Manuale d’uso / di manutenzione del prodotto G 5105 del fabbricante Miele
Vai alla pagina of 64
Operating Instructions Dishwasher G 5100 G 5105 To prevent accidents and appliance damage read these instructions before installation or use. M.-Nr. 09 016 310 en - US, CA.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel .........................
Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Standby .........................................................3 6 At the end of a program ...............................
WARNING – When using your dishwasher, follow basic precautions, including the following: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. Use the dishwasher only for its intended purpose. This appliance is intended for residential use only.
Installation ~ The dishwasher must be installed and connected in accordance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty.
Use ~ To reduce the risk of injury, do not allow children to play in, on or near the dishwasher. It is possible for small fingers may be pinched in the door. ~ Only use the dishwasher if all panels are properly in place. ~ Do not tamper with the controls.
a Upper spray arm (not visible) b Cutlery tray c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Triple filter system h Data plate i Child Safety Lock i.
Control panel a Program selection b Delay start display c Program sequence display d Check/Refill indicators e Start/Stop button with indicator light f Delay Start button g Turbo button with indicator.
Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption you may connect the dishwasher to a cold water source. ^ For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source.
To open the door ^ Reach under the handle and pull the door open. If the door is opened during operation the dishwasher will stop running. Once the door is closed the program will restart. To close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into place.
Water softener To achieve good cleaning results, the dishwasher needs soft water (water that is low in minerals). Hard water results in calcium deposits on dishware and in the dishwasher. If your tap water hardness is above 4 °d (4 gr/gal) the water should be softened.
Programming the water softener To exit the programming mode at any time turn the dishwasher off with the K button. ^ Press the K button to turn the dishwasher off. ^ Press and hold the "Start / Stop" button and turn the dishwasher on simultaneously using the K button.
Checking the programmed water hardness ^ Press the K button to turn the dishwasher off. ^ Press and hold the "Start/Stop" button and turn the dishwasher on simultaneously using the K button. Keep the "Start/Stop" button pressed for at least four seconds until the "Start/Stop" indicator light comes on.
Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. Filling the salt container , Inadvertently filling the salt container with dishwashing detergent (including liquid detergent) will damage the water softener.
Refill salt message ^ When the "Salt" indicator light comes on, refill the salt after the program has finished. After the container has been filled, the "Salt" indicator light can remain on for a short time. It will go out once the reactivation process is complete.
Deactivate indicators If you only ever use "Tab" detergent products in your dishwasher, you can switch both messages off if you wish. ^ Turn the dishwasher off with the K button. ^ Press and hold the "Start/Stop" button and turn the dishwasher on simultaneously using the K button.
Rinse aid Rinse aid is needed to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. , Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir.
Rinse aid indicator When the Rinse aid indicator first comes on, there will be enough rinse aid left fo r2-3 washes. ^ The rinse aid indicator on the control panel will light when the rinse aid reservoir needs refilling.
Adjusting the dosage In order to obtain an optimal cleaning result you can adjust the dosing quantity of the rinse aid. The dosage selector is preset to 3.
, Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher. Wax, grease and paint will cause permanent discoloration and damage to the dishwasher.
Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boards – Glued items such as old knives with handles glued together around the shank of the blade – Handmad.
Typical load for 10 place settings Upper basket Lower basket Cutlery tray Loading the dishwasher 22.
Typical load for 16 place settings Upper basket Lower basket Cutlery tray Loading the dishwasher 23.
Upper basket , Always use the dishwasher with the upper and lower basket in place. ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans. Long items such as soup ladles, mixing spoons and long knives should be placed lying down across the front of the upper basket.
Adjusting the upper basket In order to gain more space for taller items the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low. Make sure, however, that the basket can slide smoothly in and out of the cabinet.
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Glasses, cups, small plates and saucers can also be arranged in the lower basket. Dishwasher with cutlery tray Dishwasher with cutlery basket Heavily soiled items ^ Place large platters and dishes in the center of the lower basket.
Removable MultiComfort insert The rear section of the lower basket is used for cups, glasses, plates, pots and pans. You can remove the MultiComfort insert to provide more space for larger items such as pots and pans. To remove the insert a ^ Press the yellow handle forwards and remove the insert.
Foldable spikes (depending on model) The spikes at the front are used for plates, soup bowls, platters, desert bowls, and saucers. Both rows of spikes can be folded down to create more room for larger dishware, e. g. pots, pans and bowls. ^ Press the yellow lever down a and fold down the spikes b .
Cutlery tray (depending on model) ^ Arrange the cutlery as shown in the cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge down and forks with the prongs between the holders.
Cutlery basket (depending on model) The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ To avoid risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier.
Optional dishwasher accessories are available from your Miele dealer, Miele or Mieleusa.com (depending on your model some may already be supplied with your machine as standard). If you would like to... the following accessory will need to be ordered..
Detergent , Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Keep detergent out of the reach of children. Keep children away from the dishwasher when the door is open.
