Manuale d’uso / di manutenzione del prodotto G 2874 SCVi del fabbricante Miele
Vai alla pagina of 88
Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time.
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Appliance overview .................................................5 Control panel ....................................................
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Detergent ........................................................3 3 Adding detergent .........................................
Comparison tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Optional accessories .
Appliance overview a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Filter combinat.
Control panel a Selector buttons For selecting the option displayed next to them. For altering the values displayed (+/-). For moving to other menus. b Display See next page for more information. c Clear sensor U For navigating back to the previous menu or deleting values which have been set previously.
Display The display is used to select the following: – the programme – extras – the delay start time – the Settings menu ! – information During a programme, the display shows the following: .
This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time.
Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Under no circumstances should you use a damaged appliance. A damaged appliance could be dangerous. ~ The dishwasher must only be plugged into the electricity supply via a suitable switched socket.
~ This equipment may only be installed in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer. ~ The plastic housing of the water connection contains an electrical component.
Installation ~ The dishwasher must be installed and connected in compliance with the installation instructions. ~ The dishwasher must be correctly aligned to ensure problem-free operation. ~ In order to ensure stability, built-under and integrated dishwashers must only be installed under a continuous worktop which is secured to adjacent cabinetry.
~ Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener. Make sure you have bought the correct packet of dishwasher salt before filling the.
Disposal of the packing material The packing material protects the dryer from transport damages. The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled.
Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ For most economical dishwashing, make full use of the baskets without overloading the dishwasher.
To open the door At the end of the programme, the door will open automatically a little in order to help the drying process. This function can be deactivated (see Settings menu, Drying plus). ^ Pull the handle. If the door is opened during operation all functions are automatically interrupted.
Welcome screen ^ Switch the dishwasher on with the On button U . If the dishwasher is being switched on for the first time, the welcome screen will appear. Setting the language The display will then change automatically to the screen for setting the language.
Setting the time of day The display will then change to the screen for setting the time. } + 12 :0 0 } - Please set the time OK } ^ Set the hours with +/- and confrim with OK . Then set and confirm the minutes. These settings will be saved in memory after the dishwasher has been through one complete programme.
Before using the appliance for the first time, you require: – Approx. 1 kg dishwasher salt, – Domestic dishwasher detergent, – Rinse aid formulated for domestic dishwashers. Every dishwasher is tested at the factory. There will be residual water in the appliance from this test.
You can check the water hardness level measured by the water softener sensor in the display (see Settings menu ! , Water hardness). If the water hardness in your area is constantly lower than 4 °d (= 0.7 mmol/l) you do not need to add salt. The salt refill indicator will be deactivated automatically.
Do not fill the reservoir with water. ^ Add salt only until the reservoir is full or until water runs out of the opening. The salt reservoir holds approx. 1 kg of salt. Do not add any more than 1 kg of salt. As the salt reservoir is filled, displaced water may overflow.
Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically.
^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid reservoir during a programme. ^ Wipe up any spilled rinse aid.
Note Remove coarse food residues from crockery. There is no need to rinse items under running water. , Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher.
Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher.
Upper basket , For safety reasons, do not operate the dishwasher without the upper and lower baskets in place (except when using the Tall items 65 °C program). ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc.
Hinged cup rack ^ To make room for tall items, raise the rack upwards. G 2XXX models: You can set the cup rack at two different heights. ^ Pull the cup rack upwards and click it back into position at the required height.
Support rail This support is designed to hold tall glasses and glasses with stems securely. ^ Lower the support and lean tall glasses against it. ^ You can also remove a section of the cutlery tray to make more room for tall glasses.
Adjusting the upper basket In order to gain more space for taller pieces of crockery in the bottom or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low.
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place thin, delicate glassware in the lower basket. Vario inserts The vario inserts are used for washing cups, glasses, plates, saucers, pots and pans.
Narrow vario insert You can remove the narrow vario insert to make more room for larger items of crockery, e.g. a large, flat pot, or another type of insert: To remove it: ^ Press the insert downwards a and press the catch inwards at the same time b .
Cutlery Cutlery tray (depending on model) ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Cutlery basket (depending on model) ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. ^ Place small spoons in the individual slots to either side of the cutlery basket.
Detergent , Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Miele branded dishwasher cleaning products are available from the Miele Spare Parts Department or via the internet at www.
Dispensing ^ Follow the dosage recommended by the manufacturer on the packaging. ^ Unless directed otherwise, use one detergent tab or add 20 to 30 ml in compartment II, depending on the level of soiling. With very heavy soiling you can also add a small amount of detergent to compartment l (see "Programme chart").
