Manuale d’uso / di manutenzione del prodotto PTR3E del fabbricante Panduit
Vai alla pagina of 59
PTR3E Thermal Transfer Printer Operator and Technical Reference Manual.
Panduit PTR3E Panduit Corp. Identification Products Division 1819 Atlanta Hwy. Cumming, GA 30040-1069 Phone: 888-506-5400 Fax: 770-889-9264 Copyright © Panduit Corp.
This manual will guide you step by step in the set-up, operation, and troubleshooting of the PTR3E Printer. If you have problems not covered call Technical Support at 1-888-506-5400, ext. 7470. SAFETY PRACTICES The following general safety practices supplement the specific warnings and cautions elsewhere in this manual.
INFORMATION TO USER NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PREFACE PTR3E OPERATOR MANUAL The PTR3E Operator Manual contains basic information about the printer such as setup, installation, cleaning and maintenance. It also contains complete instructions on how to use the operator panel to configure the printer.
TABLE OF CONTENTS SECTION 1. PRINTER OVERVIEW Introduction ..............................1 General Printer Specifications ....................2 - 3 Character Fonts ............................4 B a r C o d e s ...............................5 Physical .
SECTION 5. INTERFACE SPECIFICATIONS IEEE1284 Parallel Interface .....................4 7 RS232C Serial Interface .......................4 8 SECTION 6. TROUBLESHOOTING Initial Checklist ............................4 9 Using the IEEE1284 (Parallel) Interface .
.
SECTION 1. PRINTER OVERVIEW INTRODUCTION The Panduit PTR3E Thermal Transfer Printer is a complete, high-performance on-site labeling system. All printer parameters are user programmable using the front panel controls and the DIP switches.
GENERAL PRINTER SPECIFICATIONS 2 Section 1. Printer Overview SPECIFICATION PTR3E PRINT Method Direct or Thermal Transfer Speed (User Selectable) 2 to 10 ips 50 to 250 mm/s Print Module (Dot Size) .0049 in. .125 mm Resolution 203 dpi 8 dpmm Maximum Print Width 4.
3 Section 1. Printer Overview SPECIFICATION PTR3E CONTROLS AND SIGNALS On-Line Green LED Power Green LED Label Red LED Ribbon Red LED Error Red LED LCD Panel 2 Line x 16 Character On/Off-Line Switch F.
CHARACTER FONTS 4 Section 1. Printer Overview SPECIFICATION PTR3E MATRIX FONTS U Font (5 dots W x 9 dots H) S Font (8 dots W x 15 dots H) M Font (13 dots W x 20 dots H) XU Font (5 dots W x 9 dots H) H.
BAR CODES 5 Section 1. Printer Overview SPECIFICATION PTR3E SYMBOLOGIES Bookland (UPC/EAN Supplemental) EAN-8, EAN-13 CODABAR Code 39 Code 93 Code 128 Interleaved 2 of 5 Industrial 2 of 5 Matrix 2 of .
PHYSICAL 6 Section 1. Printer Overview SPECIFICATION PTR3E DIMENSIONS Wide 10.4 in. (265 mm) Deep 17.1 in. (435 mm) High 13.4 in. (341 mm) WEIGHT 39.6 lbs (18 Kg) POWER REQUIREMENTS Voltage 100 - 115 .
SECTION 2. INSTALLATION INTRODUCTION This section will assist you in taking the PTR3E from the shipping container to the application environment. The following information is provided in this section:.
UNPACKING AND PARTS IDENTIFICATION Consider the following when unpacking the printer: • The box should stay right-side up. • Lift the printer out of the box carefully. • Remove the plastic covering from the printer. • Remove the accessory items from their protective containers.
Verify that you have the following materials when unpacking: • Printer • Power Cord • Extra Ribbon Core • Operator and Technical Reference Manual SETTING UP THE PRINTER Consider the following when setting up the printer: • Locate a solid flat surface with adequate room to set the printer.
.
LOADING LABELS Follow these steps to properly load labels into the PTR3E: 1. Open the Top Access Door by swinging it up and to the left. Open the Side Access Door by swinging it to the rear of the printer. 2. Open the Print Head Assembly by pushing the Head Latch toward the rear of the printer.
5. If using roll labels (or tags), load the roll onto the Label Supply Spindle so that the printing side of the labels faces upwards as it unwinds from the roll. Push the roll all the way to the inside of the printer and push the Label Roll Retainer snugly against the outside of the label roll.
