Manuale d’uso / di manutenzione del prodotto 5044KB del fabbricante Makita
Vai alla pagina of 20
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Cir cular Sa w with Dust Collection Equipped with Electr.
2 SPECIFICATIONS • Manuf acturer rese rves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions.
3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock.
4 SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual.
5 does not touch the blade or any other part, in all angles and depths of cut. T o chec k lower guard, open lowe r guard by hand, then release and watch guard closure . Also check to see that Retracting Le ver does not touch tool housing. Leaving b lade exposed is VER Y DANGER OUS and can lead to serious personal injur y .
6 saw is restarted. Support large panels to minimize the risk of blade pinching and KICKB ACK. Large panels tend to sag under their own weight. Suppor ts must be placed under the panel on both sides, near the line of cut and near the edge of the panel as s hown in Fig.
7 workpiece pr operly and to hold the saw firmly to pre vent loss of control which could cause personal injury . Fig. 4 illus- trates typical hand support of the saw . 16. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made.
8 SYMBOLS USD201-2 The f ollowings show the symbols used for tool. V ....................... volts A ....................... amperes Hz ..................... her tz ................ alternating current .................... no load speed ..............
9 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Adjusting depth of cut CA UTION: • After adjusting the depth of cut, alwa ys tighten the lev er securely .
10 Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s witch tr igger actuates properly and retur ns to the “ OFF ” position when released. T o prev ent the switch trigger from being accidentally pulled, a lock-off b utton is provided.
11 T o install the blade, f ollow the remov al procedure in rev erse. Install the cup washer , inner flange, saw b lade, outer flange and he x bolt on the spindle in that order. BE SURE T O TIGHTEN THE HEX BOL T CLOCKWISE SECUREL Y . After installing the blade , install the dust box and tighten the clamping screw to secure the dust bo x.
12 Hold the tool firmly . The tool is provided with both a front grip and rear handle. Use both to best gr asp the tool. If both hands are holding saw , they cannot be cut by the blade. Set the base on the workpiece to be cut without the blade making any contact.
13 Use a screwdriv er to remove the brush holder caps. T ake out the worn carbon br ushes , inser t the new ones and secure the brush holder caps. After replacing brushes, plug in the tool and break in brushes by running tool with no load f or about 10 minutes.
Memo 14.
Memo 15.
Memo 16.
17 Fold Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitb y , Ontario L1N 7B7.
18 Y our answer s to the following questions are appreciated. Date Purchased Model No. Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Y ear 20 Unde.
19 F actory Ser vice Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “ tools ” or con- tact our customer service department (Tel) 1-800-263-3734 When you need service.
Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita 5044KB è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita 5044KB - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita 5044KB imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita 5044KB ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita 5044KB, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita 5044KB.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita 5044KB. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita 5044KB insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
