Manuale d’uso / di manutenzione del prodotto SP303530 del fabbricante Multiquip
Vai alla pagina of 123
OPERATION AND PARTS MANUAL SP3 “STREET PRO” PROFESSIONAL SLAB SAW 35 HP WISCONSIN DIESEL ENGINE MODELS SP303516, SP303520, SP303526 SP303530 Revision #3 (09/29/06) THIS MANUAL MUST COMPANY THE EQUIPMENT AT ALL TIMES. Diamond Back To find the latest revision of this publication, visit our website at: www.
.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 1 MQ SP-3035 CONCRETE SAW P ROPOSITION 65 W ARNING.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 2 MQ SP-3035 CONCRETE SAW S ILICOSIS /R ESPIRATORY HAZARDS Grinding/cutting/drilling of masonry , concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 3 MQ SP-3035 CONCRETE SAW Table of Contents PROPOSITION 65 WARNING .......................................................................................1 SILICOSIS /RESPIRATORY HAZARDS .
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 4 MQ SP-3035 CONCRETE SAW MAINTENANCE .............................................................................................................40 R EMOVABLE G UARDS AND A CCESS P ANELS .
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 5 MQ SP-3035 CONCRETE SAW P ULLEY AND V-B ELT A SSY . ........................................................................................ 101 B ATTERY A SSY .
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 6 MQ SP-3035 CONCRETE SAW www .m ultiquip .com Best Deal! Note: Discounts Are S ubject To Change Note: Discounts.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 7 MQ SP-3035 CONCRETE SAW SAFETY FOR YOUR SAFETY AND THE SAFETY OF OTHERS ! NOTE This Owner's Manual has been developed to provide instruct ions for the safe and efficient operation of the Multiquip SP-3035 CONCRETE SAW.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 8 MQ SP-3035 CONCRETE SAW HAZARD SYMBOLS Explosive Fuel Gasoline is extremely flammable, and its vapors can cause an explosion if ignited. DO NOT start the engine ne ar spilled fuel or combustible fluids.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 9 MQ SP-3035 CONCRETE SAW HAZARD SYMBOLS Over Speed NEVER tamper with factory settings of engi ne governor or speed settings. Ensure the proper Speed Kits are in stalled to safely support the prescribed RPM settings for diamond blade operations.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 10 MQ SP-3035 CONCRETE SAW HAZARD SYMBOLS Skin Injection Hazard NEVER use your hand to find hydraulic leaks.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 11 MQ SP-3035 CONCRETE SAW General Safety Warnings Most accidents involving product operation, main tenance and repair are caused by failure to observe basic safety rules and precautions.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 12 MQ SP-3035 CONCRETE SAW General Safety Warnings WARNING ALWAYS read, understand, and follow procedures in the Operator’s Manual before attempting to operate the equipment.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 13 MQ SP-3035 CONCRETE SAW BLADE SAFETY WARNING ALWAYS inspect diamond blades before each use. The blade should exhibit no cracks, dings, or flaws in the steel centered core and/or rim.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 14 MQ SP-3035 CONCRETE SAW SAW TRANSPORTATION SAFETY WARNING Use appropriate lifting equipment to ensure the safe movement of the saw. DO NOT use the handle bars and/or front poi nter as lifting points.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 15 MQ SP-3035 CONCRETE SAW MACHINE OPERATION AND SAFETY DECALS The Multiquip SP-3035 Saw is equipped with a nu mber of operation and safety decals. Should any of these decals become unreadable, replacements can be obtained from your dealer.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 16 MQ SP-3035 CONCRETE SAW Serial Tag Fig. 2 — Serial Tag NOTE For future reference, fill in th e model number and serial number of your saw in the space above.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 17 MQ SP-3035 CONCRETE SAW O PERATION Before Starting Walk around the saw and ensure that all guards and panels are properly installed. Wear eye and hearing protection.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 18 MQ SP-3035 CONCRETE SAW Control Panel Fig. 5 — The Control Panel Auxiliary Switch Voltmeter T hrottle Engin.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 19 MQ SP-3035 CONCRETE SAW Engine Power, Cutting Power & Sheave Size Blade Size & Configuration per Model The SP-3035 is available in four Blade Speed co nfigurations.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 20 MQ SP-3035 CONCRETE SAW Installing the Blade, Blade Guard & Blade Flange Remain Clear of all parts of saw while installing blade to prevent crush injury or death.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 21 MQ SP-3035 CONCRETE SAW Removing the Blade, Blade Guard & Blade Flange Remain Clear of all parts of saw while installing blade to prevent crush injury or death.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 22 MQ SP-3035 CONCRETE SAW Stacking Blades for Wide Cuts Remain Clear of all parts of saw while installing blade to prevent crush injury or death. Verify the engine start switch is OFF before installing blade.