Adding detergent ^ Press the opening catch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a programme. ^ Add the required amount of detergent and close the flap. ^ Make sure that the detergent packaging is properly closed after use to avoid it getting damp and becoming lumpy.
Switching on ^ Open the tap, if it is closed. ^ Open the door. ^ Make sure the spray arms are not obstructed. ^ Switch the dishwasher on using the U button.
You can now specify the type of dishwasher detergent you use. You can choose normal detergent, 2 in 1 tabs or Combi tabs (see Settings menu ! , Detergent type). Selecting Extra options You can now select Extra options for your chosen programme. ^ To do this, first select the Extras option in the menu.
Start the programme ^ Select the Start option. The message Please close the door will appear. If you want to select a different programme or make other changes, select Back and cancel the programme with the Cancel function. ^ Close the door. The In-operation indicator lights up.
Programme finished At the end of a programme the in operation indicator light flashes on and off slowly. It is visible even with the door closed. It will stop flashing one hour after the programme has finished.
Changing a programme If the detergent dispenser flap has already opened, do not change the programme. If a programme has already started and you wish to change it, proceed as follows: ^ Open the door. Sensor wash 1:32h 12:00 Main wash Cancel } ^ Select Cancel and confirm with OK .
Delay start The start time of a programme can be delayed, e.g. to benefit from economy rates of electricity. A delay start time of between 15 minutes and 24 hours can be selected. The delay start time is set in 15 minute steps. , When using the Delay start function, make sure that the detergent compartment is dry before adding detergent.
^ Confirm the start time with OK . The display will change to show the programme menu. ^ Select Start . ^ Close the door. When the set time is reached, the programme selected will begin automatically.
Check the condition of your dishwasher regularly (approx. every 4 - 6 months). This way faults and problems can be avoided. , The outer surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the outer surfaces.
Cleaning the control panel and door front , Remove any soiling immediately. If not, it might become impossible to remove and could cause the outer surface to alter or discolour.
Checking the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. , This dishwasher must not be used without all the filters in place.
To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b . ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet.
Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one).
With the aid of the following guide, minor problems can be easily corrected without calling in a Miele service technician, saving you both time and money. , Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations.
Problem Possible cause Remedy The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following messages appears in the display: Technical fault! Switch the appliance off, turn off the water supply and call the Service Department.
The dishwasher does not fill/drain Problem Possible cause Remedy The In-operation indicator is flashing quickly. The buzzer is sounding. One of the following messages appears in the display: Water inlet fault The tap is closed.
Problem Possible cause Remedy The In-operation indicator is flashing quickly. In the "Without heater" programme the following message appears: Water intake temp. too low The intake water has not reached the required temperature of 45°C (see "Connection to the water supply").
General problems Problem Possible cause Remedy The display is dark. The display has switched off automatically to save energy (Standby mode). Press any button. Stand-by comes to an end. The buzzer sounds during a programme. The following fault message appears in the display: Close the salt reservoir The salt reservoir has not been closed properly.
Problem Possible cause Remedy Detergent residue is left in the dispenser at the end of a programme. The dispenser was still damp when detergent was added. Make sure the dispenser is dry before adding detergent. The detergent dispenser lid cannot be closed properly.
Noises Problem Possible cause Remedy Knocking noise in the wash cabinet. A spray arm is knocking against an item in a basket. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet.
Unsatisfactory washing result Problem Possible cause Remedy The dishes are not clean. The dishes were not loaded correctly. See notes in "Loading the dishwasher" The programme was not powerful enough. Select a more intensive programme. See Programme chart.
Problem Possible cause Remedy Dishes, cutlery and glasses are not dry or are flecked. The amount of rinse aid may be insufficient, or the rinse aid reservoir empty. Replenish the reservoir, increase the dosage or change the brand of rinse aid. See "Before using for the first time".
Problem Possible cause Remedy Glassware has a brown or blue tinge, and film cannot be wiped off. This may be caused by the detergent. Change your detergent. Glassware is dull and discoloured; film cannot be wiped off. The glassware is not dishwasher-proof.
Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet. , The plastic housing of the water connection contains an electrical component.
Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug.
Repairs In the event of any faults that you cannot remedy yourself, please contact: – Your Miele Chartered Agent, or – the Miele Customer Contact Centre You find the telephone number of the Miele Customer Contact Centre on the back cover of the manual.
Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005; AS/NZS 6400:2005 Standard programme for energy label comparison tests: Normal Capacity: 12/14 place settings (depending on model) Amount of deter.
Model types G 1xxx with a cutlery tray (12 place settings): Upper basket Cutlery tray Lower basket Comparison tests 62.