11. Adjust the outside Label Edge Guide until it touches the outside edge of the label and tighten the thumb screw. Make sure the labels are also touching the inside edge guides. 12. If the ribbon is already loaded, close the Print Head by rotating the black Head Latch toward the front of the printer until it latches closed.
LOADING THE RIBBON 1. Open the Top Access Door by swinging it up and to the left and the Side Access Door by swinging it toward the rear of the printer. 2. Open the Print Head by rotating the Head Latch toward the rear of the printer. The Print Head is spring-loaded and will automatically open as soon as the Head Latch is disengaged.
6. Load the ribbon behind and over the top of the Ribbon Rewind Spindle and tape it to the Extra Ribbon Core . Make sure it matches the ribbon path shown in the diagram. 7. Manually turn the Rewind Spindle to wrap the ribbon onto the core one to two turns to secure it.
OPERATOR PANEL The PTR3E Operator Panel consists of five LED indicators, two momentary contact switches, two DIP switches, four adjustment potentiometers and one LCD Display. All of these are accessible from the front of the printer. They are used to set the printer operating parameters and to indicate the status of the printer to the operator.
Pause.
REAR PANEL Fuse EXT Port Connector Parallel Port Connector Memory Card Option Fan Fold Access Panel AC Power In.
SWITCHES AND SENSORS.
LABEL SENSOR ADJUSTMENT The Label Sensor Assembly can be positioned to match the location of the label registration hole/gap/edge. The diagram below illustrates the relative position of each sensor along the Label Sensor Unit and its range of movement.
SECTION 3. CONFIGURATION PRINTER DIP SWITCH CONFIGURATION DIP Switch P anels There are two DIP switches (DSW2 and DSW3) located underneath a snap-on cover on the front panel.
Head Check Selection (DSW2-3) . When selected, the printer will check for head elements that are electrically malfunctioning. Hex Dump Selection (DSW2-4) . Selects Hex Dump mode (see page 37). Receive Buffer Selection (DSW2-5) . Selects the operating mode of the receive buffer.
Print Speed Adjustment (DSW2-8) . See page 27. Mode Selection (DSW3-1 and DSW3-2) . Selects the operating mode of the printer. Batch/Continuous disables the label taken (dispense option) sensor. Label Sensor Selection (DSW3-3) . Enables or disables the Label Pitch Sensor.
External Signal Type Selection (DSW3-6, DSW3-7) . Selects the type of output signal. Repeat Print via External Signal (DSW3-8) . Allows an external device to control the reprint of the label in the print buffer. RS232 Transmit/Receive Setting (located on RS232C I/F Module) The PTR3E comes standard with a parallel port only.
Baud Rate Selection (DSW1-5, DSW1-6) . Selects the data rate (bps) for the RS232 port. Protocol Selection (DSW1-7, DSW1-8 ) . Selects the flow control and status reporting protocols. See Section 4: Interface Specifications for more information. Default Settings Switch Selections - All switches are placed in the OFF position (default) for shipping.
PRINTER ADJUSTMENTS The LCD Panel on the PTR3E is used in conjunction with the LINE and FEED switches by the operator to manually enter printer configuration settings.
Normal Mode The printer initially powers on in the ONLINE mode. The user can access the User Settings using the following procedures: Display lists the current ROM version of the printer during the initialization process. The LCD will display the ONLINE status on the top line and the bottom line will contain the label quantity (QTY) status.
The label Pitch distance from the leading edge (the edge that comes out ofthe printer first) of a label and the leading edge of the next label. The leading edge position of the label can be adjusted relative to the print head +/- 49 mm in increments of 1mm.
If the printer has print job(s) in memory, selecting YES will cause the job(s) to be cleared. The default selection is number Be sure you want to cancel the print job(s) before selecting yes as the job(s) cannot be recovered and will have to be retransmitted to the printer.
2. Once the correct setting is underlined, pressing the FEED key will accept the setting and advance the display to the Print Offset display. Vertical Offset is the distance down from the leading edge (the edge of the label that comes out of the printer first) to the first vertical print position.
This selection allows you to set the default character pitch to either fixed character spacing or proportional character spacing. 1. Use the LINE key to step the underline cursor to the desired setting. 2. Once the correct setting is underlined, pressing the FEED key will accept the setting and advance the display.
