Manuale d’uso / di manutenzione del prodotto hobby 1010 del fabbricante Pfaff
Vai alla pagina of 15
INSTRUCTION MANUAL FOR SEWING MACHINE 0] Hobby Model 351427004 0012.14 1010 — 37.
IMF’UHIANT 5AFTY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using (this sewing machine) DANGER To reduce the risk of electric shock: An appliance should never be left unattended when plugged in.
NAME OF PARTS (FRONT VIEW) (REAR VIEW) Thread tension dial Bobbin winder Stop Motion knob Hand wheel Bobbin winder spindle Face cover Presser toot Shuttle Extension table Thumb screw Needle plate Zigz.
ACCESSORIES Bobbin Button foot Button hole cutter Felt Zigzag foot (On machine) Machine Oil Screw driver Button hole foot Zipper foot I Needle #11 #14 BEFORE SEWING 1 Fit plug into the machine. 2. Plug the machine to the po y supply. 3. Sewing speed can be varied the foot control.
REMOVING EXTENSION TABLE 1 Hold the left end of table and pull out in diecfion or arrow. WINDING ThE BOBBIN 1 Release stop motion kric 2.Thread as shown. 3.When bobbIn is filk tighten stop motion kno 1. This sewing machine can be used as a fiat bed machine but easily converts to free arm machine by removing the extension table.
2.Open hinged latch of bobbIn case and pull bobbin case out of machine. INSERTING BOBBIN INTO BOBBIN CASE 1.Raise needle to its highest position, pulling thread to the front, open the latch of bobbin case and hold it. I .PulI off 5cm of thread from bobbin and insert it into bobbin case as shown.
THREADING UPPER THREAD 1. Hold upper thread with left hand, turn the hand wheel slcwly towards you until the needle qoes down and comes up. Then stop the hand wheel when the takeup lever is at its highest position. Lightly draw up the upper tbread and the lower thread will be brought up in a loop.
ADJUSTiNG THREAD TENSION CONTROL DIAL Weak Strong Upper thread tension may be adjusted by turning the thread tension dial. Fabric Coaect Incorrect Inside of fabric Upper thread Upper thread Bobbin tbread LOWER THREAD TENSION Lower thread tension can be adjusted by turning screw on bobbin case slight ly to the right (clock-wise) to increase tension.
REGULATING THE PRESSER FOOT PRESSURE 1. Push down inner pin (A) to increase pressure. (Light to medium fabrics) 2. Push down outer ring to release pressure. (Heavy fabrics) 3. Insufficient pressure may cause poor feeding, skipped stitches, or difficulty in guiding the fabric.
FABRIC THREAD NEEDLE TABLE TO START SEWING Please note that the following list is a guide when sewing different fabrics. Important Hints 1. Raise the takeup lever to its highest position before starting and after stopping sewing. 2. Hold both threads about 10 cms to the rear of machine for the first two or three stitches.
TO FINISH SEAM 1 .Sew to the edge of seam. 2.Push the reverse button and sew in reverse ‘for about 3-4 cms. 3.Raise needle to its highest position. 4.Lift presser foot and pulloul the fabric to rear of machine. STRAIGHT STITCH 1 This type of stitching is the one used most frequently.
BLflTON SEWING 1 .Lower drop feed. 2. Place button attaching presser foot in position. 3.Place button between presser foot and fabric and lower presser foot. 4.Manually turn hand wheel towards you ensuring that the needle enters into both holes of button wfthout obstruction.
HEMMING Note: Hemmer foot can be purchased separately. 1. Raise the foot and the needle to its highest position. Replace the toot with the hemmer foot. 2. Fold over the fabric edge by about 3mm and place it under the foot. Secure the folded edge with a few stitches.
QUILTER Note: Quilt guide can be purchased separately. BUTTONHOLE SEWING 1.MARK WITH A PENCIL OR CHALK THE EXACT LENGTH OF THE BUTTONHOLE ON THE FABRIC. 2. REMOVE THE REGULAR PRESSER FOOT AND ATTACH THE BUTTONHOLE FOOT & PUT THE FAE UNDER ThE BUTTONHOLE FOOT.
9 U’ 5. .4 “I C, .4 CD C. 0 C z C. CD C. CD 0 -4. C. CD C. 0 CD CD C) CD DC CD CD CD C. 0. 0 CD 0 CD .4 0 ‘C 0 ‘C CD DC 0. 0 0 z ‘a, 0. DC r CD p. (fl Cl) r’ T DC 3’ .4 ,.4 ,- In -‘ .4 0 CD 0 . o 0 CD o , .C CD CD — DC DC C DC DC DC • ‘ CD CD (V DC 0 0 - 0 ‘2: .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pfaff hobby 1010 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pfaff hobby 1010 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pfaff hobby 1010 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pfaff hobby 1010 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pfaff hobby 1010, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pfaff hobby 1010.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pfaff hobby 1010. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pfaff hobby 1010 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
