Manuale d’uso / di manutenzione del prodotto 4301BV del fabbricante Makita
Vai alla pagina of 16
Jig Saw MODEL 4301BV Variable Speed INSTRUCTION MANUAL SPEC IF I CAT IONS Strokes Overall Net per mln Max cutting capacities Wood at 90' 1 Wood at 45' 1 Steel at 90' Length of stroke I length 1 weight Manufacturer reserves the rlght to change specifications wlthout notice.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 5.
Ampere Rating More Not More Than Than 0-6 6 - 10 10 - 12 12 - 16 17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 18. STAY ALERT. Watch what you are doing, use common sense.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user-as well as damage to the tool.
Installing Makita jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. Use the hex wrench to loosen the bolt, With the blade teeth facing forward, insert the blade into the blade holder as far as it will go.
Installing universal shank jig saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6.
Position 0 - For cutting in soft steel, stainless steel and plastics. For clean cuts in wood and plywood. Position I - For cutting in soft steel, aluminum and hard wood. Position I1 - For cutting in wood and plywood. For fast cutting in aluminum and soft steel.
Bevel cutting With the base tilted, vou can make bevel ., cuts at any angle between 0" and 45" (left or right). Loosen the bolt on the back of the base with the hex wrench, and slide the base backwards. Tilt the base to the desired angle. The edge of the housing indicates the bevel angle.
Plunge cutting Starting a cut at other than the edge of the workpiece without first drilling a starting hole requires a "plunge cut". This can be accomplished by tipping the tool forward until the front end of the base rests against the workpiece.
To attach the guide rule (rip fence), use the hex wrench to loosen the bolt on the base in front, slip in the guide rule and secure the bolt. Using circular guide (optional accessory) Use of the circular guide insures clean, smooth cutting of circles (radius; under 200 mm; 7-7/8") and arcs.
Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant biade wear. The underside of the workpiece can be greased instead of using a coolant.
MA1 NTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to about 5 mm (3/16") or less.
OPTIONAL ACCESSORIES NOTE: The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual.
No. 6-24 No. 6- 25 No 6-26 No 6-27 14 /3,6:.mmlt:dc: Ol?,i43 q17&2 mrj;Ahq!c7 Also ideal for cutting H stainless steel 3 ~ 55 mm thick 3 ~ 55 mm thick 3 ~ 30 mm thick 3 10 mm thick for cutt,ng 111.
Aug -26 84 US JIG SAW Model 4301BV Note: The switch and other part configurations may differ from country to country. 15.
MODEL 4301BV ITEM NO. NO. USED MAWME I 2 3 4 5 6 7 6 9 10 11 12 13 14 15 16 17 19 20 21 22 23 24 25 26 27 26 29 30 31 32 33 24 35 36 37 38 39 40 41 42 43 ~ Note The switch I 4 4 1 1 4 2 1 1 2 1 1 1 2 .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita 4301BV è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita 4301BV - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita 4301BV imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita 4301BV ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita 4301BV, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita 4301BV.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita 4301BV. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita 4301BV insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