Adding detergent ^ Press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to the compartments and close the container flap. ^ Use one tab or add powder or gel detergent to compartment II and close the flap.
Turning on ^ Make sure the spray arms can rotate freely. ^ Close the door. ^ Open the water supply, if it is closed. ^ Press the K button to turn the dishwasher on. The "Start/Stop" indicator light flashes and the indicator of the last set program lights up.
Program guide When to use Program sequence Pre-rinse Main wash Interim rinse Final rinse Drying 12 1 2 Pots & Pans For normally soiled pots & pans with dried on food , and heavily soiled dishware, use 120% detergent recommended.
Standby A few minutes after the last key is pressed or at the end of the program the dishwasher switch into Standby mode to save energy. The indicators and time display (where appropriate) can be turned off and only the Start/Stop indicator light flashes slowly.
Unloading the dishwasher Dishes tend to break and chip more easily when they are hot. Allow the dishes to cool until they are comfortable enough to handle before unloading them. If you open the door fully after switching off, the dishes will cool much faster.
Turbo The "Turbo" function can be used to reduce the program run-times, in programs in which the option is available. In order to achieve optimum cleaning results, consumption rates are increased when Turbo has been selected. ^ Press the K button to turn the dishwasher on.
^ Press the K button to turn the dishwasher on. The "Start/Stop" indicator light flashes. ^ Select the desired program with the "Program" button. ^ Press the "Delay start" button. The last delay start time will show in the time display.
Optimize Standby A few minutes after a button has been pressed or the end of a program, the dishwasher changes to Standby mode to save energy. The indicator lights and time display will go out, and only the Start/Stop indicator will flash slowly. The dishwasher will not switch to Standby mode while a program is running.
Factory default All settings can be reset to factory default. ^ Press the K button to turn the dishwasher off. ^ Press and hold the "Start / Stop" button and turn the dishwasher on simultaneously using the K button. Keep the Start/Stop button pressed for at least four seconds until the "Start / Stop" indicator light comes on.
, Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem Possible fault Solution The Start / Stop indicator does not flash after the dishwasher is turned on with " s ".
Problems water Intake / Drain Problem Possible fault Solution The "Intake / Drain" indicator flashes. The water supply is closed. Open the water supply all the way. The dishwasher stops running. The "Intake / Drain" indicator flashes.
General problems with the dishwasher Problem Possible fault Solution The indicators and the display is dark. Only the "Start/Stop" indicator flashes slowly. The dishwasher has gone into "Standby" mode to save energy. Press the K button to exit Standby mode.
Sounds Problem Possible fault Solution There is a knocking noise in the wash cabinet The spray arm is hitting an item in the basket. Interrupt the program, rearrange items blocking the spray arms. There is a rattling noise in the wash cabinet Items are not secure in the wash cabinet.
Poor cleaning results Problem Possible fault Solution The dishes are not clean. The dishes were not loaded correctly. See "Loading the dishwasher". The program was not powerful enough. Select a more intensive program (see "Program Guide").
Problem Possible fault Solution Dishes are not dry, glasses and cutlery are spotted. The rinse aid setting may be too low, or the rinse aid reservoir is empty. Increase the dosage, refill the reservoir or switch the rinse aid product when refilling (see "Rinse aid").
Problem Possible fault Solution Glasses have a brown or blue discoloration; film cannot be wiped off. Detergent deposits. Change detergent right away. Glasses are dull and discolored; film cannot be wiped off. Glasses are not dishwasher safe. The surface is affected.
Repairs In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door.
To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back.
User Maintenance Instructions To prevent accidents and appliance damage, read these instructions before installation or use..
Check and clean your dishwasher regularly. This will help avoid problems and faults. , Abrasive cleaning agents, all-purpose cleaners, thinner or ammonia based cleaners should not be used on the dishwasher. They will damage the surface. Wash cabinet Generally, the wash cabinet is self cleaning if the correct amount of detergent is used.
Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones). During normal use, the filter system is self-cleaning.
To clean the inside of the filter, the flap must be opened. ^ Push the clips together a and open the flap b . ^ Rinse under running water. ^ Close the flap so that the clip engages. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Lock the filter by turning the handle clockwise.
Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present).
Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system").
Installation Instructions Please refer to the Installation Diagram supplied with these instructions. To comply with IEC sound testing protocols, please contact Miele for additional instructions. Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.
Disposal of the packing material The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children.
, Installation, repairs and other work by unqualified persons could be dangerous. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains.
Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. , CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker.
Connection to the water supply , Installation, repairs and other work by unqualified persons could be dangerous. , Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot (max.
Drainage – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. – The dishwasher is equipped with a 5 ft (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm).
63.
Alteration rights reserved / 1511 G5100/G5105 / INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Miele G 5105 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Miele G 5105 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Miele G 5105 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Miele G 5105 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Miele G 5105, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Miele G 5105.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Miele G 5105. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Miele G 5105 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