This selection specifies whether or not the printer will automatically feed a blank label when it is placed in the Online mode. 1. Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will feed a blank label anytime it enters the Online mode.
This selection allows the user to assign a priority for Print Darkness, Print Speed and Print Offset. 1. Use the LINE key to step to the desired priority. If LCD is selected, the setting established via the LCD display/menu system will be used for an incoming label job, regardless of any different command settings.
DEFAULT SETTING MODE Occasionally it is desirable to reset all printer configuration settings to their original default conditions. This allows the operator to start reconfiguration of the printer starting from a known set of conditions.
4. If the printer did not beep and print a status label, turn the printer off and check your data stream for errors and start the download process over. 5. If the custom codes are correct, press the FEED key to accept them and terminate the download process.
have enough range, then you will have to change the pitch setting using the LCD front panel display. 6. Press the FEED key to stop the printer. 7. To exit the Test Label mode, power the printer off and then back on. Adjusting the PITCH potentiometer will affect the stop position of the label.
DISPLAY COUNTER VALUES The internal counters are used to track the number of kilometers of media that has been processed through the printer, the number of labels cut and/or the number of label dispensed. These values can be used to track component life for service and maintenance functions.
.
SECTION 4. CLEANING AND MAINTENANCE INTRODUCTION This section provides information on user maintenance for the PTR3E. This section contains the following information.
Print Potentiometer The fine adjustment for Print Darkness is the PRINT potentiometer on the operator panel. It provides a continuous range of adjustment, allowing you to make precise changes. Use a small cross-point screwdriver, turning clockwise for darker print and counterclockwise for lighter print.
CLEANING THE PRINT HEAD, PLATEN AND ROLLERS Supplies Needed: PTR-CLN printer cleaning kit Includes: 4 oz. (116 ml) bottle cleaning solution with MSDS, cleaning pens, 100 swabs, 12 alcohol wipes and instructions Cleaning the Print Head and Platen 1. Turn the printer OFF and remove the power cable.
Cleaning the Rollers and Guides 1. The Label Load Drive is located underneath the Label Hold-Down .I t should be cleaned of any label residue or foreign material. The Label Hold Down Roller is located on the underneath side of the Label Hold Down . It should also be cleaned of any residue or foreign material.
REPLACING THE PRINT HEAD The print head on the PTR3E printer is a user-replaceable item. If it becomes damaged for any reason, it can be easily removed and replaced. Contact Technical Support for information on obtaining a new print head. Supplies needed: No.
6. View the Print Head from the front of the printer. Locate the center mounting screw on the top of the assembly. Unscrew this screw and set it aside. 7. The Print Head should now be loosened from the top of the assembly by grasping either side and carefully pulling it down.
REPLACING THE FUSE Supplies needed: 250V 3A Fuse 1. Turn the printer power OFF and remove the power cable. 2. On the back of the printer, locate the Fuse Cap on the right-hand side of the AC connector. 3. Unscrew the cap and remove the defective fuse.
46 Section 4: Cleaning and Maintenance.
SECTION 5. INTERFACE SPECIFICATIONS INTERFACE TYPES The parallel interface for the PTR3E printer is a high speed, bi-directional interface that conforms to the IEEE1284 specification (ECP mode on some computers). The interface is also compatible with the older Centronics parallel interface standard.
RS232C SERIAL INTERFACE The High Speed Serial Interface is a Plug-In Interface Module. The PTR3E comes standard with parallel interface. GENERAL SPECIFICATIONS Asynchronous ASCII Half-duplex communica.
SECTION 6. TROUBLESHOOTING This section has been compiled to help you produce output on the PTR3E. Use this section to make sure the basics have been checked before deciding you are unable to proceed any further.
5. When you send the print job to th eprinter, and it does not respond, do you get an error message on your PC that says “Device Fault” or something similar? This may mean that the computer doesn’t know the printer is there. Verify that: a. Both ends of the cable are securely inserted into their respective connectors.
ERROR SIGNALS LED LCD MESSAGE AUDIBLE BEEP ERROR CONDITION TO CLEAR Error On Machine Error 1 Long Machine Error Cycle power on/off Error On EEPROM Error 1 Long EEPROM Read/Write Cycle power on/off Err.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Panduit PTR3E è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Panduit PTR3E - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Panduit PTR3E imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Panduit PTR3E ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Panduit PTR3E, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Panduit PTR3E.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Panduit PTR3E. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Panduit PTR3E insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
