Manuale d’uso / di manutenzione del prodotto HG02 del fabbricante Miele
Vai alla pagina of 40
Installation instr uctions Dishw asher T o prevent accidents and machine damage, read these instructions before installation or use. UV 05 690 921 M.-Nr .
IMPORT ANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTRUCTIONS IMPOR T ANTES SUR LA SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . 5 Caring for the en vironment . . . . . . . . . . . . . . . . . .
Installation Installation, maintenance and re - pair work should be by a Miele authorized service technician. Work by unqualified persons could be a hazard and may void the warranty . This equipment is not designed for maritime use or for use in mobile installations such as caravans or air - craft.
Electrical safety Before installation, make sur e the voltage and frequency listed on the data plate correspond with the house - hold electrical supply . This data must correspond to pr event injur y and machine damage. Consult a qualified electrician if in doubt.
Installation L ’installation et les travaux de répa - ration et d’entretien doivent êtr e ef - fectués par un technicien de service autorisé Miele. Les travaux effectués par des personnes non qualifiées, pourraient être danger eux et faire annu - ler la garantie.
Sécurité électrique Avant l’installation, s’assur er que la tension et la fréquence énumérées sur la plaque signalétique correspon - dent à la source d’électricité de la rési - dence. Ces données doivent corres - pondre afin d’éviter de vous blesser et d’endommager l’appareil.
Disposal of the packing material The cardboar d box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please r ecycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of childr en.
G 600 Series Dishwashers Full size models G 636 - G 698 Removing the leg e xtensions The black leg extensions can be removed to r educe the height of the machine to 32 1 / 4 " - 33" (819 - 838 mm) (see Inset). A = Black leg extension (removable) B = White leg (must be installed on machine).
G 800 Series Dishwashers Full size models G 836 - G 898 Slimline models G 801 - G 832 Machine heights of 35" - 37" (889 - 940 mm) can be obtained if the supplied legs are r emoved and extended legs are attached. Contact the Miele T echnical Service Department for the appropriate legs (part # 02 702 601).
Prefinished models Machine heights between 35" and 37" (889 - 940 mm) can be obtained if the supplied legs are r emoved and extended legs are attached. Please contact the Miele T echnical Service Department for the appropriate legs (part # 02 702 601).
1. Install the steam deflector A stainless steel steam deflector is sup - plied to protect the countertops from steam and condesation when the dish - washer is opened. If the countertop is made of Corian®, granite, marble or other solid, waterproof material, the steam deflector is not requir ed.
2. Install the mounting brackets T o ensure stability , this dishwasher should be securely attached to the countertop with the two mounting brackets included.
4. Install the dishwasher under the countertop The dishwasher must be installed so that the water and electricity supplies can be accessed through an adjacent cabinet.
5. Level the legs ^ The rear leveling legs can be ad- justed with a T20 T orx screwdriver by turning the screws at the front of the slide skis. T o raise the machine turn clockwise. T o lower the machine turn counter clockwise. Several turns may be needed to set the correct height.
6. Install the control panel Dishwashers with a selector knob ^ Press the "On/Of f" button in and place the cover , a , over the push button. ^ Insert the dr ying vent grill (if applica- ble), b , into its opening. ^ Position the control panel, c , and fasten it from the inside of the door , d , using the six screws pr ovided.
Dishwashers with insertable push b uttons ^ Press the "On/Of f" button in and place the cover , a , over the push button. ^ Insert the dr ying vent grill, b , into its opening. ^ Position the control panel, c , and fasten it from the inside of the door , d , using the six screws pr ovided.
Dishwashers with fix ed push buttons ^ Press the "On/Of f" button in and place the cover , a , over the push button. ^ Push the drying vent grill, b , into its opening. ^ Position the control panel, c , and fasten it from the inside of the door , d , using the six screws pr ovided.
7. Align the control panel The control panel should be aligned with the drawer fronts of the adjoining kitchen cabinets by adjusting the filler strips. ^ Using an 8 mm socket, turn the nut clockwise or counterclockwise until the filler strips line up with the drawer line.
8. Install the custom door panel A custom door panel matching the kitchen cabinetry can be installed using the provided templates and bracket. X = Panel length A = Height to the underside of the count.
Maximum panel weight A custom door panel must not exceed the listed maximum weight. An over - weight panel will distort the door springs causing the dishwasher door to fall when opened. G 600 door panel G 800 door panel Plastic control panel 13 lbs (5.
^ Place a template on each end of the mounting bracket as shown, making sure the rule marks face the outside of the bracket. ^ Hang the mounting bracket on the machine door . ^ Slide the top edge of the templates under the filler strips and control panel.
