Manuale d’uso / di manutenzione del prodotto 2703X1 del fabbricante Makita
Vai alla pagina of 28
With Electric Brake 210 mm (8-1/4”) MODEL 2702X1 MODEL 2702 255 mm (10”) MODEL 2703X1 MODEL 2703 T able Saw www .makita.com INSTRUCTION MANUAL DOUBLE INSULA TION W ARNING: For your personal safety , READ and UNDERST AND before using. SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
2 MODEL Arbor hole Blade diameter Cutting capacities 90 ° 45 ° T able size (W x L) No load speed (RPM) Dimensions (L x W x H) Maximum dado capacity Net weight 18kg (40 lbs) 4,600/min 560mm x 686mm x.
3 9. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed; for example, don’t use circular saw for cutting tree limbs or logs. 10. WEAR PROPER APP AREL. Wear no loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts.
4 16. REDUCE THE RISK OF UNINTENTIONAL ST ARTING. Make sure switch is in off position before plugging in. 17. USE RECOMMENDED ACCES- SORIES. Consult the owner ’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury to persons.
5 1. Wear eye protection. 2. Don ’ t use the tool in presence of flam- mable liquids or gases. 3. NEVER use the tool with an abrasive cut-off wheel installed. 4. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately .
6 18. Do not perform any operation freehand. Freehand means using your hands to sup- port or guide the workpiece, in lieu of a rip fence or miter gauge. 19. NEVER reach around or over saw blade. NEVER reach for a workpiece until the saw blade has completely stopped.
The tool is shipped from the factory with the saw blade and blade guard not in the installed condition. Assemble as follows: CAUTION: • Always unplug the tool before assembly . Installing saw blade Remove the table insert on the table. Hold the outer flange with the offset wrench and loosen the hex nut counterclockwise with the wrench.
8 Installing blade guar d CAUTION: • Before installing the blade guard, adjust the depth of cut to its maximum elevation. Insert the spreader between the blade guard mounting portion (stay) and the pressure plate. T ighten the hex bolts (A) with the offset wrench.
9 P ositioning table saw Locate the table saw in a well lit and level area where you can maintain good footing and balance. It should be installed in an area that leaves enough room to easi- ly handle the size of your workpieces.
10 Adjusting depth of cut The depth of cut may be adjusted by turning the han- dle. T urn the handle clockwise to raise the blade or counterclockwise to lower it. NOTE: • Use a shallow depth setting when cutting thin materi- als in order to obtain a cleaner cut.
After adjusting the positive stops, set the blade at 90 ° to the table surface. Then adjust the arrow pointer so that its right edge is aligned to the 0 ° graduation. Installing and adjusting rip fence Raise the grip of the rip fence. Install the rip fence on the table so that the fence holder engages with the guide rail.
12 CAUTION: • Always grasp the striped portion of the wrench when tightening the hex bolts. If you tighten the hex bolts while grasping the wrench further than the striped por- tion, the hex bolts may be damaged and/or an injury to your hand may result.
When operating the switch lever , it is convenient to view it through the window area in the table. CAUTION: • When not using the tool, remove the key and store it in a secure place.
14 Push stick A push stick can be easily made from a piece of ply- wood 19 mm (3/4 ” ) to 25 mm (1 ” ) thick. Cut out the hatched area on the stick and smooth edges with a file. (H) dimension should be less than 12.7 mm (1/2 ” ) so as to be thinner than the workpiece.
W ood facing (rip fence) A wood facing should be used for operations when the blade comes close to the rip fence. Wood facing for the rip fence should be the same size as the rip fence. Make sure the bottom of facing is flush with the table surface. Crosscutting CAUTION: • When making a crosscut, remove the rip fence from the table.
16 A uxiliary wood facing (miter gauge) T o prevent a long board from wobbling, fit the miter gauge with an auxiliary fence board. Fasten with bolts/nuts after drilling holes, but fasteners must not protrude from the face board. Ripping CAUTION: • When ripping, remove the miter gauge from the table.
3. T urn the tool on and gently feed the workpiece into the blade along with the rip fence. (1) When the width of rip is 150 mm (6 ” ) and wider , carefully use your right hand to feed the work- piece. Use your left hand to hold the workpiece in position against the rip fence.
CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning Clean out sawdust and chips from time to time. Carefully clean the blade guard and moving parts inside the table saw .
19 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated pur- pose.
T able insert (Part No. 317061-6) When cutting grooves 5/16 ” , 3/8 ” ,7/16 ” or 1/2 ” use this table insert instead of the standard table insert. T o install the dado head set, proceed as follows: 1. T urn the tool off and unplug it before installing.
21 NOTE: • When widths slightly greater than the above are required, fit the paper washers in between the inside and outside cutters to adjust the width. 5. Arrange the cutters so that the tips of the inside cut- ters are positioned at the gullets of the outside cutter .
Featherboards are used to keep the workpiece in con- tact with the rip fence and table as shown, and to stop kickbacks. T o install featherboards, proceed as follows: 1. T urn the tool off and unplug it. 2. Add 8 ” high flat facing board to the rip fence, the full length of the rip fence.
23 How to perf orm rabbeting 1. Remove blade guard. 2. Attach auxiliary fence to rip fence for cuts that run the length of the stock. Facing should be as high as the workpiece is wide. Adjust fence and blade to desired dimensions. 3. First cut: Hold board flat on table as in ordinary rip- ping.
24 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
21 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut.
22 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2.
2 7 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd.
W ARNING Some dust created by po wer sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th defects or other reproductiv e har m.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Makita 2703X1 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Makita 2703X1 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Makita 2703X1 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Makita 2703X1 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Makita 2703X1, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Makita 2703X1.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Makita 2703X1. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Makita 2703X1 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
