Manuale d’uso / di manutenzione del prodotto EH7500W del fabbricante Makita
Vai alla pagina of 16
PETR OL HEDGE TRIMMER EH5000W EH6000W EH7500W INSTRUCTION MANUAL W ARNING: T o reduce the RISK of injury , user must read and understand the instruction manual before using the hedge trimmer . Manufacturer reserves the right to change specications without notice.
2 Thank you very much for selecting the MAKIT A hedge trimmer . W e are pleased to be able to offer you the MAKIT A hedge trimmer which is the result of a long development program and many years of knowledge and experience.
3 General Instructions - THIS MACHINE CAN CAUSE SERIOUS INJURIES. Read the Instructions carefully for correct handling, preparation, maintenance, starting and stopping of the machine.
4 Starting up the hedge trimmer - Please make sure that there are no children or other people within a working range of 15 meters (5), also pay attention to any animal in the working vicinity . - Before operating, always check the hedge trimmer is safe for operation.
5 Method of operation - Always use two hands to grip each handle during operation. - Use the hedge trimmer only in a good light and visibility . During cold seasons beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing.
6 TECHNICAL D A T A Model EH5000W EH6000W EH7500W Dimension (L x W x H) mm 1,014 x 262 x 216 1,1 19 x 262 x 216 1,259 x 262 x 216 Mass (without blade cover) kg 4.8 5.0 5.2 V olume (fuel tank) L 0.4 Engine displacement cm 3 22.2 Cutting length mm 483 588 728 Maximum engine performance kW 0.
7 DESIGNA TION OF P AR TS DESIGNA TION OF P ARTS DESIGNA TION OF P ARTS DESIGNA TION OF P ARTS 1 Blade 7 Carburetor (not shown) 13 Release lever 2 Blunt extension 8 I-O switch (ON-OFF) 14 Mufer 3 F.
8 Fuel and oil mixture - The engine of the hedge trimmer is a high-efciency two-stroke engine. It is run with a mixture of fuel and two-stroke engine oil. The engine is designed for unleaded regular fuel with a min. octane value of 91 ROZ. In case no such fuel is available, you can use fuel with a higher octane value.
9 Refuelling - The engine must be switched off. - Stop the engine during refuelling, keep away from ames and do not smoke. - T ake care not to spill either fuel or oil in order to prevent soil contamination. Clean the hedge trimmer immediately after fuel has been spilled.
10 Move at least 3 meters away from the place of refuelling. Place the hedge trimmer on a clean area of ground. Make sure that the cutting blades do not come into contact with the ground or any other objects. Cold starting: (When the engine is cold or it has been stopped for more than 5 minutes or when fuel is added to the engine.
11 - Never operate the hedge trimmer with a loose grip. - Never touch the cutting blades when starting the engine and during operation. - Operate the hedge trimmer in such a manner as to avoid inhalation of the exhaust gases. Never run the engine in enclosed rooms (Risk of gas poisoning).
12 - T urn off the engine and remove the spark plug connector when cleaning/replacing/sharpening the cutting blades or carrying out any maintenance. - Never straighten or weld a damaged cutting blade. - Frequently inspect the cutting blades for damage with the engine switched off.
13 Checking and adjusting the idling speed The cutting blades should not run when the engine is at idle. - Idle speed should be set to 3,000 min -1 (rpm). - If necessary , adjust the idle screw (the cutting blades must not run when the engine is on idle).
14 For any maintenance or adjustment not described in this manual, ask your local Makita authorized service center . Daily checkup and maintenance T o ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular intervals.
15 - When keeping the machine in storage for a long time, drain fuel from the fuel tank and carburetor , as follows: Drain all fuel from the fuel tank. - Remove the spark plug and add a few drops of oil into the spark plug hole. Then, pull the starter gently to conrm that oil lm covers inside of the engine and tighten the spark plug.
Makita Corporation 885103-9 www .makita.com ALA.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita EH7500W è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita EH7500W - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita EH7500W imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita EH7500W ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita EH7500W, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita EH7500W.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita EH7500W. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita EH7500W insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
