Manuale d’uso / di manutenzione del prodotto NP03CM del fabbricante NEC
Vai alla pagina of 16
Portable Projector NP03CM Ceiling Mount Unit Installation and Adjustment Manual Thank you for your purchase of the NEC portable projector ceiling mount unit. Please read this installation and adjustment manual carefully to ensure proper use. Special skills are required for the installation of the portable projector.
2 Heed the Follo wing • When installing the projector, be sure to do so as explained in this manual. The projector may fall and cause injury if it is installed improperly. • To prevent the projector from falling, install it in a place and fasten it in a way with sufficient strength to support the combined weight (4.
3 CA UTION • Do not obstruct the projector's ventilation holes. Doing so will prevent the dissipation of heat and may result in fires. In particular, do not use the projector in the following ways: Do not install the projector in a wall or in a tight place where ventilation is poor, place a cover it, etc.
4 • Distance to lens end Center line of fixed ceiling part Lens center 70 105.2 162.5 90 90 60 60 80.4 10 4 - Preparation List of P acka ged Parts Fixed ceiling part ...1 Projector mounting adapter ...1 Projector mounting screws (M 4)...3 Up-down angle adjustment screws (M5 ) .
5 Zoom adjustment range 25 0123456789 1 0 12(m) 40 60 80 100 120 150 180 200 240 300 11 Wide angle (Maximum) Telephoto (Maximum) Guide to Screen Size and Projector Mounting Position Screen Size and Pr.
6 Guide to Screen Size and Projector Mounting Position 25 01234567 8 9 1 0 11(m) 40 60 80 100 120 150 180 200 240 300 （ 型 ） Screen Size and Projection Distance···VT48/VT49 Use this guide when considering the distance to the screen and the screen size.
7 Guide to Screen Size and Projector Mounting Position Zoom adjustment range 25 0123456789 1 0 12(m) 40 60 80 100 120 150 180 200 240 300 11 Telephoto (Maximum) Wide angle (Maximum) Screen Size and Projection Distance···VT695 Use this guide when considering the distance to the screen and the screen size.
Guide to Screen Size and Projector Mounting Position 8 (m) 25 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0m 40 60 80 100 120 150 180 200 240 270 300 (Inches).
9 1 Mounting the Pr ojector Attach the Fixed Ceiling P ar t to the Ceiling First, partially tighten the four screws, then tighten the screws firmly after positioning. Use M8 bolts for the fixed ceiling part. Use of types other than M8 could cause the projector to fall.
10 3 4 Mounting the Projector Suspend the Projector fr om the Fixed Ceiling P ar t Slide the slotted part of the projector mounting adapter over the pin of the fixed ceiling part and push all the way to the back.
Mounting the Projector 11 NOTE : Mounting boards, M8-type anchor nuts, bolts, nuts and washers are commercially available. Mounting board (Strong enough to support the weight of the whole unit.
12 1 2 3 Replacing the Lamp To replace the lamp, first switch off the power, wait for the cooling fans to stop and disconnect the power plug from the outlet. Now, wait about 60 minutes before replacing the lamp. Attempts to replace the lamp during operation or immediately after operation has stopped will cause burns because of the high temperature.
13 1 10 ˚ 10 ˚ 上下端 Upper and lower edges Adjustment of the Pr ojection Angle Before the Adjustment • Refer to the instruction manual of the projector, switch on the power and project an image. • Refer to the section "Orientation " of Setup and select the projection orientation.
10 ˚ 1 0 ˚ 14 Left and right edges 10 ˚ 10 ˚ 2 3 Adjustment of the Projection Angle Adjust the Up-Down Angle Turn the projector up and down so that the left and right edges of the screen are parallel, then firmly tighten the four up-down angle adjustment screws.
15 Adjustment of the Projection Angle Fine Adjustment After the adjustments, chec k that the par ts are fixed securel y . Loosen the same screws that were used in the distortion adjustment and finely adjust the angle so that the projected image fits the screen, then tighten all the screws (i.
MEMO NP03CM_E 07.3.12 2:15 PM ページ 16.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il NEC NP03CM è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del NEC NP03CM - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso NEC NP03CM imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul NEC NP03CM ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il NEC NP03CM, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del NEC NP03CM.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il NEC NP03CM. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo NEC NP03CM insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
