Pass the thread from back to front through the thread guides on the thread stand (1). 2. Pull the thread from left to right under the thread guide at the back on the top cover (2). 3. Lift up the handle and bring the thread under it.
11 1 3 2 4 5 6 7 8 10 9 10 9A 9B Threading the lower looper (yellow) 1. Pass the thread from back to front through the thread guide on the thread stand (1). 2. Pull the thread from left to right under the thread guide on the back of the top cover (2).
12 1 1 3 3 4 5 7 8 4 6 7 2 2 6 5 Threading the right needle (gr een) 1. Pass the thread from back to front through the thread guides on the thread stand (1). 2. Pull the thread from left to right under the thread guide on the back of the top cover (2).
13 Changing threads The following is an easy way to change threads: 1. Cut the thread in use near the spool, behind the guides on the telescopic thread stand. 2. Remove the thread spool and place the new thread on the spool pin. 3. Tie the end of the new thread to the end of the old thread.
14 Thread tension settings Set the thread tension to suit the type of fabric and thread used. As the number on the thread tension discs increases, the thread tension becomes tighter. Lower looper thread and upper looper thread should be well balanced with the same tension (both looper threads should cross at the edge of the fabrics).
15 Differential feed adjustment The differential feed system consists of two sets of feed teeth arranged one behind the other. Both feed teeth work independently of each other to give perfect results when sewing on speciality fabrics.
16 Presser foot pr essure adjustment The presser foot pressure is pre-set for sewing based on normal conditions. Adjustment might in some conditions be necessary. Increase or decrease the pressure until you are satis À ed with the result. Always test sew on a sample of your fabric before sewing on your garment.
17 Stitch À nger lever setting The stitch À nger lever should be set to “S” for all standard overlock sewing. To sew rolled edge you need to retract the stitch À nger by setting the stitch À nger lever to “R”. When moving the stitch À nger, be sure to push the lever as far as it will go in each direction.
18 Flatlock sewing A Flatlock Stitch is made by adjusting the tension of the 2- or 3-thread overlock stitch, sewing the seam and pulling the fabric apart to Á atten the seam.
19 Corded overlock Corded overlock can be used to strengthen stitches when joining elastic fabrics such as knits. Cording prevents knit fabrics from stretching and also stabilize the seams. 1. Insert the cord through the hole in the front of the foot.
20 Machine maintenance An overlock requires more frequent maintenance than a conventional machine for two reasons: - A lot of lint is produced when the cutters are cutting the the fabric. - An overlock runs at a very high speed and needs to be oiled frequently to lubricate the internal working parts.
21 1 2 3 Replacing the stationary cutter Turn off the main power switch and unplug the machine. The stationary cutter should be changed when it becomes dull. The stationary cutter can be replaced according to the following directions. If you are having any dif À culties, consult your dealer to make the necessary adjustments.
22 T rouble shooting Problem Solution Page Fabric does not feed well - Lengthen stitch length. - Increase presser foot pressure for heavy weight fabric. - Decrease presser foot pressure for light weight fabric. - Check the differential feed. 16 16 16 15 Needle breaks - Insert needle correctly.
23 Combination Needle position Stitch length Stitch width Differ- ential feed Stitch À nger 2-thread con- verter Thread tension Stitch F abric BG R Y 2-thread overlock, wide Left 3 R(3.5) 1 S Yes 0.0 - - 5.0 0.5 - - 5.0 1.0 - - 5.0 0.0 - - 5.0 1.0 - - 5.
24 Combination Needle position Stitch length Stitch width Differ- ential feed Stitch À nger 2-thread con- verter Thread tension Stitch F abric BG R Y 2-thread overlock, wr ap, narrow Right 3 R(3.5) 1 S Yes - 3.5 - 2.0 - 4.0 - 2.0 - 5.0 - 2.0 - 3.0 - 2.
25 Combination Needle position Stitch length Stitch width Differ- ential feed Stitch À nger 2-thread con- verter Thread tension Stitch F abric BG R Y 3-thread overlock stitch, wide Left 3 R(3.5) 1 SN o 2.5 - 3.0 3.0 3.0 - 3.0 3.0 3.5 - 3.0 3.0 2.5 - 3.
26 Combination Needle position Stitch length Stitch width Differ- ential feed Stitch À nger 2-thread con- verter Thread tension Stitch F abric BG R Y 3-thread rolled edge Right 1 3 1 R No - 2.0 5.0 7.0 - 2.0 5.0 8.0 Not recommended Right 1 3 1 R No - 3.
27 F abric / Needle / Thr ead table F abric Light fabric (voile, crepe, georgette, etc.) Medium fabric (cotton, chino, wool, satin etc.) Heavy fabric (denim, jersey, tweed etc.
413 17 36 - 26E • English • Inhouse • © 2010 KSIN Luxembourg II, S.ar.l. • All rights reserved • Printed in Sweden on environment friendly paper www .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pfaff Hobbylock 2.5 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pfaff Hobbylock 2.5 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pfaff Hobbylock 2.5 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pfaff Hobbylock 2.5 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pfaff Hobbylock 2.5, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pfaff Hobbylock 2.5.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pfaff Hobbylock 2.5. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pfaff Hobbylock 2.5 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
