Manuale d’uso / di manutenzione del prodotto 8452-5-SS1 del fabbricante Meco
Vai alla pagina of 24
For Customer Service, call 1-800-251-7558 or visit our web site at www .meco.net FOR OUTDOOR HOUSEHOLD USE ONL Y . NOT FOR COMMERCIAL USE. • Failure to follow these instructions could result in fire or explosion which could cause death, serious personal injury , or property damage.
© MECO CORPORA TION ® 2006 — NOTICE — MECO CORPORA TION STRIVES T O BE A QUALITY SUPPLIER OF CONSUMER PRODUCTS. IF WE OMITTED ANY P ARTS NEEDED FOR ASSEMBL Y , OR YOU NEED TROUBLESHOOTING INFORMA TION, PLEASE CONT ACT US USING OUR T OLL FREE NUMBER.
3 P ARTS ILLUSTRA TIONS If you need replacement part s, refer to the Parts Illustrations and the Parts List to find the exact p arts you need. If you have any questions which require help, contact Customer Service and be sure to mention the model number of your grill.
(53) DRIP TRA Y (51) FOIL P AN (54) FLAME DIFFUSER (63) MANIFOLD ASSEMBL Y (LP) (60) HEA T INDICA TOR PA RTS LIST ITEM DESCRIPTION PA RT # QTY. 1 Owner's Manual 03.6538.00 1 2 Back Panel-Silver 03.6508.00 1 3 Back Panel-Black 03.6508.01 1 4 LP Cylinder Clamp 03.
PA RTS LIST (Cont'd) 31 Bowl Assembly SS/Black 03.6523.00 1 32 Hood Assembly 430 SS/Silver 03.6524.00 1 33 Hood Assembly 430 SS/Black 03.6524.01 1 34 Spring Pin, Hood Hing e 03.6525.00 2 35 Clevis Pin, Hood Hinge 03.6526.00 2 36 Side Table, Lef t Burner SS/ Silver 03.
6 FIG . 2 STEP 3) Front Crossbar Assembly: T urn cart assembly right side up. Att ach Front Crossbar (21/22) to side p anels with two M6 x 15 screws into the threaded insert s in the ends of Side Panels. (FIG . 3A) Att ach Bottom Panel Brace (9/10) to Crossbar (21/22) with two Screws and Nut s.
7 STEP 4) CASTER ASSEMBL Y : Lay cart on the floor with Back Panel side down. Assemble Fixed Casters (23) to the LEFT Side of Bottom Panel and Swivel Lock Casters (24) to the RIGHT Side of Bottom Panel. Insert eight M6x15 Bolt s (7) through the caster bracket holes into the threaded holes in the Bottom Panel.
STEP 6) HOOD/BOWL T O CART ASSEMBL Y : Lif t the Hood/Bowl Assembly (30) over the cart assembly and set it down until it rests on the inside top flanges of the cart. (FIG . 6A) Align the holes in the side of the Hood/Bowl with the holes in the cart bracket s.
9 STEP 7) BURNER SIDE T ABLE ASSEMBL Y : Align the four holes of the LEFT Side Burner T able (36/37) bracket with the threaded insert s in the side of the Bowl. Insert four M6x15 Bolt s (7) into the holes and screw them in with a screwdriver , but do not tighten.
10 STEP 9) SIDE BURNER ASSEMBL Y : Insert the Side Burner (44) and the Electrode Wire through the front of the large hole in the Side T able. (FIG . 9A) Install the burner tube end over the valve nozzle. (FIG . 9B) Secure the Burner to the bracket with two M4x8mm Screws (45).
11 STEP 1 1) BURNER REMOV AL/RE-ASSEMBL Y : The Burners (49) are already inst alled in the grill. There is some cardboard p acking underneath each burner; it will burn off the first time of use. If you wish to remove it: 1. Remove the burner pin. (FIG .
12 STEP 13) FLAME DIFFUSER/GRID/ W ARMING RACK ASSEMBL Y : Lay a Flame Diffuser (54) over each Burner on the lower Body ridges from front to back. Place each Flame Diffuser in the individual guides to keep from sliding. (FIG . 13A) Place the Cooking Grids (55) over the Burner Diffusers on the upper Body ridges.
13 T o reduce the risk of serious bodily injury or death: · Use only prop ane gas in this LP gas grill. · Do not attempt to convert an LP unit to natural gas. · Any use or alteration of this unit not intended could be unsafe and will void your warranty .
14 FIG . 15B Hand tighten coupling nut in clockwise direction Disconnecting LP gas cylinder: 1) T urn all control knobs to the “off” position and turn the handle on the LP gas cylinder clockwise until it stops. 2) T urn coupling nut on regulator counterclockwise until regulator is released from the threaded LP cylinder gas nozzle.
How to perform a leak test: Supplies Needed for a Leak T est: Clean paint brush, water , and dish washing liquid. 1) Use an LP Cylinder equipped with an OPD (Overfill Prevention Device) and have it filled at an authorized LP gas dealer by a qualified attendant.
1. Open the Hood. 2. Import ant: Make sure control knobs are turned “Off”. (FIG . 17B) 3. T urn the LP Gas Cylinder valve open counter clockwise until it stop s. (FIG . 17A) 4. Push far lef t control knob in and turn counter clockwise to the High position.
17 FIG . 18A FIG . 18B Check the flame before each cooking session and throughout the grilling season. Also check especially after long periods of storing the grill. If the flame is significantly yellow in color , the appropriate amount of LP gas in the air/LP gas mixture is not correct.
T o reduce the risk of serious bodily injury , death or grill damage: · Do not cover more than half (50%) the cooking area if using griddle plates. Full coverage of cooking area will cause overheating below the plates.
CARE AND MAINTENANCE A) Drip T ray , Grease Pan, Foil Pan- Loosen the two screws on the sides holding the Drip T ray . Remove and scrape away food and fat residue from the drip tray . Empty and wash the Foil Pan and Grease Pan with hot soapy water and a cloth.
20 Open up main burner holes with a small nail or wire. Wire Brush FIG . 20D T o reduce the risk of a fire beneath the grill: · Inspect and clean burner/venturi tubes for insect s and insect nests. · Be sure burners are re-inst alled properly before using grill.
21 Problem Possible Cause Solution Burners will not light using the ignitor Burners not assembled correctly Not holding ignitor switch long enough for pulse spark No spark LP- gas cylinder is empty LP.
22 Problem Flames blow out Flare up Persistent grease fire Unable to fill LP tank Humming or whistling from the regulator Possible Cause High or gusting winds Gas in LP cylinder is low Excess flow valve tripped Grease build up Excessive fat in meat Grease trapped around burner system Some dealers have older fill nozzles with worn threads.
IMPORT ANT NOTICE The Gas Grill is setup to operate with a LP Gas Cylinder equipped with an OPD (Overfill Prevention Device). This is a secondary device to prevent the overfill of your LP Gas cylinder . The proper methods for the filling of your LP Gas cylinder are by weight or volume, as described in NFP A 58.
P/N 03.6538.00 REV . 4/06 24 MECO CORPORA TION LIMITED W ARRANTY This product is warranted to the original consumer purchaser against defects in material and workman- ship under normal outdoor household use and correct assembly (if assembled by the consumer purchas- er).
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Meco 8452-5-SS1 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Meco 8452-5-SS1 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Meco 8452-5-SS1 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Meco 8452-5-SS1 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Meco 8452-5-SS1, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Meco 8452-5-SS1.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Meco 8452-5-SS1. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Meco 8452-5-SS1 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