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 23 MQ SP-3035 CONCRETE SAW Installing and Removing the Blade Guard Blade Guards for the SP-3035 concrete saw can be installed on either side of the saw. Verify the engine start switch is OFF before installing blade.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 24 MQ SP-3035 CONCRETE SAW Removing the Blade Guard During use, the Blade Guard can become tight on th e tapered mounting tab. To loosen it, wiggle the Rear Blade Guard Handle up and down , while lifting with the Top Handle.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 25 MQ SP-3035 CONCRETE SAW Installing the Flange Guard The Flange Guard provides protection from the Blade Flange not in use. 1. Verify that the unused Blade Flan ge is secured to the Spindle by tightening the mounting bolt.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 26 MQ SP-3035 CONCRETE SAW Water Supply and Control WARNING To prevent damage to the impeller of a belt driven water pum p , do not run the engine with the water pump switch on, unless the water supply is connected and water is flowing.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 27 MQ SP-3035 CONCRETE SAW Handlebars The handlebars are adjustable to three different angles, for optimum operator control, and can also be slid fully inward for storage.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 28 MQ SP-3035 CONCRETE SAW Fueling the Saw The 3000 Series saws feature a five-gallon clear molded plastic fuel tank with a sight gauge, central drain, and shutoff valve.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 29 MQ SP-3035 CONCRETE SAW Starting and Stopping the Engine WARNING Do not leave the saw unattended while the engine is running. Do not start, park, or leave the saw unattended on a slope.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 30 MQ SP-3035 CONCRETE SAW Pointer Adjustment 1. Lower the front pointer assembly: Release the ro pe from the cam cleat, and rotate the pointer forward into position.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 31 MQ SP-3035 CONCRETE SAW Raise – Lower Controls This saw uses a 12-volt hydraulic pump and cylinde r to raise and lower the blade. Controls are located on the speed control joystick handle.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 32 MQ SP-3035 CONCRETE SAW Setting the Depth Gauge & Depth Stop The 3000 Series saws use a cable-controlled Depth Gauge and mechanical Depth Stop to lock the blade at the desired cut depth.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 33 MQ SP-3035 CONCRETE SAW Drive System The 3000 Series saws have a cable-controlled Hy dro-Gear hydrostatic powered transaxle with fully adjustable F-N-R (Forward-Neutral-Reverse) speed adjustment via a joystick control handle.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 34 MQ SP-3035 CONCRETE SAW Drive System Controls The control handle controls FORWARD-NEUTRAL-RE VERSE (F-N-R) speeds and the raising and lowering of the saw. To increase forward speed, slowly move the joystick FORWARD.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 35 MQ SP-3035 CONCRETE SAW Positraction Positraction, when ON, locks bo th drive wheels together for straight-line movement. It is recommended for all cutting and is especially he lpful on uneven surfaces, and when loading and unloading the saw.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 36 MQ SP-3035 CONCRETE SAW Transaxle The hydrostatic-powered transaxle has no chains, sprockets or gearboxes to service. There is a simple cable control for forward-reverse motion, an d a single drive belt from th e engine to power the transaxle.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 37 MQ SP-3035 CONCRETE SAW Transportation Tie-downs and Lift Point Tie-downs The saw is provided with holes at each corner of the lower frame for easy tie-down during transportation.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 38 MQ SP-3035 CONCRETE SAW Operation on a Slope or Incline Never operate, cut, or face the saw down a slope or incline. The weight of the saw will shift to the front wheels allowing the rear wheels to skid or come completely off the ground.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 39 MQ SP-3035 CONCRETE SAW If an attempt is made to start the saw with the bl ade pinched, the starter will suffer damage. If an attempt is made to use the lift pump to raise the saw to free the blade, the lift motor and front axle could be damaged.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 40 MQ SP-3035 CONCRETE SAW M AINTENANCE This saw has many service-saving features, such as fully enclosed oil bath lubricated Spindle bearings, which require no daily lubrication.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 41 MQ SP-3035 CONCRETE SAW Belts and Pulleys Belt Qty Part Number Spindle Drive Belt (POWERBA ND) 1 520006 Transaxle Drive Belt 1 521005 Engine to Jack shaft Drive Belt 1 521005 Fig.