Manuale d’uso / di manutenzione del prodotto IP3701H-2X del fabbricante Pelco
Vai alla pagina of 24
INST ALLA TION C2941M (8/07) IP3701H-2 and IP3701H-2X IP Color Camera.
.
C2941M (8/07) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C2941M (8/07) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
C2941M (8/07) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 C2941M (8/07) Description The IP3701H-2 and IP3701H-2X are high resolution, color video cameras with a built-in 100Base-TX network interface for live streaming to a standard Web browser (Microsoft ® Internet Explorer ® or Firefox ® ).
C2941M (8/07) 7 Basic System Configurations IMPORT ANT NOTE. PLEASE READ . The network implementations in this document are shown as general representations only and are not intended to show detailed network topologies.
8 C2941M (8/07) Figure 3. Private Network Example Figure 4. Static Network Example IF NOT DHCP , CAMERA CYCLES THROUGH IP ADDRESS RANGE 169.254.200.0 - 169.254.200.255; NETMASK 255.255.0.0 CAMERA CAMERA WEB BROWSER PRIV A TE NETWORK PC ACTS AS SERVER ( ) EXAMPLE 169.
C2941M (8/07) 9 Camera Layout Figure 5. Camera Layout RESET BUTTON Use the reset button located on the side of the camera to access the following modes: T o access one of these modes: 1. Press and hold the reset button. The unit starts cycling through the modes; hold the button for four seconds to access (cycle through) each mode.
10 C2941M (8/07) Installation LENS MOUNTING The camera can use a fixed iris, manual iris or auto iris lens. The camera is factory set for a CS-mount lens, but is easily adjusted for a C-mount lens.
C2941M (8/07) 11 Wiring T ables CAT5 CABLE Connect a Cat5 cable to the RJ-45 network connector . The 8-pin connector includes video and PoE for the camera. PoE (IEEE 802.3af) injects power over the same cabling that carries the network data, eliminating the need for a separate power supply .
12 C2941M (8/07) T able C. Recommended Wire Gauge and Wiring Distances The following are the recommended maximum distances for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.
C2941M (8/07) 13 Lens Setup and Focus Procedures VIDEO DRIVE AUTO IRIS LENS Set the lens mode selector switch to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1 Vp-p).
14 C2941M (8/07) Back Focus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case. T o adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. T urn the back focus ring until the object is in focus.
C2941M (8/07) 15 Switch Settings Figure 8. DIP Switch Default Settings NOTE: Under most conditions, no setting of switches will be required. Please read the details of each switch before making any adjustments. BLC: Back light compensation. OFF (default setting): Disables the BLC mode.
16 C2941M (8/07) Not Used EDR: Extended dynamic range • Off (Default setting): Disables the EDR mode. • EDR: Enables the EDR mode to help balance a scene with a large dynamic range. Use this feature to improve the picture in washed-out areas.
C2941M (8/07) 17 Dynamic Range and EDR Dynamic range is the ratio between the brightest and darkest parts of an image or scene. A scene that ranges from bright sunlight to deep shadows has a high dynamic range, while indoor scenes with less contrast have a low dynamic range.
18 C2941M (8/07) T roubleshooting Problem Possible Cause Suggested Remedy No video PoE power issue • V erify Cat5 cable connection. • V erify PoE is enabled. • Disconnect the Cat5 cable from the PoE and then reconnect the cable. Power is indicated by the LED.
C2941M (8/07) 19 Image too light • V erify DIP switch settings. • Use a service connector to verify camera operation. Connect one end of the service connector to the BNC service connector on the camera. Connect the other end of the service connector to a monitor .
20 C2941M (8/07) Specifications GENERAL Construction Finish Black polyester powder coat Imaging Device 1/3-inch imager Picture Elements IP3701H-2 768 (H) x 494 (V) IP3701H-2X 752 (H) x 582 (V) Sensing Area 6 mm diagonally Horizontal Resolution 480 TV lines Iris Control Electronic/passive Minimum Illumination 0.
C2941M (8/07) 21 Minimum Web Browser Requirements PC (Pentium ® 4 microprocessor , 1.6 GHz) with Windows ® 98, Windows 2000, Windows XP (or higher), or Mac ® OS X 10.3.9 (or higher) RAM 512 Mbyte Ethernet Card 100 Mbit Web Browser Internet Explorer 5.
22 C2941M (8/07) The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic c.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pelco IP3701H-2X è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pelco IP3701H-2X - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pelco IP3701H-2X imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pelco IP3701H-2X ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pelco IP3701H-2X, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pelco IP3701H-2X.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pelco IP3701H-2X. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pelco IP3701H-2X insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
