Manuale d’uso / di manutenzione del prodotto 4302C del fabbricante Makita
Vai alla pagina of 16
Electronic Jig Saw 26 mm (1"l MODEL 4302C 219 mm 2 5 ky (8 5/8") (5 5 Ibs) 1,000 3.000 60 mm 10 mm (2 3/8") !3/8"1 INSTRUCTION MANUAL SPEC IF I CAT IONS weight Strokes Overall per .
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- READ ALL INSTRUCTIONS. 1.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
ADDITIONAL SAFETY RULES 1. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- 2. Don't cut hollow pipe. 3. Do not cut oversize workpiece. 4. Check for the proper clearance beneath the workpiece before cutting so that 5. Hold the tool firmly.
Installing Makita jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. Use the hex wrench to loosen the bolt. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go.
Installing universal shank jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6.
Straight line or orbital cutting action Conventional jig saws cut with a straight line action, that is, the blade moves only up and down in a straight line. Your saw also cuts in this manner but, for softer workpieces, an orbital cutting action can be selected.
Speed change To adjust the tool speed, turn the speed change dial while the tool is running under no load. The tool speed can be adjusted between 1,000 and 3,000 strokes per minute. The reference table on the right denotes the relationship between the number set- approximate strokes per minute at that Number 1 2 1 setting.
Operation Turn the tool on and wait until the blade attains full speed. Then rest the base flat on the workpiece and gently move the tool forward along the previously marked cut- ting line. When cutting curves, advance the tool very slowly. I CAUTION : Failure to hold the tool base flush with the workpiece may cause blade breakage.
Front flush cuts Loosen the bolt on the back of the base with the hex wrench, then slide the base backwards. Check the contact between the back edge of the blade and the roller, then secure the bolt. Plunge cutting Starting a cut at other than the edge of the workpiece without first drilling a starting hole requires a "plunge cut".
Using guide rule (Rip fence) When cutting widths of under 150 mm (6") repeatedly, use of the guide rule will assure fast, clean, straight cuts. To attach the guide rule (rip fence), secure the rule holder to the base with the screw (do not tighten).
To attach the circular guide, use the pin, inserting it in the center hole (arrow) and secure it with the threaded knob. Then slide the base of the tool forwards. The circular guide attaches to the base of the tool in the same manner as the guide rule (rip fence).
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. The tool will stop when the carbon brushes wear to a certain length. When this occurs, both carbon brushes should be replaced.
0 Jig saw blade Wood and plywood - Plastics Aluminum Mild steel 1 5 - 3 mm thick 1 - 6 mm thick 1 - 3 mm thlck 11/16" - 118") 13/64" - 114") 13/64" - 118") ti 4 - 60 mm t.
Oct 01 '87 EN ELECTRONIC JIG SAW Model 4302C Note The switch. noise suppressor and other part configurations may differ from country to country 15.
MODEL 4302C ITEM NO NO USED Me 3 4 5 6 7 6 9 10 11 12 13 14 17 1s 19 20 21 22 23 24 25 26 27 26 29 30 31 32 33 34 35 36 37 38 39 40 41 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 I 1 1 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita 4302C è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita 4302C - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita 4302C imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita 4302C ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita 4302C, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita 4302C.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita 4302C. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita 4302C insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