Model types G 2xxx with a cutlery tray (14 place settings): Upper basket Cutlery tray Lower basket Comparison tests 63.
Crockery type Soiling Programme mixed, non-sensitive crockery normal soiling variable, sensor controlled wash shortened cycle glasses and plastic containers, sensitive to high temperatures light soili.
Programme Detergent Compartment I 2) Compartment II 2) Sensor wash – 25 ml or 1 Tab + Turbo Quick wash 40°C – 20 ml or 1 Tab 3) Sensor wash gentle # – 20 ml or 1 Tab Light soiling 50 °C – 25.
Programme Programme sequence Pre-wash Main wash °C Interim rinse Final rinse °C Drying 12 Sensor wash Variable programme sequence, sensor controlled adjustment to amount of crockery and soiling if r.
Consumption 1) Duration 1) Energy Water Cold water 20 °C kWh Hot water 60 °C kWh Litres Cold water 20 °C h:min Hot water 60 °C h:min 0,95-1,35 0,70-1,00 8-17 1:30-2:38 1:18-2:21 0,55 0,20 10 0:38 .
Programme When to use Hygiene Programme with special parameters for hygienic removal of bacteria from baby bottles, chopping boards, utensils etc. Pre-wash For rinsing crockery to avoid smells, if a complete cycle is not yet needed.
Programme sequence Consumption 1) Duration 1) Energy Water Pre- wash Main wash °C Interim rinse 12 Final rinse °C Drying Cold water 20 °C kWh Hot water 60 °C kWh Litres Cold water 20 °C h:min Hot.
To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele Chartered Agent or from the Spare Parts Department (some may be supplied as standard, depending on model). If you would like to … you will need to order … … wash long-stemmed glassware … a glassware insert for the upper basket .
, Please follow the installation instructions carefully. All electrical work should be carried out only by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the appliance while installation work is being carried out.
The Miele waterproof anti-leak system Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply , Water in the dishwasher must not be used as drinking water.
! The inlet hose must not be shortened or damaged in any way as it contains electrical components (see illustration). This appliance incorporates back- flow protection complying with AS/NZS 3500.1.2. No further backflow protection required for connection to the water supply.
Drainage – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm.
Dishwasher model G 1XXX G 2XXX Height 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm 59.8 cm Width of building-in recess 60 cm 60 cm Depth 57 cm 57 cm Weight Max.
Settings menu ! for changing standard settings To open the Settings ! menu ^ Switch the dishwasher on with the On button U ,i fi ti s switched off. The programme selection menu will appear in the display. If the memory function is activated, the menu for the programme last selected will be displayed instead (see "Memory").
Language J The display can be set to appear in one of several different languages. You can change the language for the display via the "Language ! " sub-menu.
Detergent type To ensure excellent results you can programme your dishwasher for the type of detergent you are using. You can choose normal detergent, 2 in 1 tabs or Combi tabs. The programme sequence and duration will be adjusted for the type of detergent selected.
Drying plus At the end of a programme with a drying phase (see "Programme chart"), the door will open automatically a little in order to help the drying process. This function can be deactivated if wished. ^ Select the option you want and confirm with OK .
External water softening system If your dishwasher is connected to an external water softening system which uses salt to reactivate, to achieve good cleaning results you will still need to set the wat.
Change main menu You can change the order of the programmes in the main menu and also enter your favourite programmes into the first two programme places.
Save extras You can set additional functions, e.g. Pre-wash, for individual programmes (see "Operation, Selecting Extra options"). You can use the Save extras option to save settings you have chosen for a particular programme so that they are automatically selected when you run the programme in the future.
Buzzer When the buzzer is activated, an audible tone sounds at the end of a programme and when there is a fault. The buzzer is activated as standard at the factory. Buzzer at the end of a programme You will hear the buzzer at the end of a programme in bursts of five with a short pause in between.
Keypad tones An audible tone sounds each time a button is pressed. There are seventeen different volume settings. The factory default setting is 8. ^ Select the volume you want and confirm this with OK . Brightness There are seventeen different display brightness settings.
Showroom programme The programme is for display use only. The dishwasher is fitted with various demonstration programmes for showroom use. The Demo mode and Demo mode in continuous loop programmes demonstrate operation and functions. – Demo mode : This programme is started by pressing any button.
86.
87.
Alteration rights reserved/ G2874 / 1409 M.-Nr. 07 600 690 / 00.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Miele G 2874 SCVi è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Miele G 2874 SCVi - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Miele G 2874 SCVi imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Miele G 2874 SCVi ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Miele G 2874 SCVi, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Miele G 2874 SCVi.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Miele G 2874 SCVi. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Miele G 2874 SCVi insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