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 42 MQ SP-3035 CONCRETE SAW Spindle (Blade Shaft) Driv e Belt Tension Adjustment NOTE When loosening driv e belts, lower the saw to reduce stress on the tensioning system, and use gravity to pul l the engine forward slightl y.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 43 MQ SP-3035 CONCRETE SAW 4. Loosen the Outer Jam Nut on the Single Point Belt Tension Bolt. Turn the Inner Jam Nut counter-clockwise. 5. Adjust drive belt to desired tension.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 44 MQ SP-3035 CONCRETE SAW Replacing the Jack Shaft Belt WARNING NEVER attempt to check or adjust the V-belt tension with the engine running. Severe injury can occur.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 45 MQ SP-3035 CONCRETE SAW Blade Flange Removal/Installation Correct removal or installation of the Inner Bl ade Flange or Flange requires a Flange Puller (option Part Number 18503) as shown below.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 46 MQ SP-3035 CONCRETE SAW DANGER Ensure the Outer Flange is in place to prevent the Puller and Inner Flange fro.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 47 MQ SP-3035 CONCRETE SAW 6. Loosen the Mounting Bolt and remo ve the Outer Flange and Bushing. 7. Inspect the Inner Flange to ensure the proper seating of the tapered fit.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 48 MQ SP-3035 CONCRETE SAW Spindle Replacement NOTE To assure correct Spindle/Wheel al ignment it is r ecommended that this operation be performed by a Mu lt iquip Authorized Service Cen ter.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 49 MQ SP-3035 CONCRETE SAW Fig. 35 — Spindle Replacement 7. Remove the Spindle. DO NOT unbolt the Spindle Mounting Blocks , as they have been factory-installed for correct Spindle/wheel alignment.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 50 MQ SP-3035 CONCRETE SAW Circuit Breakers Three thermal circuit breakers are located behind the Control Panel access cover.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 51 MQ SP-3035 CONCRETE SAW Lubrication This saw has six grease fittings. Locations are sh own in Figure 38 on the front axle assembly, and one, (not shown) on the Jackshaft assembly.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 52 MQ SP-3035 CONCRETE SAW Engine Maintenance The Model SP-3035 uses a 35 HP Wisconsin engine. See the engine manual for service details. Check air filters daily.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 53 MQ SP-3035 CONCRETE SAW Raise-Lower System This saw uses a 12-volt hydraulic pump an d cylinder to power the raise-lower system. Level the frame prior to service to get accurate readings.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 54 MQ SP-3035 CONCRETE SAW Control Handle Adjustment The Control Handle is adjustable to provide the preferred “feel”. 1. Using a ¼” Allen wrench and 9/16” wrench, loosen both pivot bolts until they can be turned by hand.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 55 MQ SP-3035 CONCRETE SAW Hydraulic System The hydraulic system consists of: Spindle Assembly (1) Hydraulic Pum.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 56 MQ SP-3035 CONCRETE SAW Draining & Filling the Hydraulic System To drain the Transaxle 1. Remove the drain plug from the bottom of the Spindle housing and the bottom of the Transaxle.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 57 MQ SP-3035 CONCRETE SAW Fig. 44 — Spindle Assembly 1. Raise the saw 2/3 or more up. 2. Remove the drain plug from the bottom of the Spindle housing. 3. Re-install the drain plug and install a new oil filter.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 58 MQ SP-3035 CONCRETE SAW Drive Wheel Alignment Below is the suggested technique for aligning the wheels. Distance X is the same on either side; the Front Axle and Spindle must be at right angles to the frame edge.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 59 MQ SP-3035 CONCRETE SAW The drive wheels are aligned by adjust ing the entire rear drive assembly. 1. Raise the saw halfway, then lift the rear of the saw until flanges touch the ground.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 60 MQ SP-3035 CONCRETE SAW Positraction Adjustment Fig. 47 — Positraction Adjustment Bolt Locations 1. Lift Saw 4” to 6” and tilt forward to place spin dle flanges on ground.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 61 MQ SP-3035 CONCRETE SAW EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual.
MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 62 MQ SP-3035 CONCRETE SAW SUGGESTED SPARE PARTS MQ SP-3035 CONCRETE SAW WITH WISCONSIN 35 HP AIR-COOLED DIESEL ENGINE 1 to 3 Units Qty. P/N Description 1 ........
MQ SP-3035 Concrete Saw — Name p late and Decals MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 63 C OMPONENT D RAWINGS Nameplate and Decals Assy. The Multiquip SP-3035 Saw is equipped wit h a number of operation and safety dec als.
MQ SP-3035 Concrete Saw — Name p late and Decals MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 64 Nameplate and Decals Assy .
MQ SP-3035 Concrete Saw — Deck/Gau g e Panel Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 65 Deck/Gauge Panel Assy.
