Manuale d’uso / di manutenzione del prodotto 1092 del fabbricante Patton electronic
Vai alla pagina of 19
USER MANUAL MODEL 1092 High Speed, 2-Wire, Sync & Async Short Range Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .
T ABLE OF CONTENTS Section Page 1.0 W arranty Information .............................................................2 1.1 Radio and TV Interference 1.2. CE Notice 1.3 Service Information 2.0 General Information .....................................
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor .
3.0 CONFIGURA TION The Model 1092 is equipped with two sets of eight DIP switches, which allow configuration of the unit to a wide variety of applications. The Model 1092 is also equipped with an internal switch that allows selection of 1 15 or 230 V AC power inputs (Note: this switch is not present in Models 1092-UI and 1092-DC).
Switches S1-4 and S1-5: Asynchronous/Sync Operation Use Switches S1-4 and S1-5 to configure the Model 1092 for async/sync operation. Both switches must be set in the “Off” position.
3.2 CONFIGURING THE SOFTW ARE SWITCHES The Model 1092 features a menu-driven command system that allows you to configure either the local or remote 1092.
3.2.1 Configuring the Local 1092 T o configure the LOCAL 1092, make a selection from the following MAIN MENU screen. T o configure the REMOTE 1092, type [$] (Shift- 4) and refer to Section 3.2.2 . MAIN MENU Option 1: Display Active Configuration Select Option 1 to display the most recent configuration of the local Model 1092 (See below).
1. DTE Rate Select Option 1 in the SOFTW ARE CONFIGURA TION menu to select the async. or sync. DTE Rate of the Model 1092. Different DTE Rate menu screens will display for async.
MAIN MENU Option 5: Select Hardware/Software Control Select Option 5 from the MAIN MENU selects whether the Model 1092 will use the hardware switch settings or the software switch settings for its active configuration. If Options 1 or 2 are selected, the 1092RC will use the current hardware or software switch settings as the active configuration.
MAIN MENU Option 7: T est Modes Select Option 7 from the MAIN MENU to select the test mode status of the Model 1092. (below). The Model 1092 T est Mode settings help to verify the integrity of the data link and isolate communication difficulties. NOTE: An error counter is displayed when the unit is in one of the above test modes except LLB and RDL.
3.2.2 Configuring the Remote 1092 T o configure the Remote 1092, make a selection from the following REMOTE UNIT CONFIGURA TION MAIN MENU. T o return to the LOCAL 1092 MAIN MENU screen, press [ESC] and refer to Section 3.
4.2 CONNECTION TO THE SERIAL PORT The serial port interface on the Model 1092 uses interchangeable QuikConnect™ Modules. Each QuikConnect™ Module has a 50-pin card edge connector on one side and a serial port interface on the other . Figure 4 below shows how a QuikConnect™ Module plugs into the back of the Model 1092.
Installing the New QuikConnect™ Module 1) Make sure the power switch is off. Leave the power cord plugged into a grounded outlet to keep the unit grounded. 2) Hold the module with the faceplate toward you and align the module with the guide slots in the rear panel of the Model 1092.
4.3.2 Connecting to a DC Power Source The 48 VDC power supply option uses a 3-pin terminal block with spring-type connectors. Please refer to the Model 1090 Series Service Manual for further instructions. 25 5.0 OPERA TION Once the Model 1092 is properly configured and installed, it should operate transparently .
NS Glow red to indicate that the local Model 1092 has not yet connected with the remote 5.3 TEST MODES The Model 1092 offers two proprietary loopback test modes, plus a built-in V .52 BER test pattern generator , to evaluate the condition of the modems and the communication link.
2. If the above test indicates no errors are present, move the V .52 toggle switch DOWN, activating the “51 1/E” test with errors present. If the test is working properly , the local modem's red “ER” LED will glow .
APPENDIX B P A TTON MODEL 1092 F ACTOR Y REPLACEMENT P ARTS AND ACCESSORIES Patton Model # Description IM1/A ...............................V .24 with DB25F IM1/B ...............................RS422/RS530 with DB25F IM1/C ............................
APPENDIX C P A TTON MODEL 1092 INTERF ACE PIN ASSIGNMENT (Continued) V .35 Interface (M/34F Female Connector) (DCE Configuration) Pin # Signal B ...........................SGND (Signal Ground) C ...........................R TS (Request to Send) D ....
APPENDIX D P A TTON MODEL 1092 Pin Out Control Port The 1092 control port is an 8 position connector , compliant with EIA/TIA-561. Pin Function RJ45 Pin No. Ground 4 Receive data (to DTE) 5 T ransmit data (from DTE) 6 35 Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your business.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Patton electronic 1092 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Patton electronic 1092 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Patton electronic 1092 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Patton electronic 1092 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Patton electronic 1092, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Patton electronic 1092.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Patton electronic 1092. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Patton electronic 1092 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
