Manuale d’uso / di manutenzione del prodotto 4191DZ del fabbricante Makita
Vai alla pagina of 18
Cordless Cutter 85 mm 13-318") 85 mm (3-3/8") MODEL 4191DZ 85 mm (3-3/8") MODEL 419lDWA With Battery Cartridge and Fast Charger 0 ~ 24 mm 0 ~ 18 mm 316 mm 2.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE I. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) 25 AWG Size of Cord 18 50 100 150 18 18 16 4.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents.
ADDITIONAL SAFETY RULES 1. Be aware that this is always in an operating condition, because it does not have to be plugged into an electrical outlet. 2. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately.
Installing or removing the battery cartridge 1222 *Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.
Charging *Your new battery cartridge is not charged. You will need to charge it before use. Use the fast charger Model DC1410 to charge the battery cartridge. *Plug the fast charger into the proper NC voltage source. The charging light will flash in green color.
Installing or removing diamond wheel CAUTIO N : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the wheel. To install the wheel, first loosen the bolt with the hex wrench and remove the bolt and the flange.
installing water supply Attach the tank holder on the tank. The tank Attach the tank holder onto the motor hous- ing. Tighten the screw (B) securely. -Tank Tank holder installing portion -, Connect the cap on the end of the polyvinyl tube to the mouth of the tank.
Hex wrench storage When not in use, the hex wrench can be conveniently stored. Hex wrench 4b Adjusting the depth of cut Loosen the screw on the depth guide and move the base up or down. You can read the depth of cut by aligning the top of the notch in the depth guide with the graduations on its right side.
Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0" engraved on it with your cutting line on the workpiece. For 45" bevel cuts, align the edge with 45" engraved on it with your cutting line.
Operation Hold the tool firmly. Set the base plate on the workpiece to be cut without the wheel making any contact. Then turn the tool on and wait until the wheel attains full speed. Feed water to the wheel by adjusting the water cock to obtain a gentle flow of water.
MAINTENANCE CAUTION: Always be sure that the charger is unplugged and the battery cartridge is removed before attempting to perform inspection or maintenance.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual.
Feb -29-'96 US 85 mm (3-3/8") CORDLESS CUTTER Model 4191D Note: The switch and other part configurations may differ from country to country. 16.
MODEL 4191D Feb.-29-'96 US 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 21 28 29 30 31 32 I:"," $& DESCRIPTION 1 Motor Housing 37 1 1 Cap 38 1 1 Tank 39 1 1 Pan Head.
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd I To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b).
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita 4191DZ è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita 4191DZ - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita 4191DZ imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita 4191DZ ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita 4191DZ, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita 4191DZ.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita 4191DZ. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita 4191DZ insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