MQ SP-3035 Concrete Saw — Deck/Gau g e Panel Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 66 Deck/Gauge Panel Assy.
MQ SP-3035 Concrete Saw — Console/Sheet Metal Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 67 Console/Sheet Metal Assy.
MQ SP-3035 Concrete Saw — Console/Sheet Metal Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 68 Console/Sheet Metal Assy .
MQ SP-3035 Concrete Saw — Access Panel Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 69 Access Panel Assy.
MQ SP-3035 Concrete Saw — Access Panel Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 70 Access Panel Assy .
MQ SP-3035 Concrete Saw — Fuel Tank Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 71 Fuel Tank Assy.
MQ SP-3035 Concrete Saw — Fuel Tank Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 72 Fuel Tank Assy .
MQ SP-3035 Concrete Saw — F-N-R Control Handle Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 73 F-N-R Control Handle Assy.
MQ SP-3035 Concrete Saw — F-N-R Control Handle Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 74 F-N-R Control Handle Assy . NO PART NO PART NAME QTY . REMARK 1 560030 F-N-R CONTROL HANDLE ASSY. .....
MQ SP-3035 Concrete Saw — Jo y stick Mountin g Ass y . MQ SP-3035 CONCRETE SAW — MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 75 Joystick Mounting Assy.
MQ SP-3035 Concrete Saw — Jo y stick Mountin g Ass y . MQ SP-3035 CONCRETE SAW — MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 76 Joystick Mounting Assy . NO PART NO PART NAME QTY. REMARK 1# 0161D NUT, HEX FINISH 5/16-18 2 2# 10019 NUT, FYLOC #10-32 1 3# 1579 SCREW.
MQ SP-3035 Concrete Saw — Lift Pum p Circuit Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 77 Lift Pump Circuit Assy.
MQ SP-3035 Concrete Saw — Lift Pum p Circuit Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 78 Lift Pump Circuit Assy .
MQ SP-3035 Concrete Saw — Water S y stem Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 79 Water System Assy.
MQ SP-3035 Concrete Saw — Water S y stem Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 80 Water System Assy .
MQ SP-3035 Concrete Saw — De p th Indicator Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 81 Depth Indicator Assy.
MQ SP-3035 Concrete Saw — De p th Indicator Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 82 Depth Indicator Assy . NO PART NO PART NAME QTY. REMARK 1 125032 DEPTH INDICA TOR U-BRACKET 1 2 110031 POINTER, DEPTH 1 3 560025 KNOB, COMFORT GRIP 1 4 460019 FLANGE BEARING, .
MQ SP-3035 Concrete Saw — Handle and Li g ht Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 83 Handle and Light Assy.
MQ SP-3035 Concrete Saw — Handle and Li g ht Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 84 Handle and Light Assy .
MQ SP-3035 Concrete Saw — Front/Rear Pointer Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 85 Front/Rear Pointer Assy.
MQ SP-3035 Concrete Saw — Front/Rear Pointer Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 86 Front/Rear Pointer Assy . NO PART NO PART NAME QTY. REMARK 1# 120045 RIGHT SIDE POINTER 1 2# 120046 LEFT SIDE POINTER 1 3# 25832 ROPE ASSY.
MQ SP-3035 Concrete Saw — Gau g es and Controls Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 87 Gauges and Controls Assy.
MQ SP-3035 Concrete Saw — Gau g es and Controls Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 88 Gauges and Controls Assy . NO PART NO PART NAME QTY. REMARK 1 15171 CABLE PULL 1 2 446004 VALVE, WATER FLOW CONTROL 1 3 25627 F-N-R CONTROL ASSY.
MQ SP-3035 Concrete Saw — Front Axle Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 89 Front Axle Assy.
MQ SP-3035 Concrete Saw — Front Axle Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 90 Front Axle Assy .
MQ SP-3035 Concrete Saw — De p th Sto p Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 91 Depth Stop Assy.
MQ SP-3035 Concrete Saw — De p th Sto p Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 92 Depth Stop Assy . NO PART NO PART NAME QTY. REMARK 1 35120 DEPTH STOP LEAD SCREW 1 2 933244 WASHER, FLAT SAE 1/2 3 3 565002 SPRING, COMPRESSION, 7/8 1 4 582009 COLLAR, SET .
MQ SP-3035 Concrete Saw — Platform Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 93 Platform Assy..
MQ SP-3035 Concrete Saw — Platform Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 94 Platform Assy . NO PART NO PART NAME QTY. REMARK 1 25807 PLATFORM 1 3 924287 SCREW, FHSC, 3/8-16 X 1-1/4,NP 6 4 120038 CLIP, MOUNT,BLADEGUARD 1 5 120040 SPACER, BLADEGUA RD CLIP, .