^ T ape the bracket to the door panel to hold it in place while the mounting holes are drilled. ^ Drill pilot holes for the screws using a 3 / 32 " (2.5 mm) bit. ^ Attach the bracket to the panel using the 6 screws pr ovided. ^ Remove the templates.
^ Attach the panel to the dishwasher by aligning the bracket tabs with the slots on the door . ^ Open the dishwasher door slightly . If the locking screws on the edge of the dishwasher door can not be reached, the dishwasher will have to be pulled out of its opening a few inches.
If the adjacent cabinetry (or appli - ance) does not have drawer s and alignment to a drawer line is not possible: ^ Hang the bracket on the machine door , without the templates. Tighten the four locking screws on the edges of the door panel. ^ Close the door .
^ Attach the panel to the dishwasher by lining up the bracket tabs with the slots on the door . ^ Open the dishwasher door slightly . If the locking screws on the edge of the dishwasher door can not be reached, the dishwasher will have to be pulled out of its opening a few inches.
9. Secure the dishwasher ^ Open the dishwasher door . If the steam deflector is installed, the mounting bracket holes must align with the slots in the steam deflector . ^ Using flat head screws, secur e the dishwasher to the countertop by screwing thr ough both the mounting bracket and the steam deflector .
For openings exactly 17 3 / 4 " (45 cm) or 23 5 / 8 " (60 cm) wide: ^ Open the dishwasher door and re- move the caps covering the mount- ing holes on the outer edge of the wash cabinet. ^ Fasten the dishwasher to the adja- cent cabinets using the supplied screws and bushings.
10. Adjust the door springs ^ Open the dishwasher door halfway . If the door remains in this position when released, the springs ar e adjusted cor - rectly . If the door drops, the tension on the springs needs to be increased. If it closes on its own, the tension on the springs need to be decreased.
11. Make the plumbing connections An air gap is built into the water inlet system to prevent potable water fr om mixing with waste water . The dishwasher can heat its own water to the temperatures r equired by the wash program. This allows the option of connecting the machine to either a hot or cold water source.
Existing plumbing: If the standard 3 / 8 " copper plumbing for a dishwasher already exists with a com - pression fitting and valve as pictur ed: ^ Cut the 3 / 8 " copper tubing after the valve. ^ Install the 3 / 8 " compression to 3 / 4 " MHT (Male Hose Thread) adapter (supplied with the machine), as illus- trated.
Drainage system specifications: The machine comes equipped with: – A 5 ft. long (1.5 m) flexible drain hose with an internal diameter of 7 / 8 " (22 mm). Drain hose extensions can be order ed from Miele’ s T echnical Service Department. – A built-in swivel connector allowing the drain hose to be routed in any direction.
V enting the drainage system If the dishwasher drain hose is con - nected to a floor drain or to a drain pipe that is less than 8" (20 cm) above the floor , the drain must be vented. Otherwise the water inside the dishwasher may siphon out during the wash program.
12. Make the electrical connection GROUNDING INSTR UCTIONS THIS APPLIANCE MUST BE GROUNDED. In the event of a malfunction or break - down, grounding will r educe the risk of electric shock by providing a path of least resistance for the electrical cur - rent.
P ower outlet The power outlet for the appliance must be installed within a cabinet, on a wall adjacent to the undercounter space in which the dishwasher is located. An o - pening through the partition between the compartments of 1 1 / 2 " (3 to 4 cm) can be made to allow the plug to pass through.
13. T est the unit Once the dishwasher is level and se - cured it should be tested. ^ Remove all packing and literature from inside the unit. The yellow Child Safety Lock key hung on the upper basket must be removed befor e operating the dish - washer .
14. Install the toekick For installations using a continuous toekick or a cabinet matc hing toekick Before installing the toekick , measur e - ments must be taken to ensure that the toekick will not interfere with the com - plete opening of the dishwasher door .
For installations using the included plastic toekick G 600 Series dishwasher ^ Insert the mounting bracket with the flange pointing toward the center of the machine. ^ Push the mounting brackets in as far as possible by releasing the tension on the spring clip (see illustration).
The included toekick will fit without modification if the machine is set to its maximum height and the toekick is re - cessed as far as possible (4" / 10 cm). If the machine height is less than maxi - mum, or if the toekick is not recessed 4" (10 cm), the toekick must be shortened.
^ Carefully open the dishwasher door until it hits the toekick. ^ Using the front lower edge of the door panel as a guide, draw a line across the toekick.
M.-Nr . 05 690 921 / V Alteration rights reserved (NovoplusB,P ,S) / 2702 This bio-friendly paper was bleached without the use of chlorine. 00.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Miele HG02 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Miele HG02 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Miele HG02 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Miele HG02 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Miele HG02, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Miele HG02.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Miele HG02. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Miele HG02 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
