Manuale d’uso / di manutenzione del prodotto C del fabbricante Makita
Vai alla pagina of 19
O WNERS MANU AL FOR O il Free Air Compressor MODEL No $ C SPECIFICA TION CHART Model # AC00 1 Horsep ower 1/6 HP SCFM @ 40 PSIG 0.58 SCFM @ 90 PSIG 0 . 45 Cut-In Pressure 95 PSI Cut-Out Pressure 1 25 PSI Bore 32 mm S troke 11 mm V oltage -Single Phase 120 Motor RPM 3400 Amperage @ max pressure 1.
Page 2 T ABLE OF CONTENTS SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 W arning Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 GLOSSARY . . . . . . . . . . . . . . . . . .
Page 3 IMPORT ANT SAFETY INSTRUCTIONS *SA VE THESE INSTRUCTIONS* WARNING IMPROPER OPERA TION OR MAINTENANCE OF THIS PRODUCT COULD RESUL T IN SERIOUS INJUR Y AND PROPERTY D AMAGE. READ AND UNDERST AND ALL WARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT .
Page 4 HAZARD Risk of Air T ank Bur sting Risk of Attachments and Accessories Bur sting HOW T O PREVENT IT · Drain the tank DAILY or after each use. If tank develops a leak, replace it immediately with a new tank or new compressor unit. · Never drill into, weld, or make any modifications to the tank or its attachments.
Page 5 HAZARD Risk of Electric Shock Risk of Explosion or Fire Risk to Breathing WHA T CAN HAPPEN • Y our air compressor is powered by electricity . Like any other electrically powered device, if it is not used properly , it may cause electrical shock.
Page 6 HAZARD Risk to Breathing (continued) Risk from Compressed Air Risk from Mo ving Par ts Risk of Bur n WHA T CAN HAPPEN solvents, p aint remover , insecticides, weed killers, etc., contain harmful vapors and poisons. • Breathing compressor or sprayed materials vapor can result in serious injury .
Page 7 GLOSSAR Y CFM: Cubic feet per minute. SCFM: S tandard cubic feet per minute; a unit of measure of air delivery . PSIG: Pounds per square inch gauge; a unit of measure of pressure. CUT -IN PRESSURE: While the motor is off, air t ank pressure drops as you continue to use your accessory or air tool.
Page 8 product was shipped directly to you, report any damages to the carrier and arrange for inspection of goods immediately . ST ORAGE Before you store the air compressor , make sure you do the following: 1. Review the “ Maintenance” and “Operating Procedures” sections and perform maintenance as necessary .
Page 9 reaches “cut-out” pressure. PRESSURE SWITCH: The pressure switch automatically start s the motor when the air tank pressure drop s to the factory set “cut-in” pressure. It stops the motor when the air tank pressure reaches the factory set “cut-out” pressure.
Page 10 Initial Star t Up Pr ocedure: 1. Open the air receiver's drain valve. 2. Plug power supply cord into correct power source. 3. Run the compressor for a minimum of twenty (20) minutes in the no-load condition to seat the piston ring and check valves.
Page 11 grounding plug. The plug must be used with an outlet that has been installed and grounded in accordance with all local codes and ordinances. The outlet must have the same configuration as the plug. DO NOT USE AN ADAPTER. Inspect the plug and cord before each use.
Page 12 MAINTENANCE W ARNING: UNIT CYCLES AUTOMA TICALL Y WHEN POWER IS ON. WHEN DOING MAINTENANCE, YOU MA Y BE EXPOSED TO VOL T AGE SOURCES, COMPRESSED AIR OR MOVING P ARTS. PERSONAL INJURIES CAN OCCUR. BEFORE PERFORMING ANY MAINTENANCE OR REP AIR, UNPLUG THE COMPRESSOR AND BLEED OFF ALL AIR PRESSURE.
Page 13 Allow oil to drain completely . 2. Replace the oil drain plug (The use of a sealing compound or T eflon tape to avoid leakage is recommended.) 3. Refill with the recommended oil to the proper level. SERVICE INSTRUCTIONS Air Filter - Inspection and Replacement: • Keep the air filter clean at all times.
Page 14 TROUBLESHOO TING GUIDE PERFORMING REP AIRS MA Y EXPOSE VOL T AGE SOURCES, MO VING P ARTS OR COMPRESSED AIR SOURCES. PERSON AL INJURY MA Y OCCUR. PRIOR T O A TTEMPTING ANY REP AIRS, UNPLUG THE COMPRESSOR AND BLEED OFF T ANK AIR PRESSURE. CA USE Defective pressure switch.
Page 15 PROBLEM Pressure reading on the regulated pressure gauge drops when accessory is used. Air leak from safety valve. Compressor is not supplying enough air to operate accessories. Motor will not run. CA USE It is normal for "some" pressure drop to occur .
Page 16 PROBLEM Motor will not run. (con’t) Regulator knob has continuous air leak. Regulator will not shut off at air outlet. CA USE • Check valve is stuck open. • Loose electrical connections. • Possible defective capacitor . • Paint spray on internal motor part s.
COMPRESSOR MAIntEnAnCE LOG DA tE tyPE Of MAIntEnAnCE OR REP AIRS Page 1 .
complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to an Authorized Makita Service Center . Be sure to attach a letter to the outside of the carton detailing the problem with your tool.
MAKIT A W ARRANTY Makita Corporation 3-1 1-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan Page Servicio y Garantía / Registro d e Produ cto MAKIT A LIMITED ONE YEAR W ARRANTY W arranty Polic y Every Makita tool is thoroughly inspected and tested bef ore leaving the factory .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita C è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita C - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita C imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita C ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita C, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita C.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita C. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita C insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