MQ SP-3035 Concrete Saw — Drive Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 95 Drive Assy..
MQ SP-3035 Concrete Saw — Drive Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 96 Drive Assy . NO PART NO PART NAME QTY. REMAR K 1 263002 TRANSAXLE ASSY. ..............................................
MQ SP-3035 Concrete Saw — Bladeshaft and Mountin g Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 97 Bladeshaft and Mounting Assy.
MQ SP-3035 Concrete Saw — Bladeshaft and Mountin g Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 98 Bladeshaft and Mounting Assy . NO. PART NO. PART NAME QTY. REMARKS 1 35270 BLADESHAFT AND MOUNTING GROUP .
MQ SP-3035 Concrete Saw — Positraction Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 99 Positraction Assy.
MQ SP-3035 Concrete Saw — Positraction Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 100 Positraction Assy .
MQ SP-3035 Concrete Saw — Pulle y and V-Belt Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 101 Pulley and V-Belt Assy.
MQ SP-3035 Concrete Saw — Pulle y and V-Belt Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 102 Pulley and V-Belt Assy . NO PART NO PART NAME QTY. REMARKS 1 540006 PULLEY, BLADESHAFT 3.8 6G 3VX1615 ..
MQ SP-3035 Concrete Saw — Batter y Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 103 Battery Assy..
MQ SP-3035 Concrete Saw — Batter y Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 104 Battery Assy .
MQ SP-3035 Concrete Saw — En g ine Brackets Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 105 Engine Brackets Assy.
MQ SP-3035 Concrete Saw — En g ine Brackets Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 106 Engine Brackets Assy . NO PART NO PART NAME QTY. REMARK 1 125034 LIFTING RING 1 2 933242 WASHER, FLAT SAE 3/8 GRD 9 YZ 4 3 915105 SCREW, HHC 3/8-16 X 1.
MQ SP-3035 Concrete Saw — En g ine Installation Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 107 Engine Installation Assy.
MQ SP-3035 Concrete Saw — En g ine Installation Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 108 Engine Installation Assy .
MQ SP-3035 Concrete Saw — Blade g uard Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 109 Bladeguard Assy.
MQ SP-3035 Concrete Saw — Blade g uard Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 110 Bladeguard Assy .
MQ SP-3035 Concrete Saw — O p tional Water Pum p Kit Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 111 Optional Water Pump Kit Assy.
MQ SP-3035 Concrete Saw — O p tional Water Pum p Kit Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 112 Optional Water Pump Kit Assy .
MQ SP-3035 Concrete Saw — Collar Puller Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 113 Collar Puller Assy.
MQ SP-3035 Concrete Saw — Collar Puller Ass y . MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 114 Collar Puller Assy .
MQ SP-3035 Concrete Saw — Seal Sleeve Puller Seal/Seal Installation Tool MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 115 Seal Sleeve Puller/Seal Installat.
MQ SP-3035 Concrete Saw — Seal Sleeve Puller Seal/Seal Installation Tool MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 116 Seal Sleeve Puller/Seal Installation Tool NO PART NO PART NAME QTY. REMARK 1# 35163 SCREW, HHC 3/8 – 16 X 4 FULL THREAD 1 2 M18505 SEAL SLEEVE & THRUST WASHER PULLER ASM .
MQ SP-3035 Concrete Saw — Bushin g Extension Kits MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 117 Bushing Extension Kits.
MQ SP-3035 Concrete Saw — Bushin g Extension Kits MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 118 Bushing Extension Kits BUSHING EXTENSION KIT 18501 (.
MQ SP-3035 Concrete Saw — Electric Schematic MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 119 E LECTRIC S CHEMATIC.
MQ SP-3035 Concrete Saw — S p ecifications MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV. #3 (09/29/06) — PAG E 120 S PECIFICATIONS Engine Wisconsin 35 hp V-4, elec tronic ignitio.
OPERATION AND PARTS MANUAL UNITED STATES Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave. Tel. (800) 421-1244 800-427-1244 Fax: 800-672-7877 Carson, CA 90746 Fax (800) 537-3927 310-537-3700 Fax: 310-637-3284 Contact: mq@multiquip.com Mayco Parts Warranty Departme nt 800-306-2926 Fax: 800-672-7877 800-421- 1244, Ext.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Multiquip SP303530 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Multiquip SP303530 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Multiquip SP303530 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Multiquip SP303530 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Multiquip SP303530, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Multiquip SP303530.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Multiquip SP303530. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Multiquip SP303530 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
